TD-8810 External ADSL2+ Router Rev: 1.1.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2008 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Package Contents The following items should be found in your package: ¾ ¾ ¾ ¾ ¾ ¾ ¾ One TD-8810 External ADSL2+ Router One AC power Adapter for TD-8810 External ADSL2+ Router One Resource CD for TD-8810 External ADSL2+ Router, including: • This Guide • Quick installation Guide Program • Other Helpful Information Quick installation Guide One RJ45 cable Two RJ11 cable One ADSL splitter ) Note: Make sure that the box contains the above items.
CONTENTS Chapter 1. Introduction ........................................................................................ 1 1.1 Product Overview ...................................................................................................... 1 1.2 Main Features ........................................................................................................... 1 1.3 Supporting protocol ...................................................................................................
TD-8810 External ADSL2+ Router User Guide Chapter 1. Introduction Thank you for choosing the TD-8810 External ADSL2+ Router. 1.1 Product Overview With the excellent circuit design and high quality production, we guarantee the ADSL Router’s high performance, great stability and easy to use. The TD-8810 uses integrated ADSL transceiver. The AFE supports full-rate ADSL connectivity conforming to the ITU and ANSI specifications.
TD-8810 External ADSL2+ Router User Guide - I.432 ATM physical layer compliant - Supports RFC2364 (PPPoA) - Supports RFC2516 (PPPoE) - Supports RFC1483 (EoA) (Bridged *and Router) - Supports RFC1577 (IPoA) ) Note: “*” needs the third-party software. 1.4 Transmit data-rate ¾ Max download data-rate: 24Mbps ¾ Max upload data-rate: 3.5Mbps ¾ Max line length: 6Km 1.
TD-8810 External ADSL2+ Router User Guide ADSL2+ Router without any explanations. Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation. You can set the parameters according to your demand.
TD-8810 External ADSL2+ Router User Guide Chapter 2. Hardware Installation The TD-8810 maintains three separate interfaces, one Ethernet, one ADSL and one power adapter interface. The Router should not be located where it will be exposed to moisture or excessive heat. Place the Router in a location where it can be safely connected to the various devices as well as to a power source. 2.
TD-8810 External ADSL2+ Router User Guide ¾ LAN: Connect with your computer’s NIC. ¾ LINE (WAN): Connect to the MODEM Port of Splitter or Connect with the telephone line. 2.3 Hardware installation procedures The procedure to install the Router can be described in general terms in the following steps: Step 1: Connecting the MODEM port of Splitter with the TD-8810 ADSL Router LINE port by telephone line. While you need to use a telephone, please attach telephone line into the phone of Splitter.
TD-8810 External ADSL2+ Router User Guide Chapter 3. System Configuration 3.1 Computer Configuration 1. Connect the cable according to Chapter 2, turn on the power. 2. Change the IP address of your PC（Figure 3-1）: Open TCP/IP Properties of the LAN card in your PC, enter the IP address as 192.168.1.*. ) Note: (* is any value between 2 to 254, Net mask is 255.255.255.0, Gateway is 192.168.1.1, DNS address is the value provided by ISP).
TD-8810 External ADSL2+ Router User Guide ) Note: The words in fact may be different with this guide. Remarks: you can check whether your configuration is successful through PING command. Enter Ping 192.168.1.1 If the screen looks like the following, you have been successful. Figure 3-2 If the screen looks like the following, the connection has failed. Please try again. Figure 3-3 3.2 Login Startup Internet Explorer, and enter 192.168.1.
TD-8810 External ADSL2+ Router User Guide Figure 3-4 3.3 1) Quick Setup Figure 4 is the main page of the Router. Figure 3-5 2) Please select Quick Setup. Enter the VPI and VCI values provided by your Internet Service Provider and click Next.
TD-8810 External ADSL2+ Router User Guide Figure 3-6 3) Select the relevant Connection Type and Encapsulation mode as the settings provided by your Internet Service Provider and click Next. 3.3.1 PPPoA a) Select PPP over ATM (PPPoA) Connection Type, and click Next. Figure 3-7 b) Enter the Username and Password provided by your Internet Service Provider and click Next.
TD-8810 External ADSL2+ Router User Guide Figure 3-8 c) Turn on the selected functions according to your demands. Clicking the next button to enter the next step. Figure 3-9 d) Click Save/Reboot.
TD-8810 External ADSL2+ Router User Guide Figure 3-10 3.3.2 PPPoE a) Select PPP over Ethernet (PPPoE) Connection Type, and click Next. Figure 3-11 b) Enter the Username and Password provided by your Internet Service Provider and click Next.
TD-8810 Figure 3-12 c) Click Save/Reboot.
TD-8810 External ADSL2+ Router User Guide Note： The Router will restart when you complete the configuration, so you have to wait for a while until it restarts successfully. 3.3.3 MER a) Select MAC Encapsulation Routing (MER) Connection Type, and click Next. b) Enter the parameter and the way which is provided by your ISP, then click Next.
TD-8810 External ADSL2+ Router User Guide Figure 3-14 c) Turn on the selected functions according to your needs. Click Next. Figure 3-15 d) Click Save/Reboot.
TD-8810 External ADSL2+ Router User Guide Figure 3-16 3.3.4 IPoA a) Select IP over ATM (IPoA) Connection Type, and click Next.
TD-8810 b) External ADSL2+ Router User Guide Enter the parameter and the way which is provided by your ISP, then click Next. Figure 3-18 c) Turn on the selected functions according to your needs. Click Next Figure 3-19 d) Click Save/Reboot.
TD-8810 Figure 3-20 3.3.5 Bridging a) Select Bridging Connection Type, and click Next. Figure 3-21 b) Click Save/Reboot.
TD-8810 External ADSL2+ Router User Guide Figure 3-22 ) Note: After you complete any setup, the new setup must be saved and the Router must be restarted for the configuration to go into effect. Please click the Save/Reboot button to restart. 3.
TD-8810 External ADSL2+ Router User Guide Figure 3-24 3.5 Web Setup Choose “Advanced Setup”Æ”WAN”, you will enter the page of Wide Area Network (WAN) Setup, you will see the Figure 3-25.
TD-8810 External ADSL2+ Router User Guide Figure 3-26 Enter VPI/VCI value and service category which is provided by your ISP, click next to enter the next step. You will see the Figure 3-27. ) Note: The type of network protocol selected may be different in different areas, there are five types （Figure 3-27）, So you should ask your ISP to acquire the local type of network protocol and Encapsulation mode. Figure 3-27 After choosing the proper protocol, enter the correct parameters supported by your ISP.
TD-8810 External ADSL2+ Router User Guide the configurations, and then you will go to Internet. ¾ PPP over ATM (PPPoA) If you select the protocol of PPP over ATM (PPPoA), you will see the Figure 3-28, in which please enter the value of user name and password which is provided by your ISP. After selecting the other function (it’s recommended to keep the default setup), click Next to continue. Figure 3-28 You will see the Figure 3-29, and then turn on the selected functions according to your demands.
TD-8810 External ADSL2+ Router User Guide Figure 3-29 Figure 3-30 ¾ PPP over Ethernet (PPPoE) If you select the protocol of PPP over Ethernet (PPPoE), you will see the Figure 3-31, in which please enter the value of user name and password which is provided by your ISP. After selecting the other function (it’s recommended to keep the default setup), click the next button.
TD-8810 External ADSL2+ Router User Guide Figure 3-31 You will see the Figure 3-32, and then turn on the selected functions according to your needs. Clicking the next button to enter the next step, you will see the Figure 3-33, finally click save to complete the configuration.
TD-8810 External ADSL2+ Router User Guide Figure 3-33 ¾ MAC Encapsulation Routing (MER) If you select the protocol of MAC Encapsulation Routing (MER), you will see the page (Figure 3-34), Enter the parameter and the way which is provided by your ISP, then click the next button. Figure 3-34 You will see the Figure 3-35, and then turn on the selected functions according to your needs.
TD-8810 External ADSL2+ Router User Guide Figure 3-35 Figure 3-36 ¾ IP over ATM (IPoA) If you select the protocol of IP over ATM (IPoA), you will see the Figure 3-37, enter the parameter and the way which is provided by your ISP, then click the next button.
TD-8810 External ADSL2+ Router User Guide Figure 3-37 You will see the page (Figure 3-38), then turn on the selected functions according to your needs. Clicking the next button to enter the next step, you will see the Figure 3-39, finally click save to complete the configuration.
TD-8810 External ADSL2+ Router User Guide Figure 3-39 ¾ Bridging If you select the Bridging protocol, you just open the bridge service function options, you will see the Figure 3-40, then click the next button, you will see the Figure 3-41, finally click save to complete the configuration.
TD-8810 External ADSL2+ Router User Guide Figure 3-41 ) Note: After you complete any setup, the new setup must be saved and the Router must be restarted for the configuration to go into effect. Please click the Save/Reboot button to restart, referring to the Figure 3-42. Figure 3-42 ) Note: All of the above setup is under windows XP OS. 3.5.
TD-8810 External ADSL2+ Router User Guide To setup an Address Reservation entry: ) Note: 1. DHCP IP Reservation are not available for the connection type of Bridge here, they won’t display on the screen below since only Bridge is selected. 2. DHCP IP Reservation are not available for the connection type of PPPoE with PPP IP Extension function selected, and they won’t display on the screen below since PPP IP Extension is selected.
TD-8810 External ADSL2+ Router User Guide Figure 3-26 2. Click New Entry button to add new entries, and the screen showed below pop up, you can modify an address reservation entry in this screen; Figure 3-27 3. Type the MAC Address (00:13:8F:A9:E6: CA for instance) of the computer which you want to reserve an IP (192.168.1.100 for instance) for in the MAC Address text box; 4. Type the IP Address (192.168.1.100 for instance) you have reserved in the Reserved IP Address text box; 5.
TD-8810 External ADSL2+ Router User Guide Figure 3-28 7. Click Save/Reboot button to save the settings and reboot the router. ) Note: The function won't take effect until the router reboots. 3.5.2 DNS When you select the connection type PPPoE, PPPoA, MER or IPoA for WAN configuration, you will see the DNS menu in the Web-based Utility (shown in Figure 3-29). It includes DNS Server and Dynamic DNS submenus. Figure 3-29 3.5.2.1. DNS Server Choose “Advanced Setup”→“DNS”→“DNS Server”.
TD-8810 External ADSL2+ Router User Guide Figure 3-30 If you select Enable Automatic Assigned DNS, this Router will accept automatically the first received DNS assignment from one of PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection established process. If the checkbox is not selected, please enter the primary and/or optional secondary DNS server IP addresses provided by your ISP. Then click the Save button to save the new configuration.
TD-8810 External ADSL2+ Router User Guide Figure 3-31 To setup DDNS, follow these instructions: 1. Click the Add button (pop-up Figure 3-31), then you will set the DDNS in the next screen (shown in Figure 3-32). Figure 3-32 ) Note: This page allows you to add a Dynamic DNS address from DynDNS.org,TZO or No-IP. 2. Select D-DNS provider (DynDNS.org,TZO or No-IP) in the drop-down list.
TD-8810 External ADSL2+ Router User Guide 3. Enter the Hostname of the DNS Server, and select the corresponding Interface for the DDNS, you can leave it default. 4. Type the User Name and Password for your DDNS account. 5. Click the Save/Apply button to save the entry. 3.6 Software Dial If TD-8810 CPE work in bridged (RFC 1483 Bridged) mode when it connecting Internet. You must install dial software on your PC.
TD-8810 Chapter 4. External ADSL2+ Router User Guide Advantage management setup In order to satisfy our customer's needs we offer an excellent Web management interface. Feel free to utilize the Advantage application and online software upgrades. The functions of the Web management interface are as follows: ¾ Upgrade software ¾ Modify the default IP address of the port of LAN(192.168.1.
TD-8810 Appendix A: 1. External ADSL2+ Router User Guide FAQ What related parameters are required to acquire ISP when you want to access the internet by ADSL Router? 1) Dial user: Connection protocol, User name, Password, Value of VPI/VCI, Encapsulation mode of AAL5 and so on. 2) Static IP user: Connection protocol, WAN IP Address, Subnet Mask, Gateway, Value of VPI/VCI, Encapsulation mode of AAL5 and so on. 2.
TD-8810 3) External ADSL2+ Router User Guide This product has the PPP dial procedure inside, so you will not need to use the dial software if your protocol is PPPoA or PPPoE, ADSL Modem will connect automatically. 4) You can check whether your ADSL Modem succeeds in connection with PING command.
TD-8810 Appendix B: External ADSL2+ Router User Guide Default Config User name admin Password admin IP Address 192.168.1.
