TL-WR340G TL-WR340GD 54Mbps Wireless Router Rev: 1.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2011 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
National Restrictions 2400.0-2483.5 MHz Country Restriction General authorization required for outdoor use and Bulgaria France public service Outdoor use limited to 10 Military Radiolocation use. Refarming of the 2.4 GHz band mW e.i.r.p. within the band has been ongoing in recent years to allow current relaxed 2454-2483.5 MHz regulation.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 54Mbps Wireless Router Model No.: TL-WR340G/TL-WR340GD Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 1999/5/EC The above product is in conformity with the following standards or other normative documents: ETSI EN 300 328 V1.7.
CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Introduction ........................................................................................ 2 1.1 Product Overview ...................................................................................................... 2 1.2 Main Features ...........................................................................................................
4.8 4.9 4.7.2 Port Triggering................................................................................................................39 4.7.3 DMZ................................................................................................................................41 4.7.4 UPnP ..............................................................................................................................42 Security .......................................................................
Package Contents The following contents should be found in your box: ¾ One TL-WR340G/TL-WR340GD 54Mbps Wireless Router ¾ One AC power Adapter for TL-WR340G/TL-WR340GD 54Mbps Wireless Router ¾ Quick Installation Guide ¾ One Resource CD for TL-WR340G/TL-WR340GD 54Mbps Wireless Router, including: • This Guide • Easy Setup Assistant • Other Helpful Information ) Note: Make sure that the package contains the above items.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Chapter 1. Introduction Thank you for choosing the TL-WR340G/TL-WR340GD 54Mbps Wireless Router. 1.1 Product Overview Thank you for choosing the TL-WR340G/TL-WR340GD 54Mbps Wireless Router. This router provides dedicated solution for Small Office/Home Office (SOHO) networks. With your network all connected, your local wired or wireless network can share Internet access, files and fun for multiple PCs through one ISP account.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide ¾ Supports connecting/disconnecting from the Internet on a specified time of day. ¾ Supports access control, parents and network administrators can establish restricted access policies based on time of day for children or staff.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The Router’s LEDs are located on the front panel (View from left to right).
TL-WR340G/TL-WR340GD 2.2 54Mbps Wireless Router User Guide The Back Panel Figure 2-2 The following parts are located on the rear panel (View from left to right). ¾ POWER: The Power plug is where you will connect the power adapter. ¾ 1, 2, 3, 4 (LAN): Through these ports, you can connect the Router to your PCs and the other Ethernet network devices. ¾ WAN: RJ45 WAN port for connecting the router to a cable/DSL Modem, or Ethernet. ¾ RESET: There are two ways to reset the Router's factory defaults.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide ¾ Each PC in the LAN needs a working Ethernet Adapter and an Ethernet cable with RJ45 connectors ¾ TCP/IP protocol must be installed on each PC ¾ Web browser, such as Microsoft Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later 2.4 Installation Environment Requirements ¾ The Product should not be located where it will be exposed to moisture or excessive heat.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 2-3 Hardware Installation of the Router 2.6 Configure PC Your PC needs a network adapter. You may directly connect your adapter to the Router, or you may connect your adapter to a Hub/Switch, and then connect the Hub/Switch to the Router. Follow the instructions below to configure a computer running Windows XP to be a DHCP client. 1. From the Start menu on your desktop, go to Settings, and then click on Network Connections.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 2-4 2. In the Network Connections window, right-click on LAN (Local Area Connection), then click Properties. Figure 2-5 3. In the General tab of Internet Protocol (TCP/IP) Properties menu, highlight Internet Protocol (TCP/IP) under This connection uses the following items by clicking on it once. Click on the Properties button.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 2-6 4. Select Obtain an IP address automatically by clicking the radio-button. Click OK.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your TL-WR340G 54Mbps Wireless Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration Connect the local PC to the LAN ports of the Router. And then you can configure the IP address for your PC in the following way. 1) Set up the TCP/IP Protocol in Obtain an IP address automatically mode on your PC.
TL-WR340G/TL-WR340GD Figure 3-2 54Mbps Wireless Router User Guide Login Windows ) Note: If the above screen does not pop up, it means that your Web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it. 2. After successfully log in, you can click the Quick Setup menu to quickly configure your Router. Figure 3-3 3.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide The Router supports three popular ways PPPoE, Dynamic IP and Static IP to connect to the Internet. 4. Select your connection type. 1) If the connection type selected is PPPoE, the next screen will appear as shown in Figure 3-5. Figure 3-5 ¾ Quick Setup - PPPoE User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case sensitive. If you have difficulty with this process, please contact your ISP.
TL-WR340G/TL-WR340GD 5. 54Mbps Wireless Router User Guide Click Next to continue, the Wireless settings page will appear as shown in Figure 3-7. Figure 3-7 Quick Setup – Wireless ¾ Wireless Radio - Enable or disable the wireless radio choosing from the pull-down list. ¾ SSID - Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide It is recommended strongly that you choose one of following options to enable security. z WPA-PSK/WPA2-PSK - Select WPA based on pre-shared passphrase. z PSK Password - You can enter ASCII or Hexadecimal characters. For ASCII,the length should be between 8 and 63 characters. For Hexadecimal,the length should be between 8 and 64 characters. Please note that the key is case sensitive.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Chapter 4. Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation, For advanced users, if you want to know more about this device and make use of its functions adequately, you need to read this chapter and configure advanced settings though the Web-based Utility. 4.1 Login After your successful login, you can configure and manage the device.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 4-1 Router Status 4.3 Quick Setup Please refer to Quick Installation Guide.
TL-WR340G/TL-WR340GD 4.4 54Mbps Wireless Router User Guide Network Figure 4-2 the Network menu There are three submenus under the Network menu (shown in Figure 4-2): WAN, LAN and MAC Clone. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.4.1 WAN You can configure the WAN port parameters on this page.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 4-3 WAN – Dynamic IP This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters. ¾ MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. For some ISPs you need to reduce the MTU.
TL-WR340G/TL-WR340GD 2. 54Mbps Wireless Router User Guide If you choose Static IP, you should have fixed IP parameters specified by your ISP. The Static IP settings page will appear, shown in Figure 4-4: Figure 4-4 WAN - Static IP You should type the following parameters into the spaces provided: ¾ IP Address - Enter the IP address in dotted-decimal notation provided by your ISP. ¾ Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 4-5 WAN - PPPoE ¾ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾ Secondary Connection - It's available only for PPPoE Connection. If your ISP provides an extra Connection type such as Dynamic/Static IP to connect to a local area network, then you can check the radio button of Dynamic/Static IP to activate this secondary connection.
TL-WR340G/TL-WR340GD ¾ 54Mbps Wireless Router User Guide Time-based Connecting - You can configure the router to make it connect or disconnect based on time. Enter the start time in HH:MM format for connecting and end time in HH:MM format for disconnecting in the Period of Time fields. ) Note: Only when you have configured the system time on System Tools -> Time page, will the Time-based Connecting function can take effect.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide ¾ ISP Specified IP Address - If you know that your ISP does not automatically transmit your IP address to the router during login, click “Use the IP Address specified by ISP” check box and enter the IP Address in dotted-decimal notation, which your ISP provided. ¾ Detect Online Interval - The default value is 0, you can input the value between 0 and 120. The router will detect Access Concentrator online at every interval between seconds.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. ¾ Connect on Demand - You can configure the router to disconnect from your Internet connection after a specified period of inactivity (Max Idle Time).
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 4-8 PPTP/Russia PPTP Settings ¾ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾ Dynamic IP/ Static IP – Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name. If you choose static IP and enter the domain name, you should also enter the DNS assigned by your ISP. And click the Save button. Click the Connect button to connect immediately.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide enter the number of minutes you want to have elapsed before your Internet connection terminates. Caution: Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time, since some applications are visiting the Internet continually in the background. ¾ Connect Automatically - Connect automatically after the router is disconnected. To use this option, click the radio button.
TL-WR340G/TL-WR340GD 4.4.3 54Mbps Wireless Router User Guide MAC Clone You can configure the MAC address of the WAN port on this page, Figure 4-10: Figure 4-10 MAC Address Clone Some ISPs require that you register the MAC Address of your adapter, which is connected to your cable/DSL Modem or Ethernet during installation. Changes are rarely needed here. ¾ WAN MAC Address - This field displays the current MAC address of the WAN port, which is used for the WAN port.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.5.1 Wireless Settings The basic settings for the wireless network are set on this page, Figure 4-12: Figure 4-12 Wireless Settings ¾ SSID - Enter a value of up to 32 characters. The same name (SSID) must be assigned to all wireless devices in your network.
TL-WR340G/TL-WR340GD ¾ 54Mbps Wireless Router User Guide Mode - If all of the wireless devices connected with this wireless router can connect in the same transmission mode(eg. 802.11b), you can choose "Only" mode(eg. 11b only). If you have some devices that use a different transmission mode, choose the appropriate "Mixed" mode. ¾ Enable Wireless Router Radio - The wireless radio of this Router can be enabled or disabled to allow wireless stations access.
TL-WR340G/TL-WR340GD 4.5.2 54Mbps Wireless Router User Guide Security Settings Options related to security can be set on this page. Figure 4-15 Wireless Security You can select one of the following security options: ¾ Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. It is recommended strongly that you choose one of following options to enable security.
TL-WR340G/TL-WR340GD z ¾ 54Mbps Wireless Router User Guide Shared Key - Select 802.11 Shared Key authentication. WEP Key Format - You can select ASCII or Hexadecimal format. ASCII Code Format stands for any combination of keyboard characters in the specified length. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length.
TL-WR340G/TL-WR340GD ¾ 54Mbps Wireless Router User Guide PSK Password - You can enter ASCII or Hexadecimal characters. For Hexadecimal, the length should be between 8 and 64 characters; for ASCII, the length should be between 8 and 63 characters. ¾ Group Key Update Period - Specify the group key update interval in seconds. The value can be either 0 or at least 30. Enter 0 to disable the update. Be sure to click the Save button to save your settings on this page.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide otherwise, select the radio button Deny the stations not specified by any enabled entries in the list to access. To Add a Wireless MAC Address filtering entry, click the Add New… button. The Add or Modify Wireless MAC Address Filtering entry page will appear, shown in Figure 4-17: Figure 4-17 Add or Modify Wireless MAC Address Filtering entry To add a MAC Address Filtering entry, follow these instructions: 1.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide 2. Select the radio button: Deny the stations not specified by any enabled entries in the list to access for Filtering Rules. 3. Delete all or disable all entries if there are any entries already. 4. Click the Add New... button and enter the MAC address 00-0A-EB-00-07-BE in the MAC Address field, enter wireless station A in the Description field, select Allow in the Privilege pull-down list and select Enabled in the Status pull-down list.
TL-WR340G/TL-WR340GD ¾ 54Mbps Wireless Router User Guide RTS Threshold - Here you can specify the RTS (Request to Send) Threshold. If the packet is larger than the specified RTS Threshold size, the Router will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is 2346. ¾ Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented.
TL-WR340G/TL-WR340GD 4.6 54Mbps Wireless Router User Guide DHCP Figure 4-20 The DHCP menu There are three submenus under the DHCP menu (shown in Figure 4-20): DHCP Settings, DHCP Clients List and Address Reservation. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.6.
TL-WR340G/TL-WR340GD ¾ ¾ ¾ 54Mbps Wireless Router User Guide Default Domain - (Optional.) Input the domain name of your network. Primary DNS - (Optional.) Input the DNS IP address provided by your ISP. Or consult your ISP. Secondary DNS - (Optional.) Input the IP address of another DNS server if your ISP provides two DNS servers. ) Note: To use the DHCP server function of the router, you must configure all computers on the LAN as "Obtain an IP Address automatically" mode.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 4-23 Address Reservation ¾ MAC Address - The MAC address of the PC of which you want to reserve IP address. ¾ Assigned IP Address - The IP address of the router reserved. ¾ Status - The status of this entry either Enabled or Disabled. To Reserve IP addresses: 1. 2. Click the Add New button. (Pop-up Figure 4-23) Enter the MAC address (The format for the MAC Address is XX-XX-XX-XX-XX-XX.
TL-WR340G/TL-WR340GD 4.7 54Mbps Wireless Router User Guide Forwarding Figure 4-25 The Forwarding menu There are four submenus under the Forwarding menu: Virtual Servers, Port Triggering, DMZ and UPnP. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.7.1 Virtual Servers Virtual servers can be used for setting up public services on your LAN, such as DNS, Email and FTP.
TL-WR340G/TL-WR340GD 5. 6. 54Mbps Wireless Router User Guide Select the Enable checkbox to enable the virtual server. Click the Save button. Figure 4-27 Add or Modify a Virtual Server Entry ) Note: It is possible that you have a computer or server that has more than one type of available service. If so, select another service, and enter the same IP Address for that computer or server. To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 4-28 Port Triggering Once configured, operation is as follows: 1. A local host makes an outgoing connection using a destination port number defined in the Trigger Port field. 2. The router records this connection, opens the incoming port or ports associated with this entry in the Port Triggering table, and associates them with the local host. 3.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 4-29 Add or Modify a Triggering Entry There are many popular applications in the Popular Application list. You can select it, and the application will fill in the Trigger Port, incoming Ports Range boxes and select the Enable checkbox. It has the same effect as adding a new rule. To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 4-30 DMZ To assign a computer or server to be a DMZ server: 1. 2. Click the Enable radio button Enter the local host IP Address in the DMZ Host IP Address field ) Note: After you set the DMZ host, the firewall related to the host will not work. 4.7.4 UPnP The Universal Plug and Play (UPnP) feature allows the devices, such as Internet computers, to access the local host resources or devices as needed.
TL-WR340G/TL-WR340GD 4.8 54Mbps Wireless Router User Guide Security Figure 4-32 The Security menu There are six submenus under the Security menu: Firewall, IP Address Filtering, Domain Filtering, MAC Address Filtering, Remote Management and Advanced Security. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.8.1 Firewall Using the Firewall page, you can turn the general firewall switch on or off.
TL-WR340G/TL-WR340GD 4.8.2 54Mbps Wireless Router User Guide IP Address Filtering The IP address Filtering feature allows you to control Internet Access by specific users on your LAN based on their IP addresses. The IP address filtering is set on this page: Figure 4-34 IP address Filtering To disable the IP Address Filtering feature, keep the default setting, Disabled.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide 5. WAN Port - Enter a WAN Port or a range of WAN Ports in the field. For example, 25 – 110. Keep the field open, which means all WAN Ports have been put into the field. 6. Protocol - Select which protocol is to be used, either TCP, UDP, or All (all protocols supported by the router). 7. 8. 9. Action - Select either Allow or Deny through the router. Status - Select Enabled or Disabled for this entry on the Status pull-down list.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Before adding a Domain Filtering entry, you must ensure that Enable Firewall and Enable Domain Filtering have been selected on the Firewall page. To Add a Domain filtering entry, click the Add New… button. The page "Add or Modify a Domain Filtering entry " will appear, shown in Figure 4-37: Figure 4-37 Add or Modify a Domain Filtering entry To add or modify a Domain Filtering entry, follow these instructions: 1.
TL-WR340G/TL-WR340GD 4.8.4 54Mbps Wireless Router User Guide MAC Address Filtering Like the IP Address Filtering page, the MAC Address Filtering page allows you to control access to the Internet by users on your local network based on their MAC Address. Figure 4-38 MAC address Filtering Before setting up MAC Filtering entries, you must ensure that Enable Firewall and Enable MAC Filtering have been selected on the Firewall page. To Add a MAC Address filtering entry, clicking the Add New… button.
TL-WR340G/TL-WR340GD 2. Modify the information. 3. Click the Save button. 54Mbps Wireless Router User Guide Click the Enable All button to make all entries enabled. Click the Disabled All button to make all entries disabled. Click the Delete All button to delete all entries Click the Next button to go to the next page and click the Previous button to return to the previous page.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide example, if your Router's WAN address is 202.96.12.8 and you use port number 8080, enter in your browser: http://202.96.12.8:8080. You will be asked for the router's password. After successfully entering the password, you will be able to access the router's Web-based utility. ) Note: Be sure to change the router's default password to a very secure password. 4.8.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide ¾ UDP-FLOOD Packets threshold: (5 ~ 3600) - The default value is 50. Enter a value between 5 ~ 3600 packets. When the current UPD-FLOOD Packets numbers is beyond the set value, the router will start up the blocking function immediately. ¾ Enable TCP-SYN-FLOOD Attack Filtering - Enable or Disable the TCP-SYN- FLOOD Attack Filtering. ¾ TCP-SYN-FLOOD Packets threshold: (5 ~ 3600) - The default value is 50. Enter a value between 5 ~ 3600 packets.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 4-43 Static Routing To add static routing entries: 1. Click the Add New button. 2. Enter the following data: ¾ Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route. ¾ Subnet Mask - The Subnet Mask determines which portion of an IP Address is the network portion, and which portion is the host portion.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Click the Delete All button to delete all entries 4.10 IP QoS You can configure the IP QoS function on this page. Figure 4-45 IP QoS ¾ Enable IP QoS - Enable or disable the function of IP QoS. ¾ Choose BandWidth Type - Select the network connection type from the drop-down list. ¾ Bandwidth Apply - The bandwidth you get. If you are not clear about that, please contact with your ISP for help. ¾ IP Range - IP range of this entry.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide 3. If no IP QoS item is enabled, the Bandwidth Apply won't be effective. 4. IP address range for different entries could not have intersection with each other. 5. After the configurations, click the Save button for the change to take effect. 4.11 IP & MAC Binding Setting Figure 4-46 the IP & MAC Binding menu There are two submenus under the IP &MAC Binding menu: Binding Setting and ARP List.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 4-48 IP & MAC Binding Setting (Add & Modify) To add IP & MAC Binding entries: 1. Click the Add New.. button. 2. Enter the MAC Address and IP Address. 3. Select the Bind checkbox. 4. Click the Save button to save it. To modify or delete an existing entry: 1. Find the desired entry in the table. 2. Click Modify or Delete as desired on the Modify column. To find an existing entry: 1. Click the Find button (shown in Figure 4-47). 2.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide the ARP list also. This page displays the ARP List; it shows all the existing IP & MAC Binding entries. Figure 4-50 ARP List ¾ MAC Address - The MAC address of the controlled computer in the LAN. ¾ IP Address - The assigned IP address of the controlled computer in the LAN. ¾ Status - Enabled or Disabled of the MAC address and IP address binding. ¾ Configure - Load or delete item. ¾ Load - Load the item to the IP & MAC Binding list.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 4-51 Dyndns.org DDNS Settings To set up for DDNS, follow these instructions: 1. 2. 3. 4. ¾ Type the domain names your dynamic DNS service provider gave. Type the User Name for your DDNS account. Type the Password for your DDNS account. Click the Login button to login to the DDNS service. Connection Status -The status of the DDNS service connection is displayed here. Click Logout to logout of the DDNS service. 4.12.2 Oray.
TL-WR340G/TL-WR340GD 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Click the Login button to login the DDNS service. 54Mbps Wireless Router User Guide ¾ Connection Status - The status of the DDNS service connection is displayed here. ¾ Domain Name - The domain names are displayed here. Click Logout to logout the DDNS service. 4.12.3 Comexe.cn DDNS If your selected dynamic DNS Service Provider is www.comexe.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide 4.13 System Tools Figure 4-54 The System Tools menu There are nine submenus under the System Tools menu: Time, Diagnostic, Firmware, Factory Defaults, Backup and Restore, Reboot, Password, Log and Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.13.
TL-WR340G/TL-WR340GD 3. Enter the Time in Hour/Minute/Second format. 4. Click Save. 54Mbps Wireless Router User Guide For automatic time synchronization: 1. Enter the address of the NTP Server Prior. 2. Click the Get GMT button to get GMT time from Internet if you have connected to Internet. ) Note: This setting will be used for some time-based functions such as firewall.
TL-WR340G/TL-WR340GD z 54Mbps Wireless Router User Guide Traceroute - This diagnostic tool tests the performance of a connection. ) Note: You can use ping/traceroute to test both numeric IP address or domain name. If pinging/tracerouting the IP address is successful, but pinging/tracerouting the domain name is not, you might have a name resolution problem. In this case, ensure that the domain name you are specifying can be resolved by using Domain Name System (DNS) queries.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 4-58 Firmware Upgrade New firmware is posted at http://www.tp-link.com and can be downloaded for free. If the router is not experiencing difficulties, there is no need to upgrade firmware, unless the new firmware supports a new feature you need. ) Note: When you upgrade the router's firmware, you will lose current configuration settings, so make sure you backup the router’s settings before you upgrade its firmware.
TL-WR340G/TL-WR340GD ¾ 54Mbps Wireless Router User Guide The default access: tplinklogin.net ) Note: Any settings you have saved will be lost when the default settings are restored. 4.13.5 Backup & Restore This page allows you to save current configuration of router as backup or restore the configuration file you saved before. Figure 4-60 Backup & Restore Configuration ¾ Click the Backup button to save all configuration settings as a backup file in your local computer.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide ¾ Upgrade the firmware of the router (system will reboot automatically). ¾ Restore the router's settings to factory default (system will reboot automatically). 4.13.7 Password This page allows you to change the factory default user name and password of the router. Figure 4-62 Password It is recommended strongly that you change the factory default user name and password of the router.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide 4.13.9 Statistics The Statistics page displays the network traffic of each PC in LAN, including total traffic and traffic of the last Packets Statistic interval seconds. Figure 4-64 Statistics ¾ Current Statistics Status - Enable or Disable. The default value is disabled. To enable, click the Enable button. If disabled, the function of DoS protection in Security settings will be ineffective. ¾ Packets Statistics Interval - The default value is 10.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Appendix A: FAQ 1. How do I configure the router to access Internet by ADSL users? 1) 2) 3) First, configure the ADSL Modem configured in RFC1483 bridge model. Connect the Ethernet cable from your ADSL Modem to the WAN port on the router. The telephone cord plugs into the Line port of the ADSL Modem. Login to the router, click the “Network” menu on the left of your browser, and click "WAN" submenu.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide ) Note: Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time, since some applications is visiting the Internet continually in the background. If you are a Cable user, please configure the router following the above steps. 2. How do I configure the router to access Internet by Ethernet users? 1) 2) Login to the router, click the “Network” menu on the left of your browser, and click "WAN" submenu.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide ) Note: Your opposite side should call your WAN IP, which is displayed on the “Status” page. 4) How to enable DMZ Host: Login to the router, click the “Forwarding” menu on the left of your browser, and click "DMZ" submenu. On the "DMZ" page, click “Enable” radio and type your IP address into the “DMZ Host IP Address” field, using 192.168.1.169 as an example, remember to click the "Save” button. DMZ 4.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Virtual Server 68
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if necessary. 1. Configure TCP/IP component 1) On the Windows taskbar, click the Start button, and then click Control Panel.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 0-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Figure 0-3 ) Note: For Windows 98 OS or before, the PC and Router may need to be restarted.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Appendix C: Specifications General Standards and Protocols Safety & Emission LEDs Ports IEEE 802.3,IEEE 802.3u, IEEE 802.11b and IEEE 802.11g TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP FCC、CE Power, SYS, WLAN, WAN, 1-4 One 10/100M Auto-Negotiation WAN RJ45 port, Four 10/100M Auto-Negotiation LAN RJ45 ports supporting Auto MDI/MDIX Wireless Modulation Frequency* Wireless Data Rates Media Access Protocol Security IEEE 802.
TL-WR340G/TL-WR340GD 54Mbps Wireless Router User Guide Appendix D: Glossary Access Point - A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network. Ad-hoc Network - An ad-hoc network is a group of computers, each with a wireless adapter, connected as an independent IEEE 802.11 wireless LAN.
