User Guide AC4000 MU-MIMO Tri-Band Wi-Fi Router Archer C4000 REV3.0.
Contents About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Chapter 1. Get to Know About Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1. 1. 1. 2. Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7. 1. Access the USB Storage Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 7. 1. 1.Access the USB Device Locally . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 7. 1. 2.Access the USB Device Remotely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 7. 2. 7. 3. 7. 1. 3.Customize the Access Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Media Sharing . . .
12. 8. 2.Connect via the Router’s PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 12. 8. 3.Connect via the Client’s PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 12. 9. Schedule Your Wireless Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Chapter 13. Manage the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 13. 1. 13. 2. 13. 3. 13. 4. 13.
About This Guide This guide is a complement of Quick Installation Guide. The Quick Installation Guide instructs you on quick internet setup, and this guide provides details of each function and shows you the way to configure these functions appropriate to your needs. When using this guide, please notice that features of the router may vary slightly depending on the model and software version you have, and on your location, language, and internet service provider.
Speed/Coverage Disclaimer *Maximum wireless signal rates are the physical rates derived from IEEE Standard 802.11 specifications.
Chapter 1 Get to Know About Your Router This chapter introduces what the router can do and shows its appearance.
Chapter 1 1. 1. Product Overview The TP-Link router is designed to fully meet the need of Small Office/Home Office (SOHO) networks and users demanding higher networking performance. The powerful antennas ensure continuous Wi-Fi signal to all your devices while boosting widespread coverage throughout your home, and the built-in Ethernet ports supply high-speed connection to your wired devices.
Chapter 1 Item Description Reset Button Press this button for more than 5 seconds to reset the router to its factory default settings. Power On/Off Button Press this button for 1 second to power on or off the router. Power Port For connecting the router to power socket via the provided power adapter. Antennas Used for wireless operation and data transmit. Upright them for the best WiFi performance. 1. 2. 2.
Chapter 1 Name Status Indication On/Off This light remains on for 5 minutes when a WPS connection is established, then turns off. (WPS) Flashing On (USB) Flashing Off WPS connection is in progress. This may take up to 2 minutes. The inserted USB device is ready to use. A USB device is being identified. No device is plugged into the USB port.
Chapter 2 Connect the Hardware This chapter contains the following sections: • Position Your Router • Connect Your Router
Chapter 2 2. 1. Position Your Router • The product should not be located in a place where it will be exposed to moisture or excessive heat. • Place the router in a location where it can be connected to multiple devices as well as to a power source. • Make sure the cables and power cord are safely placed out of the way so they do not create a tripping hazard. • The router can be placed on a shelf or desktop.
Chapter 2 3. Connect the modem to your router’s Internet port with an Ethernet cable. 4. Turn on the modem, and then wait about 2 minutes for it to restart. 5. Connect the power adapter to the router and turn on the router. 6. Confirm that the following LEDs are on and solid to verify the hardware is connected correctly. Power On 2.4GHz On 5GHz-1 On 5GHz-2 On Internet On Note: for about 1 second, and then check the LEDs again.
Chapter 2 • Method 3: Use the WPS button Wireless devices that support WPS, including Android phones, tablets, and most USB network cards, can be connected to your router through this method. Note: • WPS is not supported by iOS devices. • The WPS function cannot be configured if the wireless function of the router is disabled. Also, the WPS function will be disabled if your wireless encryption is WEP.
Chapter 3 Log In to Your Router
Chapter 3 Log In to Your Router With a web-based utility, it is easy to configure and manage the router. The web-based utility can be used on any Windows, Mac OS or UNIX OS with a web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. Follow the steps below to log in to your router. 1. Set up the TCP/IP Protocol in Obtain an IP address automatically mode on your computer. 2. Visit http://tplinkwifi.net, and create a login password for secure management purposes.
Chapter 4 Set Up Internet Connection This chapter introduces how to connect your router to the internet. The router is equipped with a web-based Quick Setup wizard. It has necessary ISP information built in, automates many of the steps and verifies that those steps have been successfully completed. Furthermore, you can also set up an IPv6 connection if your ISP provides IPv6 service.
Chapter 4 4. 1. Set Up Internet Connection Use Quick Setup Wizard The Quick Setup Wizard will guide you to set up your router. Tips: If you need the IPv6 internet connection, please refer to the section of Set Up an IPv6 Internet Connection. Follow the steps below to set up your router. 1. Visit http://tplinkwifi.net, and log in with the password you set for the router. 2. Click Quick Setup on the top of the page. Then follow the step-by-step instructions to connect your router to the internet. 3.
Chapter 4 Set Up Internet Connection Note: If you are unsure of what your connection type is, click Auto Detect. Since different connection types require different cables and connection information, you can also refer to the demonstrations in Step 4 to determine your connection type. 4. Follow the instructions on the page to continue the configuration. Parameters on the figures are just used for demonstration. 1 ) If you choose Dynamic IP, you need to select whether to clone the MAC address.
Chapter 4 Set Up Internet Connection 3 ) If you choose PPPoE, enter the Username and Password provided by your ISP. PPPoE users usually have DSL cable modems. 4 ) If you choose L2TP, enter the Username and Password and choose the Secondary Connection provided by your ISP. Different parameters are needed according to the Secondary Connection you have chosen.
Chapter 4 Set Up Internet Connection 5 ) If you choose PPTP, enter the Username and Password, and choose the Secondary Connection provided by your ISP. Different parameters are needed according to the Secondary Connection you have chosen. 5. Click Save. 6. To check your internet connection, click Network Map on the left of the page. After the connection succeeds, the screen will display as follows. Here we take Dynamic IP as an example.
Chapter 4 Set Up Internet Connection Note: It may take 1-2 minutes to make the settings valid. Tips: • If your internet connection type is BigPond Cable, please go to Advanced > Network > Internet to set your router. • If you use Dynamic IP and PPPoE and you are provided with any other parameters that are not required on the page, please go to Advanced > Network > Internet to complete the configuration. • If you still cannot access the internet, refer to the FAQ section for further instructions. 4. 3.
Chapter 4 Set Up Internet Connection 3. After rebooting, connect the router to your existing wired router via an Ethernet cable. 4. Connect to the Wi-Fi of the router and log in again to the web management page http://tplinkwifi.net, and click Quick Setup. 5. Configure your wireless settings and click Next. 6. Confirm the information and click Save. Now, you can enjoy Wi-Fi.
Chapter 4 Set Up Internet Connection Tips: Functions, such as Parental Controls, Qos and NAT Forwarding, are not supported in the Access Point mode. 4. 4. Set Up an IPv6 Internet Connection Your ISP provides information about one of the following IPv6 internet connection types: PPPoE, Dynamic IP(SLAAC/DHCPv6), Static IP, 6to4 tunnel, Pass-Through (Bridge). 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > IPv6. 3.
Chapter 4 Set Up Internet Connection 2 ) Dynamic IP (SLAAC/DHCPv6): Click Advanced to input further information if your ISP requires. Click Save. 3 ) PPPoE: By default, the router uses the IPv4 account to connect to the IPv6 server. Click Advanced to input further information if your ISP requires. Click Save and then click Connect.
Chapter 4 Set Up Internet Connection 4 ) 6to4 Tunnel: An IPv4 internet connection type is a prerequisite for this connection type (Manually Set Up Your Internet Connection). Click Advanced to input further information if your ISP requires. Click Save and then click Connect. 5 ) Pass-Through (Bridge): Click Save and skip to Step 6.
Chapter 4 Set Up Internet Connection 5. Configure LAN ports. Windows users are recommended to choose from the first two types. Fill in Address Prefix provided by your ISP, and click Save. Tips: Find Help on the web management page to know more about items. 6. Click Status to check whether you have successfully set up an IPv6 connection. The following figure is an example of a successful PPPoE configuration. Tips: Visit the FAQ section if there is no internet connection. 4. 5.
Chapter 4 Set Up Internet Connection 4. Connect the router’s WAN port and LAN1 port to your modem’s two WAN ports with two Ethernet cables.
Chapter 5 TP-Link Cloud Service TP-Link Cloud service provides a better way to manage your cloud devices. Log in to your router with a TP-Link ID, and you can easily monitor and manage your home network when you are out and about via the Tether app. To ensure that your router stays new and gets better over time, the TP-Link Cloud will notify you when an important firmware upgrade is avaliable. Surely you can also manage multiple TP-Link Cloud devices with a single TP-Link ID.
Chapter 5 5. 1. TP-Link Cloud Service Register a TP-Link ID If you have skipped the registration during the Quick Setup process, you can: 1. Visit http://tplinkwifi.net, and log in with the password you set for the router. 2. Go to Basic > TP-Link Cloud. 3. Click Register Now and follow the instructions to register a TP-Link ID. 4. After activating your TP-Link ID, come back to the TP-Link Cloud page to log in.
Chapter 5 • TP-Link Cloud Service To change your password: 1. Click behind the Password. 2. Enter the current password, then a new password twice. And click Save. 5. 3. Manage the User TP-Link IDs The TP-Link ID used to log in to the router for the first time will be automatically bound as the Admin account. An admin account can add or remove other TP-Link IDs to or from the same router as Users.
Chapter 5 TP-Link Cloud Service • Add/remove other TP-Link IDs to/from the router. 5. 3. 1. Add TP-Link ID to Manage the Router 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID. 2. Go to Basic > TP-Link Cloud, and focus on the Bound Accounts section. 3. Click , enter another TP-Link ID as needed and click Save. Note: If you need another TP-Link ID, please register a new one via the Tether app.
Chapter 5 5. 4. TP-Link Cloud Service Manage the Router via the TP-Link Tether App The Tether app runs on iOS and Android devices, such as smartphones and tablets. 1. Launch the Apple App Store or Google Play store and search “TP-Link Tether” or simply scan the QR code to download and install the app. OR 2. Connect your device to the router’s wireless network. 3. Launch the Tether app, select the model of your router and log in with your TP-Link ID or the password you set for the router. 4.
Chapter 6 Guest Network This function allows you to provide Wi-Fi access for guests without disclosing your main network. When you have guests in your house, apartment, or workplace, you can create a guest network for them. In addition, you can customize guest network options to ensure network security and privacy.
Chapter 6 6. 1. Guest Network Create a Network for Guests 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > Guest Network. Locate the Wireless section. 3. Create a guest network as needed. 1 ) Tick the Enable Guest Network checkbox for the 2.4GHz/5GHz-1/5GH-2 wireless network. 2 ) Customize the SSID. Don‘t select Hide SSID unless you want your guests to manually input the SSID for guest network access.
Chapter 6 Guest Network specify a web link so that the newly connected guest will be redirected to, for example, the official website of your shop. 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > Guest Network. Locate the Wireless section. 3. Select Portal for Security. 4. Select the Authentication Type. • Simple Password – Specify a password for authentication (8-16 alphanumeric or “_” characters are allowed).
Chapter 6 Guest Network 3. Customize guest network options according to your needs. • Allow Guests to Access Each Other Tick this checkbox if you want to allow the wireless clients on your guest network to communicate with each other via methods such as network neighbors, Samba, Ping and FTP.
Chapter 7 USB Settings This chapter describes how to use the USB ports to share files, media from the USB storage devices over your home network locally, or remotely through the internet. The router supports USB external flash drives and hard drives.
Chapter 7 7. 1. USB Settings Access the USB Storage Device Insert your USB storage device into the router’s USB port and then access files stored there locally or remotely. Tips: • If you use USB hubs, make sure no more than 4 devices are connected to the router. • If the USB storage device requires using bundled external power, make sure the external power has been connected. • If you use a USB hard drive, make sure its file system is FAT32, exFat, NTFS or HFS+.
Chapter 7 USB Settings Open the Windows Explorer (or go to Computer) and type the server address \\tplinkwifi.net or ftp://tplinkwifi.net in the address bar, then press Enter. Windows computer 1 ) Select Go > Connect to Server. 2 ) Type the server address smb://tplinkwifi.net. 3 ) Click Connect. Mac 4 ) When prompted, select the Guest radio box. (If you have set up a username and a password to deny anonymous access to the USB disks, you should select the Registered User radio box.
Chapter 7 USB Settings • Share photos and other large files with your friends without logging in to (and paying for) a photo-sharing site or email system. • Get a safe backup for the materials for a presentation. • Remove the files on your camera’s memory card from time to time during the journey. Note: If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.x), you cannot use this feature because private addresses are not routed on the Internet.
Chapter 7 USB Settings 1 ) Open the Windows Explorer (or go to Computer, only for Windows users) or open a web browser. 2 ) Type the server address in the address bar: Type in ftp://: (such as ftp://59.40.2.243:21). If you have specified the domain name of the router, you can also type in ftp://: (such as ftp://MyDomainName:21) Computer 3 ) Press Enter on the keyboard.
Chapter 7 USB Settings 2. Now you can access the USB disk by visiting \\MyShare (for Windows) or smb:// MyShare (for Mac). • To only share specific content: 1. Focus on the Sharing Contents and Security section. Click the sharing folders and click Save. button to specify 2. Decide the way you share the folder: • Access Authentication: Tick to enable access authentication for sharing folders, and you will be required to log in to the Sharing Account to access the USB disk.
Chapter 7 • USB Settings To set up authentication for data security: You can set up authentication for your USB device so that network clients will be required to enter username and password when accessing the USB disk. In the Sharing Contents and Security part, enable Access Authentication. The default accounts are admin and visit. Click to customize the username and a password. Note: For Windows users, do not set the sharing username the same as the Windows username.
Chapter 7 USB Settings • Go to Computer > Network, then click the Media Server Name (Model number-share by default) in the Media Devices section. Note: Here we take Windows 7 as an example. Windows Computer Tablet • Use a third-party DLNA-supported player.
Chapter 7 7. 3. USB Settings Time Machine Time Machine backs up all files on your Mac computer to a USB storage device connected to your router. 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > USB Sharing > Time Machine. 3. Tick the checkbox to enable Time Machine. 4. Click Select to select a location for Time Machine backups. 5. Set the Size Limit for Backups. Note: 0 means no limit for the space. 6. Click Save.
Chapter 8 HomeCare – Parental Controls, QoS, Antivirus TP-Link HomeCareTM powered by Trend MicroTM provides a kit of features to help you create a personalized network that caters for the whole family. You can ensure appropriate internet access for everyone with Parental Controls, save bandwidth for the things that matter with QoS and keep your network secure with built-in Antivirus.
Chapter 8 8. 1. HomeCare – Parental Controls, QoS, Antivirus Parental Controls Parental Controls allows you to set up unique restrictions on internet access for each member of your family. You can block inappropriate content, set daily limits for the total time spent online and restrict internet access to certain times of the day. 8. 1. 1.
Chapter 8 HomeCare – Parental Controls, QoS, Antivirus 3 ) Select the devices that belong to this family member. Access restrictions will be applied to these devices. Click Add when finished. Note: Only devices that have previously been connected to your router’s network are listed here. If you are unable to find the device you want to add, connect it to your network and then try again. 4 ) Click Next. 5. Block content for this profile.
Chapter 8 HomeCare – Parental Controls, QoS, Antivirus 1 ) Select a filter level based on the age of the family member this profile belongs to. Blocked content will then be displayed in the Filter Content list. 2 ) If needed, you can edit the blocked content by clicking and between the Filter Content and Available Categories lists. to move categories 3 ) You can also block a specific website or application by clicking next to Filter Content.
Chapter 8 HomeCare – Parental Controls, QoS, Antivirus 1 ) Enable Time Limits on Monday to Friday and Saturday & Sunday then set the allowed online time to 2 hours each day. 2 ) Enable Bed Time on Monday to Friday and use the up/down arrows or enter times in the fields. Devices under this profile will be unable to access the internet during this time period. 3 ) Click Save. Done! The amount of time your child spends online is controlled and inappropriate content is blocked on their devices. 8. 1. 2.
Chapter 8 HomeCare – Parental Controls, QoS, Antivirus 2. Go to Basic > HomeCare > Parental Controls or Advanced > Parental Controls. 3. Find the correct profile and click in the Insights column. Note: If you have not set up a profile for your child yet, you should do that first by clicking , then follow the steps to create a profile. Refer to Scenario 1: Setting Up Access Restrictions for detailed instructions. 4.
Chapter 8 HomeCare – Parental Controls, QoS, Antivirus 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Basic > HomeCare > QoS or Advanced > QoS. 3. In the Application Priority tab, click Gaming to prioritize this online activity. The default is Standard, with no application prioritized. 4. In the Device Priority tab, find your computer and toggle on Priority.
Chapter 8 HomeCare – Parental Controls, QoS, Antivirus • Intrusion Prevention System Identifies and blocks potential threats from attackers and fixes vulnerabilities in the network. • Infected Device Quarantine Prevents infected devices from sending your sensitive information to clients outside your network or spreading security threats. • To access your router’s Antivirus settings: 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2.
Chapter 9 Network Security This chapter guides you on how to protect your home network from cyber attacks and unauthorized users by implementing these three network security functions. You can protect your home network against DoS (Denial of Service) attacks from flooding your network with server requests using DoS Protection, block or allow specific client devices to access your network using Access Control, or you can prevent ARP spoofing and ARP attacks using IP & MAC Binding.
Chapter 9 9. 1. Network Security Protect the Network from Cyber Attacks The SPI (Stateful Packet Inspection) Firewall protects the router from cyber attacks and validate the traffic that is passing through the router based on the protocol. This function is enabled by default. 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > Security > Firewall. It’s recommended to keep the default settings.
Chapter 9 Network Security 2 ) Select the device(s) to be blocked in the Online Devices table by ticking the checkbox(es). 3 ) Click Block above the Online Devices table. The selected devices will be added to Devices in Blacklist automatically. To allow specific device(s): 1 ) Select Whitelist and click Save. 2 ) Click Add in the Devices in Whitelist section.
Chapter 9 Network Security 9. 3. IP & MAC Binding IP & MAC Binding, namely, ARP (Address Resolution Protocol) Binding, is used to bind network device’s IP address to its MAC address. This will prevent ARP Spoofing and other ARP attacks by denying network access to an device with matching IP address in the Binding list, but unrecognized MAC address. I want to: Prevent ARP spoofing and ARP attacks. How can I do that? 1. Visit http://tplinkwifi.
Chapter 9 Network Security Done! Now you don’t need to worry about ARP spoofing and ARP attacks! 55
Chapter 10 NAT Forwarding The router’s NAT (Network Address Translation) feature makes devices on the LAN use the same public IP address to communicate with devices on the internet, which protects the local network by hiding IP addresses of the devices. However, it also brings about the problem that an external host cannot initiatively communicate with a specified device on the local network.
Chapter 10 NAT Forwarding 10. 1. Share Local Resources on the Internet by Virtual Servers When you build up a server on the local network and want to share it on the internet, Virtual Servers can realize the service and provide it to internet users. At the same time Virtual Servers can keep the local network safe as other services are still invisible from the internet. Virtual Servers can be used for setting up public services on your local network, such as HTTP, FTP, DNS, POP3/SMTP and Telnet.
Chapter 10 NAT Forwarding Tips: • It is recommended to keep the default settings of Internal Port and Protocol if you are not clear about which port and protocol to use. • If the service you want to use is not in the Service Type, you can enter the corresponding parameters manually. You should verify the port number that the service needs. • You can add multiple virtual server rules if you want to provide several services in a router. Please note that the External Port should not be overlapped.
Chapter 10 NAT Forwarding 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > NAT Forwarding > Port Triggering and click Add. 3. Click View Existing Applications, and select the desired application. The Triggering Port, External Port and Protocol will be automatically filled in. The following picture takes application MSN Gaming Zone as an example. 4. Click OK.
Chapter 10 NAT Forwarding Note: When DMZ is enabled, the DMZ host is totally exposed to the internet, which may bring some potential safety hazards. If DMZ is not in use, please disable it in time. I want to: Make the home PC join the internet online game without port restriction. For example, due to some port restriction, when playing the online games, you can login normally but cannot join a team with other players. To solve this problem, set your PC as a DMZ host with all ports open.
Chapter 10 NAT Forwarding Tips: • UPnP is enabled by default in this router. • Only the application supporting UPnP protocol can use this feature. • UPnP feature needs the support of operating system (e.g. Windows Vista/ Windows 7/ Windows 8, etc. Some of operating system need to install the UPnP components).
Chapter 11 VPN Server The VPN (Virtual Private Networking) Server allows you to access your home network in a secured way through internet when you are out of home. The router offers two ways to setup VPN connection: OpenVPN and PPTP (Point to Point Tunneling Protocol) VPN. OpenVPN is somewhat complex but with greater security and more stable. It is suitable for restricted environment, such as campus network and company intranet.
Chapter 11 VPN Server 11. 1. Use OpenVPN to Access Your Home Network In the OpenVPN connection, the home network can act as a server, and the remote device can access the server through the router which acts as an OpenVPN Server gateway. To use the VPN feature, you should enable OpenVPN Server on your router, and install and run VPN client software on the remote device. Please follow the steps below to set up an OpenVPN connection. Step1. Set up OpenVPN Server on Your Router 1. Visit http://tplinkwifi.
Chapter 11 VPN Server 6. Select your Client Access type. Select Home Network Only if you only want the remote device to access your home network; select Internet and Home Network if you also want the remote device to access internet through the VPN Server. 7. Click Save. 8. Click Generate to get a new certificate. Note: If you have already generated one, please skip this step, or click Generate to update the certificate. 9.
Chapter 11 VPN Server Note: Before you enable VPN Server, we recommend you configure Dynamic DNS Service (recommended) or assign a static IP address for router’s WAN port and synchronize your System Time with internet. 3. In the Client IP Address filed, enter the range of IP addresses (up to 10) that can be leased to the devices by the PPTP VPN server. 4. Click Advanced to set the PPTP connection permission according to your needs.
Chapter 11 VPN Server 2 ) Enter the Username and Password to authenticate devices to the PPTP VPN Server. 3 ) Click OK. Step 2. Configure PPTP VPN Connection on Your Remote Device The remote device can use the Windows built-in PPTP software or a third-party PPTP software to connect to PPTP Server. Here we use the Windows built-in PPTP software as an example. 1. Go to Start > Control Panel > Network and Internet > Network and Sharing Center. 2. Select Set up a new connection or network. 3.
Chapter 11 VPN Server 4. Select Use my Internet connection (VPN). 5. Enter the internet IP address of the router (for example: 218.18.1.73) in the Internet address field. Click Next.
Chapter 11 VPN Server 6. Enter the User name and Password you have set for the PPTP VPN server on your router, and click Connect. 7. The PPTP VPN connection is created and ready to use.
Chapter 11 VPN Server 69
Chapter 12 Customize Your Network Settings This chapter guides you on how to configure advanced network features.
Chapter 12 Customize Your Network Settings 12. 1. Change the LAN Settings The router is preset with a default LAN IP 192.168.0.1, which you can use to log in to its web management page. The LAN IP address together with the Subnet Mask also defines the subnet that the connected devices are on. If the IP address conflicts with another device on your local network or your network requires a specific IP subnet, you can change it. 1. Visit http://tplinkwifi.
Chapter 12 Customize Your Network Settings 4. Specify two ports for Link Aggregation. Note: LAN ports used for IPTV or WAN aggregation cannot be selected. 5. Click Save. 12. 3. Configure to Support IPTV Service I want to: Configure IPTV setup to enable Internet/IPTV/Phone service provided by my internet service provider (ISP). How can I do that? 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > Network > IPTV. 3.
Chapter 12 Customize Your Network Settings 2 ) Click Save. 3 ) After configuring IGMP proxy, IPTV can work behind your router now. You can connect your set-top box to any of the router’s Ethernet port. If IGMP is not the technology your ISP applies to provide IPTV service: 1 ) Tick Enable IPTV. 2 ) Select the appropriate Mode according to your ISP. • Select Bridge if your ISP is not listed and no other parameters are required. • Select Custom if your ISP is not listed but provides necessary parameters.
Chapter 12 Customize Your Network Settings 1. Tick the Enable DHCP Server checkbox. 2. Enter the starting and ending IP addresses in the IP Address Pool. 3. Enter other parameters if the ISP offers. The Default Gateway is automatically filled in and is the same as the LAN IP address of the router. 4. Click Save. • To reserve an IP address for a specified client device: 1. Click Add in the Address Reservation section. 2. Click View Exsiting Devices or enter the MAC address of the client device. 3.
Chapter 12 Customize Your Network Settings 12. 5. Set Up a Dynamic DNS Service Account Most ISPs assign a dynamic IP address to the router and you can use this IP address to access your router remotely. However, the IP address can change from time to time and you don’t know when it changes. In this case, you might apply the DDNS (Dynamic Domain Name Server) feature on the router to allow you and your friends to access your router and local servers (FTP, HTTP, etc.
Chapter 12 Customize Your Network Settings If you have selected NO-IP or DynDNS, enter the username, password and domain name of your account. 5. Click Login and Save. Tips: If you want to use a new DDNS account, please click Logout first, and then log in with a new account. 12. 6. Create Static Routes Static routing is a form of routing that is configured manually by a network administrator or a user by adding entries into a routing table.
Chapter 12 Customize Your Network Settings Router A Company’s server Router B WAN: 172.30.30.100 LAN: 192.168.0.1 LAN: 192.168.0.2 172.30.30.1 Switch PC 192.168.0.100 How can I do that? 1. Change the routers’ LAN IP addresses to two different IP addresses on the same subnet. Disable Router B’s DHCP function. 2. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for Router A. 3. Go to Advanced > Network > Static Routing. 4.
Chapter 12 Customize Your Network Settings subnet mask of the corresponding network IP. In the example, the destination network is a single IP, so here enter 255.255.255.255. Default Gateway: The IP address of the gateway device to which the data packets will be sent. This IP address must be on the same subnet with the router’s IP which sends out data. In the example, the data packets will be sent to the LAN port of Router B and then to the Server, so the default gateway should be 192.168.0.2.
Chapter 12 Customize Your Network Settings 2. Create a new SSID in Network Name (SSID) and customize the password for the network in Password. The value is case-sensitive. Note: If you change the wireless settings with a wireless device, you will be disconnected when the settings are effective. Please write down the new SSID and password for future use. • To hide SSID: 1. Go to Basic > Wireless. 2.
Chapter 12 • Customize Your Network Settings To enable the Airtime Fairness feature: The Airtime Fairness feature can improve the overall network performace by sacrificing a little bit of network time on your slow devices. Enable Airtime Fairness when you wish to sacrifice some of the networking time from the slow devices, so that your faster devices can achieve better quality of service.
Chapter 12 • • Customize Your Network Settings Note: If you want to enable/disable the WPS feature, go to System Tools > System Parameters > WPS, tick or untick the Enable WPS checkbox. PIN (Personal Identification Number) is an eight-character identification number preset to each router. WPS supported devices can connect to your router with the PIN. The default PIN is printed on the label of the router. 12. 8. 3. Connect via the Client’s PIN Enter the PIN of your device and click Connect.
Chapter 12 • • Customize Your Network Settings Note: The Effective Time Schedule is based on the time of the router. You can go to Advanced > System Tools > Time Settings to modify the time. The wireless network will be automatically turned on after the time period you set.
Chapter 13 Manage the Router This chapter will show you the configuration for managing and maintaining your router.
Chapter 13 Manage the Router 13. 1. Set Up System Time System time is the time displayed while the router is running. The system time you configure here will be used for other time-based functions like Parental Controls. You can choose the way to obtain the system time as needed. 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > System Tools > Time Settings. • To get time from the internet: 1.
Chapter 13 Manage the Router 2. The time of your computer will then be displayed and click Save. • To manually set the date and time: 1. In the Set Time field, select Manually. 2. Set the current Date (In MM/DD/YYYY format). 3. Set the current Time (In HH/MM/SS format). 4. Click Save. • To set up Daylight Saving Time: 1. Select Enable Daylight Saving Time.
Chapter 13 Manage the Router 2. Select the correct Start date and time when daylight saving time starts at your local time zone. 3. Select the correct End date and time when daylight saving time ends at your local time zone. 4. Click Save. 13. 2. Control the LED The LED of the router indicates its activities and status. You can enable the Night Mode feature to specify a time period during which the LED is off. 1. Visit http://tplinkwifi.
Chapter 13 Manage the Router 2. Go to Advanced > System Tools > Diagnostics. 3. Enter the information with the help of page tips: 1 ) Choose Ping or Traceroute as the diagnostic tool to test the connectivity; • Ping is used to test the connectivity between the router and the tested host, and measure the round-trip time. • Traceroute is used to display the route (path) your router has passed to reach the tested host, and measure transit delays of packets across an Internet Protocol network.
Chapter 13 Manage the Router 13. 4. Test Your Internet Speed Speed Test provides an easy way to monitor your network speed. It reveals the current upload and download speeds received from your provider and gives practical advice about the activities you can enjoy. • To test your internet speed: 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Basic > Network Map and click . 3.
Chapter 13 Manage the Router 13. 5. Upgrade the Firmware TP-Link aims at providing better network experience for users. We will inform you through the web management page if there’s any update firmware available for your router. Also, the latest firmware will be released at the TP-Link official website www.tp-link.com, and you can download it from the Support page for free. • • • Note: Make sure you remove all attached USB devices from the router before the firmware upgrade to prevent data loss.
Chapter 13 Manage the Router 4. Wait a few minutes for the upgrade and reboot to complete. Tips: If there’s a new and important firmware update for your router, you will see the notification (similar as shown below) on your computer as long as a web browser is opened. Click Upgrade Now, and log into the web management page with the username and password you set for the router. You will see the Firmware Upgrade page. 13. 5. 2. Local Upgrade 1. Download the latest firmware file for the router from www.
Chapter 13 Manage the Router a previous settings from the backup file when needed. Moreover, if necessary you can erase the current settings and reset the router to the default factory settings. 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > System Tools > Backup & Restore. • To backup configuration settings: Click Backup to save a copy of the current settings to your local computer. A ‘.
Chapter 13 Manage the Router 2. Wait a few minutes for the resetting and rebooting. Note: • During the resetting process, do not turn off or reset the router. • We strongly recommend you backup the current configuration settings before resetting the router. 13. 7. Set the Router to Reboot Regularly The Scheduled Reboot feature cleans the cache to enhance the running performance of the router. 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2.
Chapter 13 Manage the Router 2. Go to Advanced > System Tools > Administration and focus on the Account Management section. 3. Enter the old password, then a new password twice (both case-sensitive). Click Save. 4. Use the new password for future logins. 13. 9. Default Password Recovery This feature allows you to recover the login password without restoring router. Note: If you are using a TP-Link ID to log in to the web management page, the Default Password Recovery feature will be disabled.
Chapter 13 Manage the Router 5. Click Save. You can click Test Email to test whether the configuration is successful. To recover the login password, please visit http://tplinkwifi.net, click Forgot Password? on the login page and follow the instructions to set a new password. 13. 10. Local Management This feature allows you to limit the number of client devices on your LAN from accessing the router by using the MAC address-based authentication. 1. Visit http://tplinkwifi.
Chapter 13 • Manage the Router Allow specific devices to manage the router: 1. Toggle off Access for All LAN Connected Devices. 2. Click Add. 3. Click Scan and select the device to manage the router from the Existing Devices list, or enter the MAC address of the device manually. 4. Specify a Description for this entry. 5. Tick the Enable This Entry checkbox and click OK. 13. 11. Remote Management This feature allows you to control remote devices’ authority to manage the router. 1.
Chapter 13 Manage the Router 2. Use the default value HTTPS Port: 443 and HTTP Port: 80 or enter values between 1024 and 65535. 3. Select All Devices in Remote Managers. 4. Click Save. • Allow Specified device to manage the router remotely: 1. Select Enable Remote Management. 2. Use the default value HTTPS Port: 443 and HTTP Port: 80 or enter values between 1024 and 65535. 3. Select Specified Devices in Remote Managers. 4. Enter IP address of the device in Only this IP address. 5. Click Save.
Chapter 13 • Manage the Router To send the system log to a mailbox at a fixed time: For example, I want to check my router’s working status at a fixed time every day, however, it’s too troublesome to log in to the web management page every time I want to go checking. It would be great if the system logs could be sent to my mailbox at 8 a.m. every day. 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > System Tools > System Log. 3.
Chapter 13 Manage the Router 2 ) To: Enter the recipient’s email address, which can be the same as or different from the sender’s email address. 3 ) SMTP Server: Enter the SMTP server address. Tips: SMTP server is available for users in most webmail systems. For example, the SMTP server address of Hotmail is smtp-mail.outlook.com. You can refer to their Help page to learn the SMTP server address. 4 ) Select Enable Authentication.
Chapter 13 Manage the Router 4. Check the total traffic statistics of each device on Traffic Monitor List. Click Refresh to update the statistic information on the page. Click Reset All to reset all statistic values in the list to zero. 13. 14. System Parameters 13. 14. 1. 2.4GHz/5GHz Wireless You can configure the parameters of traffic transmission rules in wireless networks. It’s recommended to keep the default settings if you are not sure of the proper ones in the case. 1. Visit http://tplinkwifi.
Chapter 13 Manage the Router • Bacon Interval - Enter a value between 40 and 1000 to determine the duration between beacon packets that are broadcasted by the router to synchronize the wireless network. The default is 100 milliseconds. • RTS Threshold – Enter a value between 1 and 2346 to determine the packet size of data transmission through the router. The default size is 2346.
Chapter 13 Manage the Router 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2. Go to Advanced > System Tools > System Parameters. Focus on 2.4GHz/5GHz WDS section. • To bridge a network by Survey/Scan feature: 1. Enable the WDS Bridging feature. 2. Click Survey to scan all available networks and select the network you want to bridge. The SSID (network name) and MAC Address will be automatically populated.
Chapter 13 Manage the Router 2. Go to Advanced > System Tools > System Parameters. Focus on NAT section. 3. NAT feature is enable by dafault and it’s highly recommended. If you disable it, you may have no access to the internet and NAT Forwarding will not take effect. 13. 14. 4.
Chapter 14 Work with Alexa and IFTTT This chapter will show you how to configure your router to work with Alexa and IFTTT.
Chapter 14 Work with Alexa and IFTTT Control your network devices using simply the power of your voice with the TP-Link Router Skill for Amazon. Prioritize the Internet connection of your laptop, switch off your router’s LED or ask Alexa to read out the password of the guest network, all without stopping what you’re doing. With IFTTT, you can trigger actions when devices are connecting, disconnecting, or being added to your network.
FAQ Q1. What should I do if I forget my wireless password? The default wireless password is printed on the label of the router. If the password has been altered: 1. Connect your computer to the router using an Ethernet cable. 2. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 3. Go to Basic > Wireless to retrieve or reset your wireless password. Q2.
4 ) Click LAN settings and deselect the following three options and click OK. 5 ) Go to Advanced > Restore advanced settings, click OK to save the settings.
• Use another web browser or computer to log in again. • Reset the router to factory default settings and try again. If login still fails, please contact the technical support. Note: You’ll need to reconfigure the router to surf the internet once the router is reset. Q4. What should I do if I can’t access the internet even though the configuration is finished? 1. Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router. 2.
• Your computer might not recognize any DNS server addresses. Please manually configure the DNS server. 1 ) Go to Advanced > Network > DHCP Server. 2 ) Enter 8.8.8.8 as Primary DNS, click Save. Tips: 8.8.8.8 is a safe and public DNS server operated by Google. • Restart the modem and the router. 1 ) Power off your modem and router, and leave them off for 1 minute. 2 ) Power on your modem first, and wait about 2 minutes until it gets a solid cable or Internet light. 3 ) Power on the router.
• Upgrade the firmware of the router. • Check the TCP/IP settings on the particular device if all other devices can get internet from the router. As the picture below shows, if the IP Address is 0.0.0.0, please try the methods below and try again: • Make sure the physical connection between the router and the modem is proper. • Clone the MAC address of your computer. 1 ) Visit http://tplinkwifi.net, and log in with your TP-Link ID or the password you set for the router.
• Modify the LAN IP address of the router. Note: Most TP-Link routers use 192.168.0.1/192.168.1.1 as their default LAN IP address, which may conflict with the IP range of your existing ADSL modem/router. If so, the router is not able to communicate with your modem and you can’t access the internet. To resolve this problem, we need to change the LAN IP address of the router to avoid such conflict, for example, 192.168.2.1. 1 ) Visit http://tplinkwifi.
6 ) Restart the modem and the router again. • Please upgrade the firmware of the router. If you’ve tried every method above but still cannot access the internet, please contact the technical support. Q5. What should I do if I can’t find my wireless network or I cannot connect the wireless network? If you fail to find any wireless network, please follow the steps below: • Make sure the wireless function of your device is enabled if you’re using a laptop with built-in wireless adapter.
3 ) Select and right click on My Computer on desktop, select Manage to open Computer Management window. 4 ) Expand Services and Applications > Services, find and locate Wireless Zero Configuration in the Services list on the right side. 5 ) Right click Wireless Zero Configuration, and then select Properties. 6 ) Change Startup type to Automatic, click on Start button and make sure the Service status is Started. And then click OK.
2 ) If you cannot find the PIN or PIN failed, you may choose Connecting using a security key instead, and then type in the Wireless Password/Network Security Key. 3 ) If it continues to show note of Network Security Key Mismatch, it is suggested to confirm the wireless password of your wireless router. Note: Wireless Password/Network Security Key is case sensitive.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-Link Technologies Co., Ltd. Copyright © 2019 TPLink Technologies Co., Ltd.
FCC compliance information statement Product Name: AC4000 MU-MIMO Tri-Band Wi-Fi Router Model Number: Archer C4000 Component Name I.T.E. Power Supply Model S050FU1200400 S048CV1200330 Responsible party: TP-Link USA Corporation, d/b/a TP-Link North America, Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: http://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6803 E-mail: sales.usa@tp-link.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
FCC compliance information statement Product Name: I.T.E. Power Supply Model Number: S050FU1200400/S048CV1200330 Responsible party: TP-Link USA Corporation, d/b/a TP-Link North America, Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: http://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6803 E-mail: sales.usa@tp-link.com This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. OPERATING FREQUENCY (the maximum transmitted power) 2400 MHz-2483.
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d’en compromettre le fonctionnement This radio transmitter (IC: 8853A-C4000/ Model: Archer C4000) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated.
3. Le gain maximal d’antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour l’exploitation point à point et non point à point. En outre, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d.
˙ 幢悦劥欴ㅷ⛓锞⯓䬫䱈ꨶ彂箁锞⺡⢪欽巊넓㑑ꪓ幢悦ⷭ䧴憈䋒鹎遤 幢悦 ˙ 岤䠑惐锞⺡㼟宐䧴Ⱖ➮巊넓悝扵ⵌ劥欴ㅷ♳ ˙ 䳄坵莅〡⣘鸒괐⢪欽⟃焷⥃劥欴ㅷ涸乽⡲〳ꬒ⚛姺麕攨锞⺡㜧㝱 䧴銼覈〡 ˙ 锞⺡㼟劥欴ㅷ縨佞倴ꬒ鵜攨彂涸㖒倰ꤑꬌ剤姻䌢涸鸒괐や♶〳佞㖈 㺙ꟗ⡙縨⚥ ˙ 锞♶銴猙荈䩧堥媽♶銴㎲鑑荈遤笞⥜劥欴ㅷ锞歋䱇奚涸㼠噠➃㡦鹎 遤姽갪䊨⡲ ꣳ欽暟颶わ剤䞕屣垦爚耫僈剅 ꣳ欽暟颶⿺Ⱖ⻊㷸痗贪 ꊋ ꓸ 寏 Ⱉ⭆ꋈ 㢴徃耡薅 㢴徃✳薅ꄍ 1$# 1C ӧ $E ӧ )H ӧ $S7* ӧ 1## ӧ 1#%& ӧ 㢪媽 ӧ ӧ ӧ ӧ ӧ ӧ ꨵ彂黟ꂁ㐼 ơ ӧ ӧ ӧ ӧ ӧ 欴ㅷ⯋⟝ぜ 珖 ⪓罌 馄ⴀ XU ⿺ 馄ⴀ XU 禹䭷ꣳ欽暟颶⛓涰ⴔ嫱ゎꆀ馄ⴀ涰ⴔ嫱 ゎꆀ㛇彋⧩ ⪓罌 ӧ 禹䭷鑪갪ꣳ欽暟颶⛓涰ⴔ嫱ゎꆀ劢馄ⴀ涰ⴔ嫱ゎꆀ㛇彋⧩ ⪓罌 ơ 禹䭷鑪갪ꣳ欽暟颶捀䱗ꤑ갪湡 цѧѥћѪѡѩ ѨќѧѩџѫѽѡѥљїѤѥ ўњѽћѤѥ Ѩ Ѧѧїљ
• Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don’t hesitate to contact us. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
