Whole Home Mesh Wi-Fi System Seamless Roaming | Parental Controls | Adaptive Path Selection User Guide AC1200 Whole Home Mesh Wi-Fi Add-On Unit Deco M3W 1910012488 REV1.0.
Contents About This Guide····················································· 1 Appearance································································ 2 Set Up Your Deco Extender······························· 3 Dashboard··································································· 5 Update Deco Units················································· 6 Authentication··························································· 7
About This Guide This guide provides a brief introduction to Deco Whole Home Mesh Wi-Fi Add-On Unit and the Deco app, as well as regulatory information. Please note that features of Deco Extenders may vary slightly depending on the model and software version you have, and on your location, language and internet service provider. All images, parameters and descriptions documented in this guide are used for demonstration only.
Appearance Deco Extender has four LED lights and a Reset button. See the explanation below: Plug: Connect to a standard power socket. Note: 1. The provided plug may differ from the picture due to different regional power specifications. 2. For safety, only plug the extender in upright direction as shown on the right. Reset Button: Press to reset Deco Extender to factory default settings. LEDs: LED STATUS Power Pulse Signal On/Off White Solid Red Solid White Pulse Red Pulse 2.
Set Up Your Deco Extender Follow the steps below to add the Deco Extender to your existing Deco network. This guide uses Deco M4R as an example for main Deco. 1. Connect to Deco Wi-Fi Connect your smartphone to your existing Deco Wi-Fi, then launch the Deco app. Note: If you have not set up a Deco Wi-Fi, refer to the user manual of your Deco Whole Home Mesh Wi-Fi System/Unit. 2. Add your Deco Extender On the dashboard, tap + and select DECOS. Identify your Deco model. 3.
4. Plug in your Deco Extender Plug the Deco Extender into a wall outlet and wait until its Power LED turns solid on. The app will automatically find the device. Tips: If you have multiple Deco Extenders, you can plug in and set them up together. 5. Specify the location Select a location for the Deco Extender. If its location is not listed, you can create a new one by choosing Custom. 6. Finish The Deco app will automatically optimize your Deco network and finish adding the Deco Extender.
Dashboard After you successfully extend your Deco network, you will see the dashboard of the Deco app. Here you can view the connected devices and their (Internet) icon to check the working status of all Deco units.
Update Deco Units TP-Link is dedicated to improving product features and providing a better customer experience. Update Deco units when prompted in the Deco app.
Authentication COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-Link Technologies Co., Ltd. Copyright © 2019 TP-Link Technologies Co.
FCC compliance information statement Product Name: AC1200 Whole Home Mesh Wi-Fi Add-On Unit Model Number: Deco M3W Responsible Party: TP-Link USA Corporation, d/b/a TP-Link North America, Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: http://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6803 E-mail: sales.usa@tp-link.com This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. OPERATING FREQUENCY (the maximum transmitted power) 2400 MHz -2483.
Canadian Compliance Statement This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1.
Déclaration d’exposition aux radiations: Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Industry Canada Statement CAN ICES-3 (B)/NMB-3(B) Korea Warning Statements 해당 무선설비는 운용중 전파혼신 가능성이 있음.
限用物質含有情況標示聲明書 限用物質及其化學符號 鉛 鎘 汞 六價鉻 多溴聯苯 多溴二苯醚 Pb Cd Hg CrVI PBB PBDE ○ ○ ○ ○ ○ ○ 外殼 ○ ○ ○ ○ ○ ○ 電源供應板 − ○ ○ ○ ○ ○ 產品元件名 稱 PCB 備考1. "超出0.1 wt %" 及 "超出0.01 wt %" 系指限用物質之百分比含量超出百分比 含量基準值。 備考2. "○"系指該項限用物質之百分比含量未超出百分比含量基準值。 備考3. " − " 系指該項限用物質為排除項目。 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.
Explanations of the symbols on the product label Symbol Explanation Class II equipment AC voltage Indoor use only RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
