Business Networking Solution Installation Guide JetStream Gigabit Smart Switch T1600G-18TS (TL-SG2216) T1600G-28TS (TL-SG2424) / T1600G-52TS (TL-SG2452) T1600G-28PS (TL-SG2424P) / T1600G-52PS (TL-SG2452P)
About this Installation Guide This Installation Guide describes the hardware characteristics, installation methods and the points that should be attended to during installation. This Installation Guide is structured as follows: Chapter 1 Introduction. This chapter describes the external components of the switch. Chapter 2 Installation. This chapter illustrates how to install the switch. Chapter 3 Lightning Protection. This chapter illustrates how to prevent lightning damage. Chapter 4 Connection.
JetStream Gigabit Smart Switch Contents Chapter 1 Introduction———————————— 01 1.1 1.2 Product Overview..................................................01 Appearance.....................................................................01 Chapter 2 Installation———————————— 09 2.1 2.2 2.3 2.4 Package Contents................................................09 Safety Precautions...............................................09 Installation Tools....................................................
JetStream Gigabit Smart Switch Chapter 1 Introduction 1.1 Product Overview TP-Link Gigabit Smart Switch, designed for workgroups and departments, provides wire-speed performance and abundant L2 and L2+ management features. It provides a variety of service features and multiple powerful functions with high security. The EIA-standardized framework and smart configuration capacity can provide flexible solutions for a variable scale of networks.
JetStream Gigabit Smart Switch LEDs LED Status Indication PWR Off The switch is powered off or power supply is abnormal On The switch is powered on Flashing Power supply is abnormal Flashing The switch is working normally SYS On/Off Link/Act 1000Mbps On The switch is working abnormally There is a device connected to the corresponding port but no activity Flashing Data is being transmitted or received Off No device is connected to the corresponding port Off A 10/100Mbps device or no devi
JetStream Gigabit Smart Switch LEDs LED Status Indication PWR Off The switch is powered off or power supply is abnormal On The switch is powered on Flashing Power supply is abnormal Flashing The switch is working normally SYS On/Off Link/Act 1000Mbps On The switch is working abnormally There is a device connected to the corresponding port but no activity Flashing Data is being transmitted or received Off No device is connected to the corresponding port Off A 10/100Mbps device or no devi
JetStream Gigabit Smart Switch LEDs LED Status Indication PWR Off The switch is powered off or power supply is abnormal On The switch is powered on Flashing Flashing SYS On/Off 10/100/ 1000Mbps (port 1-48) Green Yellow Off On Power supply is abnormal The switch works properly The switch works improperly A 1000Mbps device is connected to the corresponding port, but no activity Flashing Data is being transmitted or received On A 10/100Mbps device is connected to the corresponding port, bu
JetStream Gigabit Smart Switch LEDs T1600G-28PS has an LED mode switch button which is for switching the LED status indication. When the Speed LED is on, the port LED is indicating the data transmission status. When the PoE LED is on, the port LED is indicating the power supply status. By default, the Speed LED is on. Pressing the mode switch button, the Speed LED will turn off and the PoE LED will light up. Then the PoE LED will turn off after being on for 60 seconds and the Speed LED will light up again.
JetStream Gigabit Smart Switch LED Status Speed or PoE Green (port 1-24) Yellow Off On Flashing On Indication The port is supplying power normally The supply power exceeds the corresponding port's maximum power Overload or short circuit is detected No PoE power supply is provided on the port LED Mode Switch Button Press this button to switch the LED status indication between Speed and PoE.
JetStream Gigabit Smart Switch When the Speed LED is on, the port LED is indicating the data transmission status.
JetStream Gigabit Smart Switch LED Mode Switch Button Press this button to switch the LED status indication between Speed and PoE. Reset Press this button for five seconds or above to reset the software setting back to factory default settings. 10/100/1000Mbps RJ45 Port Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a corresponding Speed or PoE LED. SFP Port Designed to install the SFP module.
JetStream Gigabit Smart Switch Chapter 2 Installation 2.1 Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. One Switch One Power Cord This Installation Guide Business Networking Solution Installation Guide Two mounting brackets, eight screws and four rubber feet 2.
JetStream Gigabit Smart Switch ■■ Site Requirements Temperature/Humidity 40℃ 0℃ Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device. For normal temperature and humidity of the device, please check the following table.
JetStream Gigabit Smart Switch Lightning Protection Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000℃. As this instant current is strong enough to damage electronic devices, more effective lightning protection measures should be taken. ■■ ■■ ■■ ■■ Ensure the rack and device are well earthed. Make sure the power socket has a good contact with the ground.
JetStream Gigabit Smart Switch 2.4 Product Installation ■■ Desktop Installation To install the device on the desktop, please follow the steps: 1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings. 2. Remove the adhesive backing papers from the rubber feet. 3. Turnover the device and attach the supplied rubber feet to the recessed areas on the bottom at each corner of the device.
JetStream Gigabit Smart Switch Figure 2-9 Rack Installation Rack Caution: Please set 5~10cm gaps around the device for air circulation. Please avoid any heavy thing placed on the device. Please mount devices in sequence from the bottom to top of the rack and ensure a certain clearance between devices for the purpose of heat dissipation.
JetStream Gigabit Smart Switch Chapter 3 Lightning Protection 3.1 Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lightning to devices. Note: It's not recommended using Ethernet cables outdoors. When cabling outdoors, please use a signal lightning arrester.
JetStream Gigabit Smart Switch ■■ Requirements for Cabling Indoors When cabling indoors, keep a certain distance away from the devices that may cause high-frequency interferences, such as down-conductor cable, powerline, power transformer and electromotor. ■■ ■■ The main cable should be paved in the metal raceway of the access shaft. When cabling, keep the loop area formed by the cable itself as small as possible.
JetStream Gigabit Smart Switch Cable 2~5kVA powerline >5kVA powerline Pave Way Parallel cabling One is in the grounded metal raceway or metal pipe The both are in the grounded metal raceway or metal pipe 300 150 80 Parallel cabling 600 The both are in the grounded metal raceway or metal pipe 150 One is in the grounded metal raceway or metal pipe Device Min Distance (m) Transformer room 2.00 Air-conditioner room 2.00 Switch case Elevator tower 3.2 Min Parallel Length (mm) 300 1.00 2.
JetStream Gigabit Smart Switch Figure 3-1 Connecting to the Ground via Power Supply Switch (Rear Panel) AC Power Cord (with PE cable) Note: The figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above.
JetStream Gigabit Smart Switch Equipotential Bonding Equipotential Bonding is the practice of intentionally electrically connecting all earthed systems to the same grounding grid or connecting the grounding grids of all the earthed systems together through the ground or overground metal so as to create an earthed equipotential zone.
JetStream Gigabit Smart Switch Signal lightning arrester is used to protect RJ45 ports of the device from lightning. When cabling outdoors, please install a signal lightning arrester before connecting the cable to the device. When purchasing or using a signal lightning arrester, please observe the following rules: ■■ ■■ The port rate of the signal lightning arrester should match the rate of the desired port on the device. If it is not matched, this signal lighting arrester will not work.
JetStream Gigabit Smart Switch Chapter 4 Connection 4.1 Ethernet Port Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shown. Figure 4-1 Connecting the RJ45 Port RJ45 Port 4.2 RJ45 Cable SFP Port Connect the SFP port to a SFP module as shown below. Figure 4-2 Inserting the SFP Module SFP Port SFP Module 4.
JetStream Gigabit Smart Switch 4.4 Power On Plug in the negative connector of the provided power cord into the power socket of the device, and the positive connector into a power outlet as the following figure shown. Figure 4-3 Connecting to Power Supply 2 1 Note: The figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above. 4.
JetStream Gigabit Smart Switch Chapter 5 Configuration 5.1 Configure the Switch via GUI 1. To access the GUI of the switch, open a web browser and t ype the default management address http://192.168.0.1 in the address field of the browser, then press the Enter key. Figure 5-1 Web Browser Note: To log in to the GUI of the switch, the IP address of your PC should be set in the same subnet addresses of the switch. The IP address is 192.168.0.x ("x" is any number from 2 to 254), Subnet Mask is 255.255.255.
JetStream Gigabit Smart Switch Figure 5-3 5.2 Main Page of the Switch Configure the Switch Using CLI You can log on to the switch and access the CLI by Logging on to the switch remotely by a Telnet connection through an Ethernet port. To log on to the switch by a Telnet connection, please take the following steps: 1. Make sure the switch and the PC are in the same LAN. Click Start and type in "cmd" in the Search programs and files window and press the Enter button. Figure 5-4 Run Window 2.
JetStream Gigabit Smart Switch Appendix A Troubleshooting Q1. What could I do if I forgot the username and password of the switch? Press the Reset button for at least 5 seconds to reset the system. The system will be reset to the factory default settings, and the default login user name and password are both admin. Q2. Why does the PWR LED work abnormally? The PWR LED should be lit up when the power system works normally. If the PWR LED worked abnormally, please take the following steps: 1. 2.
JetStream Gigabit Smart Switch Appendix B Specifications Item Content Standards IEEE 802.3, IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3z, IEEE 802.3x, IEEE 802.1p, IEEE 802.1q, IEEE 802.1x, IEEE 802.1d, IEEE 802.1s, IEEE 802.1w IEEE 802.3af/at (T1600G-28PS/T1600G-52PS) 10Base-T: UTP/STP of Cat. 3 or above (maximum 100m) Transmission Medium 100Base-TX: 2-pair UTP/STP of Cat. 5 or above (maximum 100m) 1000Base-T: 4-pair UTP/STP of Cat. 5e and Cat.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
BSMI Notice 安全諮詢及注意事項 1) 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 2) 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 3) 注意防潮，請勿將水或其他液體潑灑到本產品上。 4) 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 5) 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 6) 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。 7) 此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要求採取某 些適當的對策。 Industry Canada Statement CAN ICES-3 (A)/NMB-3(A) Explanation of the symbols on the product label Symbol Explanation AC voltage Indoor use only RECYCLING This product bears the selective sorting symb
For technical support and other information, please visit http://www.tp-link.com/support, or simply scan the QR code. The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public License (“GPL”). As applicable, the terms of the GPL and any information on obtaining access to the respective GPL Code used in TP-Link products are available to you in GPL-Code-Centre under (http://www.tp-link.com/en/support/gpl/).
