Business Networking Solution Installation Guide Jetstream Smart Switch T1500G-10MPS / T1600G-28TS / T1600G-28PS T1500-28TC (TL-SL2428) / T1500-28PCT (TL-SL2428P) T1600G-18TS (TL-SG2216) / T1600G-52TS (TL-SG2452) T1600G-52PS (TL-SG2452P) / T1700G-28TQ / T1700X-16TS
About this Installation Guide This Installation Guide describes the hardware characteristics, installation methods and the points that should be attended to during the installation. This Installation Guide is structured as follows: Chapter 1 Introduction This chapter describes the external components of the switch. Chapter 2 Installation This chapter illustrates how to install the switch. Chapter 3 Connection This chapter illustrates how to do the physical connection of the switch.
Contents Chapter 1 Introduction———————————— 01 1.1 Product Overview............................................................01 1.2 Appearance........................................................................01 Chapter 2 Installation———————————— 08 2.1 Package Contents...........................................................08 2.3 Installation Tools...............................................................10 2.2 2.4 Safety Precautions...........................................
JetStream Smart Switch Chapter 1 Introduction 1.1 Product Overview Designed for workgroups and departments, TP-Link JetStream Smart Switch provides wire-speed performance and abundant L2 management features. It provides a variety of service features and multiple powerful functions with high security. The EIA-standardized framework and smart configuration capacity can provide flexible solutions for a variable scale of networks. QoS and IGMP snooping/filtering optimize voice and video application.
JetStream Smart Switch The front panel of T1500G-10MPS is shown as the following figure. Figure 1-3 Front Panel of T1500G-10MPS LEDs LED Mode Switch Button Reset 10/100/1000Mbps RJ45 Port and PoE Port SFP Port The front panel of T1600G-18TS (TL-SG2216) is shown as the following figure. Figure 1-4 Front Panel of T1600G-18TS (TL-SG2216) LEDs Reset 10/100/1000Mbps RJ45 Port SFP Port The front panel of T1600G-28TS is shown as the following figure.
JetStream Smart Switch The front panel of The T1600G-52PS (TL-SG2452P) is shown as the following figure.
JetStream Smart Switch LED Indication Green On: Running at 1000Mbps, but no activity. Green Flashing: Running at 1000Mbps and is transmitting or receiving data. 1000M 10/100/1000Mbps Yellow On: Running at 10/100Mbps, but no activity. Yellow Flashing: Running at 10/100Mbps and is transmitting or receiving data. Off: No device is linked to the corresponding port. Note: 1000M for T1500-28TC. 10/100/1000Mbps for 1-24 ports of T1600G-28TS and 1-48 ports of T1600G-52TS (TL-SG2452).
JetStream Smart Switch the Speed LED will turn off and the PoE LED will light up. Then the PoE LED will turn off after being on for 60 seconds and the Speed LED will light up again. LED Indication PWR Off: The switch is powered off or power supply is abnormal. SYS FAN On: The switch is powered on. Flashing: Power supply is abnormal. Flashing: The switch works properly. On or Off: The switch works improperly. Green: All the fans work properly. Yellow: Not all the fans work properly.
JetStream Smart Switch LED Mode Switch Button Press this button to switch the LED status indication between Speed and PoE. Reset With the switch powered on, press Reset button for 5 seconds to reset the software setting to its factory default settings. Unit ID LED Designed to display the stack Unit ID of the switch. For the switch that does not join any stack system, it displays its default Unit ID.
JetStream Smart Switch ■■ Rear Panel The rear panel is shown as the following figure. Here we take T1600G-28TS as an example. Figure 1-11 Rear Panel Kensington Security slot Kensington Security Slot Grounding Terminal Power Socket Secure the lock (not provided) into the security slot to prevent the device from being stolen. Grounding Terminal The switch already comes with lightning protection mechanism.
JetStream Smart Switch Chapter 2 Installation 2.1 Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. One Power Cord One Switch Installation Guide Business Networking Solution Installation Guide Two mounting brackets and the fittings One Resouce CD 2.2 Safety Precautions To avoid any device damage and bodily injury caused by improper use, please observe the following rules.
JetStream Smart Switch Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device. For normal temperature and humidity of the device, please check the following table.
JetStream Smart Switch enough to damage electronic devices, more effective lightning protection measures should be taken. ■■ ■■ ■■ ■■ Ensure the rack and device are well earthed. Make sure the power socket has a good contact with the ground. Keep a reasonable cabling system and avoid induced lightning. Use the signal SPD (Surge Protective Device) when wiring outdoor.
JetStream Smart Switch Figure 2-1 Desktop Installation Feet Bottom of the Device Notch ■■ Rack Installation To install the device in an EIA standard-sized, 19-inch rack, follow the instructions described below: 1. Check the grounding and stability of the rack. 2. Secure the supplied rack-mounting brackets to each side of the device with supplied screws, as illustrated in the following figure. Figure 2-2 Bracket Installation Rack-mounting Bracket Screw 3.
JetStream Smart Switch Chapter 3 Connection 3.1 Ethernet Port Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shows. Figure 3-1 Connecting the RJ45 Port RJ45 Port 3.2 RJ45 Cable SFP/SFP+ Port The following figure demonstrates the connection of SFP port to an SFP module. Figure 3-2 Inserting the SFP Module SFP/SFP+ Slot F SFP/SFP+ Module PWR SYS Reset F 3.
JetStream Smart Switch 3.4 Power On Plug in the negative connector of the provided power cord into the power socket of the device, and the positive connector into a power outlet as the following figure shows. Figure 3-3 Connecting to Power Supply 100-240V~5 0/60H z 0.5A Note: The figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above.
JetStream Smart Switch Appendix A Troubleshooting Q1. What could I do if I forgot the username and password of the switch? Press the Reset button for at least 5 seconds to reset the system. The system will be reset to the factory default settings, and the default login user name and password are both admin. Q2. Why does the PWR/Power LED work abnormally? The PWR/Power LED should be lit up when the power system works normally. If the PWR LED worked abnormally, please take the following steps: 1.
JetStream Smart Switch Appendix B Specifications Item Standards Content IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3z, IEEE 802.3x, IEEE 802.1p, IEEE 802.1q, IEEE 802.1x, IEEE 802.1d, IEEE 802.1s, IEEE 802.1w IEEE 802.3ae (For T1700G-28TQ / T1700X-16TS) IEEE 802.3af, IEEE 802.3at (For T1500-18PCT / T1500G-10MPS / T1600G28PS / T1600G-52PS) 10Base-T: UTP/STP of Cat. 3 or above 100Base-TX: UTP/STP of Cat.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
• Do not use damaged charger or USB cable to charge the device.
Symbol Explanation RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
For technical support, User Guide and other information, please visit http://www.tp-link.com/support, or simply scan the QR code © 2018 TP-Link 7106508056 REV4.0.
