Installation Manual

ManualsBrandsTP-LINK ManualsComputers & AccessoriesTP-Link EAP225 V3 Wireless MU-MIMO Gigabit Ceiling Mount Access Point, Supports 802.3af PoE and Passive PoE(Injector Included), AC1350

Typical Network Topology

Hardware Installation

Option 1: Ceiling Mounting

Feed the Ethernet cable through the hole

and set the ceiling tile back into place.

Place the mounting bracket in the center

of the ceiling tile. Mark three positions for

the screw holes and a position for the

Ethernet cable hole.

Drill three 4mm diameter holes for the

screws and a 25mm diameter hole for the

Ethernet cable at the marked positions.

Remove the ceiling tile.

Secure the mounting bracket to the

ceiling tile using three M3x30 pan-head

screws, washers and wing nuts, as shown

on the left.

A DHCP server (typically a router) with DHCP function enabled is required to assign IP addresses to the EAPs and

clients in your local network.

Option 1: Ceiling Mounting

Option 2: Wall Mounting

The EAP can be ceiling-mounted or wall-mounted.

Quick Installation Guide

EAP110/EAP115/EAP225

Wireless Access Point

LED Indication

Interface Panel

RESET

With the device powered on, press and hold the button for about 5 seconds until the LED flashes red, then

release the button. The device will restore to factory default settings.

The device is working properly.

Solid Green

System errors. RAM, Flash, Ethernet,

WLAN or firmware may be

malfunctioning.

Flashing Red

The device is being reset to its

factory default settings.

Double-flashing Red, Green, Yellow

Firmware update is in progress. Do not

disconnect or power o the device.

Flashing Yellow

The port is used to connect to a router or a switch to transmit data or to a PSE (Power Sourcing Equipment),

such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet cable.

ETHERNET

Wing Nuts (Qty.3)Washers (Qty.3) M3×30 Pan-head Screws (Qty.3)

Connect the Ethernet cable to the

ETHERNET port. Attach the EAP to the

mounting bracket by aligning the arrow

mark on the EAP with the arrow mark

on the mounting bracket, then rotate the

EAP until it locks into place, as shown on

the left.

Note: Make sure that the ceiling tile is bigger than the EAP.

EAPEAP EAP

Switch

Router

Internet

Clients

EAP Controller

Drill Hole for Ethernet cable

The port is used to connect to the provided power adapter to power the EAP. The other end of the power

adapter connects to a standard electrical wall outlet.

POWER (for EAP115 only)

Note: EAP115 is used as an example throughout this guide. Other models may dier in appearance.

Summary of content (2 pages)

PAGE 1
Typical Network Topology Option 1: Ceiling Mounting Note: Make sure that the ceiling tile is bigger than the EAP. Internet Quick Installation Guide Washers (Qty.3) Wireless Access Point EAP110/EAP115/EAP225 M3×30 Pan-head Screws (Qty.3) Router Wing Nuts (Qty.3) 1 Remove the ceiling tile. Switch Note: EAP115 is used as an example throughout this guide. Other models may differ in appearance. X3 LED Indication EAP Controller PC Solid Green The device is working properly.
PAGE 2
Option 2: Wall Mounting Note: For security reasons, it is recommended not to install the EAP with the louver downward. M3×28 Plastic Wall Anchors (Qty.3) Tip (for EAP225 only) To remove the EAP from the mounting bracket, insert a paper clip in the Security Slot to release the Locking Tab and rotate the EAP until it is detached from the mounting bracket, as shown below. Locking Tab M3×20 Self-tapping Screws (Qty.