TL-WR702N 150Mbps Wireless N Nano Router Rev: 1.1.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD.
FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations.
Korea Warning Statements: 당해 무선설비는 운용중 전파혼신 가능성이 있음.
This product can be used in the following countries: AT BG BY CA CZ DE DK EE ES FI FR GB GR HU IE IT LT LV MT NL NO PL PT RO RU SE SK TR UA
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 150Mbps Wireless N Nano Router Model No.
CONTENTS Package Contents..................................................................................................................................1 Chapter 1. Introduction.......................................................................................................................2 1.1 Overview of the Router .......................................................................................................2 1.2 Conventions ............................................................
4.7 4.8 4.6.2 Wireless Security................................................................................................. 35 4.6.3 MAC Filtering ....................................................................................................... 37 4.6.4 Wireless Advanced .............................................................................................. 39 4.6.5 Wireless Statistics................................................................................................
5.8 5.9 5.7.1 DHCP Settings..................................................................................................... 75 5.7.2 DHCP Clients List ................................................................................................ 77 5.7.3 Address Reservation ........................................................................................... 77 Forwarding ....................................................................................................................
5.14.6 Reboot ............................................................................................................... 107 5.14.7 Password ........................................................................................................... 108 5.14.8 System Log........................................................................................................ 108 5.14.9 Statistics.............................................................................................................
7.7 7.8 7.6.1 Wireless Settings............................................................................................... 131 7.6.2 Wireless Security............................................................................................... 133 DHCP ............................................................................................................................. 136 7.7.1 DHCP Settings.................................................................................................
8.8.5 Reboot ............................................................................................................... 160 8.8.6 Password ........................................................................................................... 161 8.8.7 System Log........................................................................................................ 162 Appendix A: FAQ .............................................................................................................
TL-WR702N 150Mbps Wireless N Nano Router Package Contents The following items should be found in your package: ¾ One TL-WR702N 150Mbps Wireless N Nano Router ¾ Quick Installation Guide ¾ One Power Adapter ¾ One USB Cable ¾ One RJ-45 Ethernet Cable ¾ One Resource CD for TL-WR702N 150Mbps Wireless N Nano Router, including: • User Guide • Other Helpful Information ) Note: Make sure that the package contains the above items.
TL-WR702N 150Mbps Wireless N Nano Router Chapter 1. Introduction 1.1 Overview of the Router Small enough to fit in the average pocket, the TL-WR702N 150Mbps Wireless N Nano Router is uniquely suited to provide robust wireless networking to travelers, students, or anyone else for work or play. Incredible Speed TL-WR702N supports the newest 802.11n standards, and provides backward compatibility with older 802.11b/g standards as well.
TL-WR702N 150Mbps Wireless N Nano Router 1.2 Conventions The Router or TL-WR702N mentioned in this guide stands for TL-WR702N 150Mbps Wireless N Nano Router without any explanation. Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation. You can set the parameters according to your demand. 1.3 Main Features ¾ Complies with IEEE 802.
TL-WR702N ¾ 150Mbps Wireless N Nano Router LAN/WAN: This LAN/WAN port works as LAN in AP/Repeater/ Bridge/Client mode and as WAN in Router mode. As LAN, it connects the Router to the local PC; as WAN, it enables you connect the DSL/cable Modem, or Ethernet. ¾ Power: This port is used to connect the provided power adapter. ¾ Reset：It is used to reset the Router to its factory defaults.
TL-WR702N 150Mbps Wireless N Nano Router Chapter 2. Connecting the Router 2.1 System Requirements ¾ Each PC in the LAN needs a working Ethernet Adapter ¾ TCP/IP protocol must be installed on each PC ¾ Web browser, such as Microsoft Internet Explorer 5.
TL-WR702N 2.3.1 150Mbps Wireless N Nano Router AP Mode As the supplement of wired LAN, TL-WR702N enables the wired LAN to connect to the Internet wirelessly. The default mode of TL-WR702N is AP. Plug the power plug of TL-WR702N in electrical wall socket and connect the Ethernet cable correctly, you can surf the Internet by connecting your PC(s) to the Router wirelessly. On this mode, the only wired port works as LAN. Computer could connect to the device by either wired or wireless way.
TL-WR702N 150Mbps Wireless N Nano Router Figure 2-2 Hardware Installation of the TL-WR702N in Router Mode 1. Connect the WAN port of TL-WR702N to the LAN Port on the DSL/Cable Modem. 2. Connect the WAN port on the DSL/Cable Modem to the wired Internet. 3. Plug the power plug of TL-WR702N in electrical wall socket. 4. Power on the DSL/Cable Modem, PC(s) and notebook(s). 2.3.3 Repeater Mode TL-WR702N is used to extend the range of wireless signal of the existing AP or wireless router.
TL-WR702N 150Mbps Wireless N Nano Router ) Note: It is recommended that you connect a PC/notebook to the LAN port of the Router with an Ethernet cable, and then login the Router from the PC/notebook to set the Router in AP Repeater mode. 2.3.4 Bridge Mode Similar to the Bridge mode, TL-WR702N in Bridge mode is also used to extend the range of wireless signal of the existing AP or wireless router. On this mode, the only wired port works as LAN.
TL-WR702N 150Mbps Wireless N Nano Router Figure 2-5 Hardware Installation of the TL-WR702N in Client Mode 1. Connect the PC to the LAN/WAN port of TL-WR702N router with an Ethernet cable. 2. Plug the power plug of TL-WR702N in electrical wall socket. 3. Power on the PC(s). ) Note: TL-WR702N can be powered by external power adapter or USB connection to computer.
TL-WR702N 150Mbps Wireless N Nano Router Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your TL-WR702N 150Mbps Wireless N Nano Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default IP address of the TL-WR702N 150Mbps Wireless N Nano Router is 192.168.0.254. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for description.
TL-WR702N 150Mbps Wireless N Nano Router Figure 3-2 Failure result of Ping command Please check the connection following these steps: 1. Is the connection between your PC and the Router correct? ) Note: The LED of LAN/WAN ports which you link to on the Router should be lit. 2. Is the TCP/IP configuration for your PC correct? ) Note: If the Router's IP address is 192.168.0.254, your PC's IP address must be within the range of 192.168.0.1 ~ 192.168.0.253. 3.
TL-WR702N 150Mbps Wireless N Nano Router Figure 3-3 Login Windows ) Note: If the above screen does not pop-up, it means that your Web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it. 2. After a successfully login, you can click the Quick Setup menu to quickly configure your Router. Figure 3-4 Quick Setup 3.
TL-WR702N 150Mbps Wireless N Nano Router Figure 3-5 Quick Setup - Working Mode ) Note: The Router supports five working modes for multi-user to access the Internet: AP, Router, Repeater, Bridge and Client. In AP mode, TL-WR702N enables the wired LAN to connect to the Internet wirelessly. In Router mode, it can access the Internet via DSL/Cable Modem. In Repeater mode, the device will relay data to an associated root AP. In Bridge mode, the device bridges to another AP.
TL-WR702N 150Mbps Wireless N Nano Router Figure 3-6 Quick Setup - Wireless AP ¾ Wireless Radio - Enable or disable the wireless radio choosing from the pull-down list. ¾ SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address).
TL-WR702N 150Mbps Wireless N Nano Router • 11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients. • 11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. Select the desired wireless mode. When 802.11g mode is selected, only 802.11g wireless stations can connect to the Router. When 802.11n mode is selected, only 802.11n wireless stations can connect to the AP. It is strongly recommended that you set the Mode to 802.11b/g/n, and all of 802.11b, 802.
TL-WR702N 150Mbps Wireless N Nano Router Figure 3-8 Quick Setup – Finish 3.2.2 Router Mode When you choose Router on Working Mode page in Figure 3-5 , take the following steps: 1. Click Next in Figure 3-5, and you will see the following screen. The wireless settings on Router mode are the same as that on AP mode. Figure 3-9 Quick Setup - Wireless Router 2. Click Next in Figure 3-9, and then WAN Connection Type page will appear as shown in Figure 3-10.
TL-WR702N 150Mbps Wireless N Nano Router Figure 3-10 Quick Setup - WAN Connection Type The Router supports three popular ways PPPoE, Dynamic IP and Static IP to connect to the Internet. To make sure the connection type your ISP provides, please refer to the ISP. Make sure the cable is securely plugged into the WAN port before detection. ¾ PPPoE - For this connection, you will need your account name and password from your ISP.
TL-WR702N 150Mbps Wireless N Nano Router Figure 3-12 Quick Setup – MAC Clone ¾ Static IP - This type of connection uses a permanent, fixed (static) IP address that your ISP assigned. In this type, you should fill in the IP address, Subnet Mask, Default Gateway, and DNS IP address manually, which are specified by your ISP. Then click Next and proceed to Figure 3-14. Figure 3-13 Quick Setup - Static IP 3. Click Next, you will see the Finish page as shown in Figure 3-14.
TL-WR702N 3.2.3 150Mbps Wireless N Nano Router Repeater Mode When you choose Repeater Mode on Working Mode page in Figure 3-5 , take the following steps: 1. Click Next, and then Wireless Repeater page will appear as shown in Figure 3-15. Figure 3-15 Quick Setup - Wireless Repeater ¾ SSID - The SSID of AP that you want to access. ¾ MAC of AP - The MAC address of AP that you want to access. ¾ Region - Select your region from the pull-down list.
TL-WR702N 150Mbps Wireless N Nano Router Click Survey button on the Wireless page as shown in Figure 3-15, and then AP List page will appear as shown in Figure 3-16. Find the SSID of the Access Point you want to access, and click Connect in the corresponding row. For example, the third item is selected. The target network’s SSID will be automatically filled into the corresponding box which is shown as the Figure 3-15.
TL-WR702N 150Mbps Wireless N Nano Router Figure 3-17 Quick Setup - Finish 3.2.4 Bridge Mode When you choose Bridge on Working Mode page in Figure 3-5 , take the following steps: 1. Click Next, and then Wireless Repeater page will appear as shown in Figure 3-18. Figure 3-18 Quick Setup - Wireless Bridge ¾ SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network.
TL-WR702N ¾ 150Mbps Wireless N Nano Router Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. ¾ Channel - This field determines which operating frequency will be used.
TL-WR702N ¾ 150Mbps Wireless N Nano Router PassWord - If the AP your Router is going to connect needs password, you need to fill the password in this blank. Click Survey button on the Wireless page as shown in Figure 3-18, and then AP List page will appear as shown in Figure 3-19. Find the SSID of the Access Point you want to access, and click Connect in the corresponding row. For example, the third item is selected.
TL-WR702N 150Mbps Wireless N Nano Router Figure 3-20 Quick Setup - Wireless Security Settings This page is for setting wireless security of your own AP. When computers and mobile phones are connected to the AP, they should input the same password. ¾ Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. It is recommended strongly to enable security.
TL-WR702N 150Mbps Wireless N Nano Router Figure 3-22 Quick Setup - Wireless Client ¾ SSID - Enter the SSID that you want to access. ¾ MAC of AP - Enter the MAC address of AP that you want to access. ¾ Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field.
TL-WR702N 150Mbps Wireless N Nano Router Figure 3-23 AP List 3. Click the Next button in Figure 3-24. You will then see the Finish page. Click the Reboot button to make your wireless configuration take effect and finish the Quick Setup.
TL-WR702N 150Mbps Wireless N Nano Router ) Note: 1. The operating distance or range of your wireless connection varies significantly based on the physical placement of the Router. For best results, place your Router. z Near the center of the area in which your wireless stations will operate. z In an elevated location such as a high shelf. z Away from the potential sources of interference, such as PCs, microwaves, and cordless phones. z Away from large metal surfaces.
TL-WR702N 150Mbps Wireless N Nano Router Chapter 4. Configuration for AP Mode This chapter will show each Web page's key functions and the configuration way for AP Mode of TL-WR702N. 4.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions.
TL-WR702N 150Mbps Wireless N Nano Router Figure 4-2 Status ¾ Firmware Version - The version information of the Router’s firmware. ¾ Hardware Version - The version information of the Router’s hardware. ¾ LAN - This field displays the current settings or information for the LAN, you can configure them in the Network > LAN page. • MAC address - The physical address of the Router, as seen from the LAN. • IP address - The LAN IP address of the Router.
TL-WR702N 150Mbps Wireless N Nano Router • Channel Width - The current wireless channel width in use. • MAC address - The physical address of the Router, as seen from the WLAN. • WDS Status - The status of WDS connection. ¾ System Up Time - The length of the time since the Router was last powered on or reset. Click the Refresh button to get the latest status and settings of the Router. 4.3 Quick Setup Please refer to Section 3.2: "Quick Installation Guide." 4.
TL-WR702N 150Mbps Wireless N Nano Router 4.5 Network Figure 4-5 the Network menu There is only one submenu under the Network menu (shown in Figure 4-5): LAN. 4.5.1 LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 4-6 LAN ¾ Address Type - Choosing Smart IP(DHCP) to get IP address from DHCP server, or choosing Static IP to configure IP address manually. ¾ MAC Address - The physical address of the LAN ports, as seen from the LAN.
TL-WR702N 150Mbps Wireless N Nano Router 4.6 Wireless Figure 4-7 Wireless menu There are five submenus under the Wireless menu (shown in Figure 4-7): Wireless Settings, Wireless Security, MAC Filtering, Wireless Advanced and Wireless Statistics. Click any of them, and you will be able to configure the corresponding function. 4.6.1 Wireless Settings Choose menu “Wireless → Wireless Settings”, and then you can configure the basic settings for the wireless network on this page.
TL-WR702N 150Mbps Wireless N Nano Router name (SSID) to a different value. This value is case-sensitive. For example, TEST is NOT the same as test. ¾ Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field.
TL-WR702N ¾ 150Mbps Wireless N Nano Router SSID (to be bridged) - The SSID of the AP your Router is going to connect to as a client. You can also use the search function to select the SSID to join. ¾ BSSID (to be bridged) - The BSSID of the AP your Router is going to connect to as a client. You can also use the search function to select the BSSID to join. ¾ Survey - Click this button, you can survey the AP which runs in the current channel.
TL-WR702N z 150Mbps Wireless N Nano Router Away from large metal surfaces. 2. Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the Router. 4.6.2 Wireless Security Choose menu “Wireless → Wireless Security”, and then you can configure the security settings of your wireless network. There are three wireless security modes supported by the Router: WEP (Wired Equivalent Privacy), WPA/WPA2 and WPA-PSK/WPA2-PSK.
TL-WR702N ¾ 150Mbps Wireless N Nano Router WEP - It is based on the IEEE 802.11 standard. • Type - you can choose the type for the WEP security on the pull-down list. The default setting is Automatic, which can select Shared Key or Open System authentication type automatically based on the wireless station's capability and request. • WEP Key Format - Hexadecimal and ASCII formats are provided here.
TL-WR702N 150Mbps Wireless N Nano Router • Version - you can choose the version of the WPA-PSK security on the drop-down list. The default setting is Automatic (Recommended), which can select WPA-PSK (Pre-shared key of WPA) or WPA2-PSK (Pre-shared key of WPA) automatically based on the wireless station's capability and request. • Encryption - When WPA-PSK or WPA is set as the Authentication Type, you can select Automatic (Recommended), TKIP or AES as Encryption.
TL-WR702N 150Mbps Wireless N Nano Router ¾ MAC Address - The wireless station's MAC address that you want to access. ¾ Status - The status of this entry, either Enabled or Disabled. ¾ Description - A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New… button.
TL-WR702N 150Mbps Wireless N Nano Router For example: If you desire that the wireless station A with MAC address 00-0A-EB-B0-00-0B and the wireless station B with MAC address 00-0A-EB-00-07-5F are able to access the Router, but all the other wireless stations cannot access the Router, you can configure the Wireless MAC Address Filtering list by following these steps: 1. Click the Enable button to enable this function. 2.
TL-WR702N 150Mbps Wireless N Nano Router Figure 4-12 Wireless Advanced ¾ Transmit Power - Here you can specify the transmit power of Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. ¾ Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here. The beacons are the packets sent by the Router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons.
TL-WR702N ¾ 150Mbps Wireless N Nano Router Enabled AP Isolation - This function isolate all connected wireless stations so that wireless stations cannot access each other through WLAN. This function will be disabled if WDS/Bridge is enabled. ) Note: If you are not familiar with the setting items in this page, it's strongly recommended to keep the provided default values; otherwise it may result in lower wireless network performance. 4.6.
TL-WR702N 150Mbps Wireless N Nano Router 4.7 DHCP Figure 4-14 The DHCP menu There are three submenus under the DHCP menu (shown in Figure 4-14), DHCP Settings, DHCP Clients List and Address Reservation. Click any of them, and you will be able to configure the corresponding function. 4.7.
TL-WR702N 150Mbps Wireless N Nano Router Figure 4-16 DHCP Settings ¾ DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually. ¾ Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address. ¾ End IP Address - Specify an IP address for the DHCP Server to end with when assigning IP addresses. 192.
TL-WR702N 4.7.2 150Mbps Wireless N Nano Router DHCP Clients List Choose menu “DHCP → DHCP Clients List”, and then you can view the information about the clients attached to the Router in the screen as shown in Figure 4-17. Figure 4-17 DHCP Clients List ¾ Client Name - The name of the DHCP client ¾ MAC Address - The MAC address of the DHCP client ¾ Assigned IP - The IP address that the Router has allocated to the DHCP client ¾ Lease Time - The time of the DHCP client leased.
TL-WR702N 150Mbps Wireless N Nano Router ¾ Reserved IP Address - The IP address reserved for the PC by the Router. ¾ Status - The status of this entry either Enabled or Disabled. To Reserve an IP address: 1. Click the Add New… button. Then Figure 4-19 will pop-up. 2. Enter the MAC address (in XX-XX-XX-XX-XX-XX format.) and IP address (in dotted-decimal notation) of the computer for which you want to reserve an IP address. 3. Click the Save button.
TL-WR702N 150Mbps Wireless N Nano Router Choose menu “System Tools”, and then you can see the submenus under the main menu: Diagnostic, Firmware, Factory Defaults, Backup & Restore, Reboot, Password, and System Log. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.8.
TL-WR702N ¾ 150Mbps Wireless N Nano Router IP Address/Domain Name - Type the destination IP address (e.g. 202.108.22.5) or Domain name (e.g. http://www.tp-link.com). ¾ Pings Count - The number of Ping packets for a Ping connection. The default is 4. ¾ Ping Packet Size - The size of Ping packet. The default is 64. ¾ Ping Timeout - Set the waiting time for the reply of each Ping packet. If there is no reply in the specified time, the connection is overtime. The default is 800.
TL-WR702N ¾ 150Mbps Wireless N Nano Router Hardware Version - This displays the current hardware version. The hardware version of the upgrade file must accord with the Router’s current hardware version. To upgrade the Router's firmware, follow these instructions below: 1. Download a more recent firmware upgrade file from the TP-LINK website (http://www.tp-link.com). 2. Type the path and file name of the update file into the File field, or click the Browse button to locate the update file. 3.
TL-WR702N 150Mbps Wireless N Nano Router ) Note: All changed settings will be lost when defaults are restored. 4.8.4 Backup & Restore Choose menu “System Tools → Backup & Restore”, and then you can save the current configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 4-25. Figure 4-25 Backup & Restore Configuration ¾ Click the Backup button to save all configuration settings as a backup file in your local computer.
TL-WR702N 150Mbps Wireless N Nano Router • Change the LAN IP Address (system will reboot automatically). • Change the DHCP Settings. • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically). • Restore the Router's settings to factory defaults (system will reboot automatically). • Update the configuration with the file (system will reboot automatically). 4.8.
TL-WR702N 4.8.7 150Mbps Wireless N Nano Router System Log Choose menu “System Tools → System Log”, and then you can view the logs of the Router. Figure 4-28 System Log ¾ Refresh - Refresh the page to show the latest log list. ¾ Clear All - All the logs will be deleted from the Router permanently, not just from the page.
TL-WR702N 150Mbps Wireless N Nano Router Chapter 5. Configuration for Router Mode This chapter will show each Web page's key functions and the configuration way for Router Mode of TL-WR702N. 5.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-2 ¾ Firmware Version - The version information of the Router’s firmware. ¾ Hardware Version - The version information of the Router’s hardware.
TL-WR702N ¾ 150Mbps Wireless N Nano Router LAN - This field displays the current settings or information for the LAN, you can configure them in the Network > LAN page. • MAC Address - The physical address of the Router, as seen from the LAN. • IP Address - The LAN IP address of the Router. • Subnet Mask - The subnet mask associated with LAN IP address. ¾ Wireless - This field displays basic information or status for wireless function, you can configure them in the Wireless > Wireless Settings page.
TL-WR702N 150Mbps Wireless N Nano Router • Received (Packets) - Traffic that counted in packets has been received out from the WAN port. ¾ System Up Time - The length of the time since the Router was last powered on or reset. Click the Refresh button to get the latest status and settings of the Router. 5.3 Quick Setup Please refer to Section 3.2: "Quick Installation Guide." 5.4 Working Mode The Router supports five operation mode types: AP, Router, Repeater, Bridge and Client.
TL-WR702N 150Mbps Wireless N Nano Router 5.5 Network Figure 5-5 the Network menu There are three submenus under the Network menu (shown in Figure 5-5): WAN, LAN and MAC Clone. Click any of them, and you will be able to configure the corresponding function. 5.5.1 WAN Choose menu “Network → WAN”, and then you can configure the IP parameters of the WAN on the screen below. 1.
TL-WR702N 150Mbps Wireless N Nano Router This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters. ¾ MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP.
TL-WR702N 150Mbps Wireless N Nano Router ¾ IP Address - Enter the IP address in dotted-decimal notation provided by your ISP. ¾ Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0. ¾ Default Gateway - (Optional) Enter the gateway IP address in dotted-decimal notation provided by your ISP. ¾ MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes.
TL-WR702N ¾ 150Mbps Wireless N Nano Router Secondary Connection - It’s available only for PPPoE Connection. If your ISP provides an extra Connection type such as Dynamic/Static IP to connect to a local area network, then you can check the radio button of Dynamic/Static IP to activate this secondary connection. • Disabled - The Secondary Connection is disabled by default, so there is PPPoE connection only. This is recommended.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-9 PPPoE Advanced Settings ¾ MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. ¾ Service Name/AC Name - The service name and AC (Access Concentrator) name should not be configured unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-10 WAN – L2TP/Russia L2TP ¾ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾ Dynamic IP/ Static IP - Choose either as you are given by your ISP. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately.
TL-WR702N ¾ 150Mbps Wireless N Nano Router Connect Manually - You can configure the Router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the Router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. To use this option, check the radio button.
TL-WR702N ¾ 150Mbps Wireless N Nano Router User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾ Dynamic IP/ Static IP - Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name. If you choose static IP and enter the domain name, you should also enter the DNS assigned by your ISP. And click the Save button. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately.
TL-WR702N 5.5.2 150Mbps Wireless N Nano Router LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 5-12 LAN ¾ MAC Address - The physical address of the LAN ports, as seen from the LAN. The value can't be changed. ¾ IP Address - Enter the IP address of your Router in dotted-decimal notation (factory default: 192.168.0.254). ¾ Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.
TL-WR702N 150Mbps Wireless N Nano Router Some ISPs require that you register the MAC Address of your adapter. Changes are rarely needed here. ¾ WAN MAC Address - This field displays the current MAC address of the WAN port. If your ISP requires you to register the MAC address, please enter the correct MAC address into this field in XX-XX-XX-XX-XX-XX format (X is any hexadecimal digit). ¾ Your PC's MAC Address - This field displays the MAC address of the PC that is managing the Router.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-15 Wireless Settings - Router ¾ SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address). But it is recommended strongly that you change your networks name (SSID) to a different value. This value is case-sensitive.
TL-WR702N 150Mbps Wireless N Nano Router Select the desired wireless mode. When 802.11g mode is selected, only 802.11g wireless stations can connect to the Router. When 802.11n mode is selected, only 802.11n wireless stations can connect to the AP. It is strongly recommended that you set the Mode to 802.11b/g/n, and all of 802.11b, 802.11g, and 802.11n wireless stations can connect to the Router. ¾ Channel Width - Select any channel width from the pull-down list.
TL-WR702N ¾ 150Mbps Wireless N Nano Router WEP Index - This option should be chosen if the key type is WEP (ASCII) or WEP (HEX). It indicates the index of the WEP key. ¾ Authentication Type - This option should be chosen if the key type is WEP (ASCII) or WEP (HEX). It indicates the authorization type of the Root AP. ¾ Password - If the AP your Router is going to connect needs password, you need to fill the password in this blank. Be sure to click the Save button to save your settings on this page.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-16 Wireless Security ¾ Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. But it’s strongly recommended to choose one of the following modes to enable security. ¾ WEP - It is based on the IEEE 802.11 standard. • Type - you can choose the type for the WEP security on the pull-down list.
TL-WR702N 150Mbps Wireless N Nano Router • WEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identical on all wireless stations in your network. • Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption. "Disabled" means this WEP key entry is invalid. 64-bit - You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 ASCII characters.
TL-WR702N 150Mbps Wireless N Nano Router For ASCII, the key can be made up of any numbers 0 to 9 and any letters A to Z, the length should be between 8 and 63 characters. For Hexadecimal, the key can be made up of any numbers 0 to 9 and letters A to F, the length should be between 8 and 64 characters. Please also note the key is case sensitive, this means that upper and lower case keys will affect the outcome. It would also be a good idea to write down the key and all related wireless security settings.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-18 Add or Modify Wireless MAC Address Filtering entry To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0A-EB-B0-00-0B. 2. Give a simple description for the wireless station in the Description field. For example: Wireless station A. 3.
TL-WR702N 150Mbps Wireless N Nano Router 3. Delete all or disable all entries if there are any entries already. 4. Click the Add New... button. 1) Enter the MAC address 00-0A-EB-B0-00-0B/00-0A-EB-00-07-5F in the MAC Address field. 2) Enter wireless station A/B in the Description field. 3) Select Enabled in the Status pull-down list. 4) Click the Save button. 5) Click the Back button. The filtering rules that configured should be similar to the following list: 5.6.
TL-WR702N ¾ 150Mbps Wireless N Nano Router Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here. The beacons are the packets sent by the Router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100. ¾ RTS Threshold - Here you can specify the RTS (Request to Send) Threshold.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-20 Wireless Statistics ¾ MAC Address - The connected wireless station's MAC address ¾ Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN / Disconnected ¾ Received Packets - Packets received by the station ¾ Sent Packets - Packets sent by the station You cannot change any of the values on this page.
TL-WR702N 150Mbps Wireless N Nano Router Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router on the LAN. Figure 5-22 DHCP Settings ¾ DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually. ¾ Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.
TL-WR702N 150Mbps Wireless N Nano Router ) Note: To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". 5.7.2 DHCP Clients List Choose menu “DHCP → DHCP Clients List”, and then you can view the information about the clients attached to the Router in the screen as shown in Figure 5-23.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-24 Address Reservation ¾ MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾ Reserved IP Address - The IP address reserved for the PC by the Router. ¾ Status - The status of this entry, either Enabled or Disabled. To Reserve an IP address: 1. Click the Add New… button. Then will pop-up. 2. Enter the MAC address (in XX-XX-XX-XX-XX-XX format.
TL-WR702N 150Mbps Wireless N Nano Router 5.8 Forwarding Figure 5-26 The Forwarding menu There are four submenus under the Forwarding menu (shown in Figure 5-26): Virtual Servers, Port Triggering, DMZ and UPnP. Click any of them, and you will be able to configure the corresponding function. 5.8.1 Virtual Servers Choose menu “Forwarding → Virtual Servers”, and then you can view and add virtual servers in the screen as shown in Figure 5-27.
TL-WR702N 150Mbps Wireless N Nano Router To setup a virtual server entry: 1. Click the Add New… button, the next screen will pop-up as shown in Figure 5-28. 2. Select the service port you want to use from the Common Service Port list. If the Common Service Port list does not have the service that you want to use, type the service port number or service port range in the Service Port box. 3. Type the IP Address of the computer in the IP Address box. 4.
TL-WR702N 150Mbps Wireless N Nano Router ) Note: If you set the service port of the virtual server as 80, you must set the Web management port on “Security → Remote Management” page to be any other value except 80 such as 8080. Otherwise there will be a conflict to disable the virtual server. 5.8.2 Port Triggering Choose menu “Forwarding → Port Triggering”, and then you can view and add port triggering in the screen as shown in Figure 5-29.
TL-WR702N 150Mbps Wireless N Nano Router To add a new rule, follow the steps below: 1. Click the Add New… button, the next screen will pop-up as shown in Figure 5-30. 2. Select a common application from the Common Applications drop-down list, then the Trigger Port field and the Incoming Ports field will be automatically filled. If the Common Applications do not have the application you need, enter the Trigger Port and the Incoming Ports manually. 3.
TL-WR702N 150Mbps Wireless N Nano Router ) Note: 1. When the trigger connection is released, the corresponding opening ports will be closed. 2. Each rule is allowed to be used only by one host on LAN synchronously. The trigger connection of other hosts on LAN will be refused. 3. Incoming Port Range cannot overlap each other. 5.8.3 DMZ Choose menu “Forwarding → DMZ”, and then you can view and configure DMZ host in the screen as shown in Figure 5-31.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-32 UPnP ¾ Current UPnP Status - UPnP can be enabled or disabled by clicking the Enable or Disable button. ¾ Current UPnP Settings List - This table displays the current UPnP information. • App Description - The description provided by the application in the UPnP request. • External Port - The external port the Router opens for the application. • Protocol - The type of protocol the Router opens for the application.
TL-WR702N 5.9.1 150Mbps Wireless N Nano Router Firewall Using the Firewall page, you can turn the general firewall switch on or off. The default setting for the switch is off. If the general firewall switch is off, even if IP Address Filtering, DNS Filtering and MAC Filtering are enabled, their settings are ineffective. Figure 5-34 Firewall Settings ¾ Enable Firewall - the general firewall switch is on or off. ¾ Enable IP Address Filtering - set IP Address Filtering is enabled or disabled.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-35 IP address Filtering To disable the IP Address Filtering feature, keep the default setting, Disabled. To set up an IP Address Filtering entry, click Enable Firewall and Enable IP Address Filtering on the Firewall page, and click the Add New… button.
TL-WR702N 150Mbps Wireless N Nano Router 6. Protocol - Select which protocol is to be used, either TCP, UDP, or All (all protocols supported by the router). 7. 8. 9. Action - Select either Allow or Deny through the router. Status - Select Enabled or Disabled for this entry on the Status pull-down list. Click the Save button to save this entry. To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-37 Domain Filtering Before adding a Domain Filtering entry, you must ensure that Enable Firewall and Enable Domain Filtering have been selected on the Firewall page. To Add a Domain filtering entry, click the Add New… button. The page "Add or Modify a Domain Filtering entry " will appear, shown in Figure 5-38: Figure 5-38 Add or Modify a Domain Filtering entry To add or modify a Domain Filtering entry, follow these instructions: 1.
TL-WR702N 150Mbps Wireless N Nano Router Click the Next button to go to the next page and the Previous button to return to the previous page. For example: if you want to block the PC(s) on your LAN to access websites www.xxyy.com.cn, www.aabbcc.com and websites with .net in the end on the Internet while no limit for other websites, you should specify the following Domain filtering list: 5.9.
TL-WR702N 150Mbps Wireless N Nano Router To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0E-AE-B0-00-0B. 2. 3. 4. Type the description of the PC in the Description field. Fox example: John’s PC. Status - Select Enabled or Disabled for this entry on the Status pull-down list. Click the Save button to save this entry.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-41 Remote Management ¾ Web Management Port - Web browser access normally uses the standard HTTP service port 80. This router’s default remote management Web port number is 80. For greater security, you can change the remote management Web interface to a custom port by entering that number in this box provided. Choose a number between 1024 and 65534, but do not use the number of any common service port.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-42 Advanced Security settings ¾ ¾ Packets Statistic interval (5 ~ 60) - The default value is 10. Select a value between 5 and 60 seconds in the pull-down list. The Packets Statistic interval value indicates the time section of the packets statistic. The result of the statistic used for analysis by SYN Flood, UDP Flood and ICMP-Flood. DoS protection - Enable or Disable the DoS protection function.
TL-WR702N 150Mbps Wireless N Nano Router ¾ Ignore Ping Packet from WAN Port - Enable or Disable ignore ping packet from WAN port. The default is disabled. If enabled, the ping packet from the Internet cannot access the router. ¾ Forbid Ping Packet from LAN Port - Enable or Disable forbidding Ping Packet to access the router from the LAN port. The default value is disabled. If enabled, the ping packet from the LAN port cannot access the router.
TL-WR702N 150Mbps Wireless N Nano Router To add static routing entries: 1. Click the Add New button. 2. Enter the following data: ¾ Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route. ¾ Subnet Mask - The Subnet Mask determines which portion of an IP Address is the network portion, and which portion is the host portion.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-46 IP QoS ¾ Enable IP QoS - Enable or disable the function of IP QoS. ¾ Choose BandWidth Type - Select the network connection type from the drop-down list. ¾ Bandwidth Apply - The bandwidth you get. If you are not clear about that, please contact with your ISP for help. ¾ IP Range - IP range of this entry. ¾ Mode - There are two types of mode: Minimum Bandwidth Guarantee and Maximum Bandwidth Limit.
TL-WR702N 150Mbps Wireless N Nano Router 4. IP address range for different entries could not have intersection with each other. 5. After the configurations, click the Save button for the change to take effect. 5.12 IP & MAC Binding Setting Figure 5-47 the IP & MAC Binding menu There are two submenus under the IP & MAC Binding menu: Binding Setting and ARP List. Click any of them, and you will be able to scan or configure the corresponding function.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-49 IP & MAC Binding Setting (Add & Modify) To add IP & MAC Binding entries: 1. Click the Add New… button. 2. Enter the MAC Address and IP Address. 3. Select the Bind checkbox. 4. Click the Save button to save it. To modify or delete an existing entry: 1. Find the desired entry in the table. 2. Click Modify or Delete as desired on the Modify column. To find an existing entry: 1. Click the Find button (shown in Figure 5-48). 2.
TL-WR702N 150Mbps Wireless N Nano Router 5.12.2 ARP List To manage the computer, you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list, and you could configure the items on the ARP list also. This page displays the ARP List; it shows all the existing IP & MAC Binding entries. Figure 5-51 ARP List ¾ MAC Address - The MAC address of the controlled computer in the LAN.
TL-WR702N 150Mbps Wireless N Nano Router service providers such as www.oray.net, www.comexe.cn, www.dyndns.org, or www.no-ip.com. The Dynamic DNS client service provider will give you a password or key. 5.13.1 No-IP DDNS If the dynamic DNS Service Provider you select is www.no-ip.com, the page will appear as shown in Figure 5-52. Figure 5-52 No-IP DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-53 PeanutHull DDNS Settings To set up for DDNS, follow these instructions: 1. Enter the User Name for your DDNS account. 2. Enter the Password for your DDNS account. 3. Click the Login button to login to the DDNS service. Connection Status - The status of the DDNS service connection is displayed here. Service Type - The type of service is displayed here. Domain Name - The domain names are displayed here.
TL-WR702N 150Mbps Wireless N Nano Router Figure 5-54 Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1. Type the Domain Name received from your dynamic DNS service provider. 2. Type the User Name for your DDNS account. 3. Type the Password for your DDNS account. 4. Click the Login button to log in to the DDNS service. Connection Status -The status of the DDNS service connection is displayed here. Click Logout to log out of the DDNS service.
TL-WR702N Figure 5-55 150Mbps Wireless N Nano Router Dyndns.org DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from dynamic DNS service provider here. 4. Click the Login button to log in to the DDNS service. Connection Status -The status of the DDNS service connection is displayed here. Click Logout to logout of the DDNS service.
TL-WR702N 150Mbps Wireless N Nano Router There are nine submenus under the System Tools menu: Time, Diagnostic, Firmware, Factory Defaults, Backup and Restore, Reboot, Password, System Log and Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 5.14.
TL-WR702N ¾ ¾ 150Mbps Wireless N Nano Router The time will be lost if the router is turned off. The router will obtain GMT automatically from Internet if it has already connected to Internet. 5.14.2 Diagnostic Choose menu “System Tools → Diagnostic”, you can transact Ping or Traceroute function to check connectivity of your network in the following screen. Figure 5-58 ¾ Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic too.
TL-WR702N ¾ 150Mbps Wireless N Nano Router IP Address/Domain Name - Type the destination IP address (such as 202.108.22.5) or Domain name (such as www.baidu.com). ¾ Pings Count - The number of Ping packets for a Ping connection. ¾ Ping Packet Size - The size of Ping packet. ¾ Ping Timeout - Set the waiting time for the reply of each Ping packet. If there is no reply in the specified time, the connection is overtime. ¾ Traceroute Max TTL - The max number of hops for a Traceroute connection.
TL-WR702N 150Mbps Wireless N Nano Router New firmware is posted at www.tp-link.com and can be downloaded for free. If the router is not experiencing difficulties, there is no need to upgrade firmware, unless the new firmware supports a new feature you need. ) Note: 1. When you upgrade the router's firmware, you will lose current configuration settings, so make sure you backup the router’s settings before you upgrade its firmware. 2.
TL-WR702N 150Mbps Wireless N Nano Router 5.14.5 Backup & Restore This page allows you to save current configuration of router as backup or restore the configuration file you saved before. Figure 5-62 Backup & Restore Configuration ¾ Click the Backup button to save all configuration settings as a backup file in your local computer. ¾ To restore the router's configuration, follow these instructions: • Click the Browse button to select the backup file which you want to restore.
TL-WR702N 150Mbps Wireless N Nano Router ¾ Web Service Port of the router ¾ Upgrade the firmware of the router (system will reboot automatically). ¾ Restore the router's settings to factory default (system will reboot automatically.) 5.14.7 Password This page allows you to change the factory default user name and password of the router. Figure 5-64 Password It is recommended strongly that you change the factory default user name and password of the router.
TL-WR702N 150Mbps Wireless N Nano Router The router can keep logs of all traffic. You can query the logs to find what happened to the router. Click the Refresh button to refresh the logs. Click the Clear All button to clear all the logs. 5.14.9 Statistics The Statistics page displays the network traffic of each PC in LAN, including total traffic and traffic of the last Packets Statistic interval seconds. Figure 5-66 Statistics ¾ Current Statistics Status - Enable or Disable.
TL-WR702N 150Mbps Wireless N Nano Router Statistics Table: IP Address Total Packets Bytes Current The IP Address displayed with statistics The total amount of packets received and transmitted by the router. The total amount of bytes received and transmitted by the router. Packets The total amount of packets received and transmitted in the last Packets Statistic interval seconds. Bytes The total amount of bytes received and transmitted in the last Packets Statistic interval seconds.
TL-WR702N 150Mbps Wireless N Nano Router Chapter 6. Configuration for Repeater Mode This chapter will show each Web page's key functions and the configuration way for Repeater Mode of TL-WR702N. 6.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions.
TL-WR702N 150Mbps Wireless N Nano Router Figure 6-2 Status ¾ Firmware Version - The version information of the Router’s firmware. ¾ Hardware Version - The version information of the Router’s hardware. ¾ LAN - This field displays the current settings or information for the LAN, you can configure them in the Network > LAN page. • MAC address - The physical address of the Router, as seen from the LAN. • IP address - The LAN IP address of the Router.
TL-WR702N 150Mbps Wireless N Nano Router 6.4 Working Mode The Router supports five operation mode types: AP, Router, Repeater, Bridge and Client. Please select one your want. Click Save to save your choice, which is shown as Figure 4-3. Figure 6-3 Working Mode ¾ AP - The wireless access point mode. ¾ Router - The wireless Router Mode. In this mode, the device enables multi-user to share Internet via DSL/Cable Modem. The only wired port works as WAN. ¾ Repeater - The wireless Repeater Mode.
TL-WR702N 6.5.1 150Mbps Wireless N Nano Router LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 6-6 LAN ¾ Address Type - Choosing Smart IP(DHCP) to get IP address from DHCP server, or choosing Static IP to configure IP address manually. ¾ MAC Address - The physical address of the LAN ports, as seen from the LAN. The value can't be changed.
TL-WR702N 6.6.1 150Mbps Wireless N Nano Router Wireless Settings Choose menu “Wireless → Wireless Settings”, and then you can configure the basic settings for the wireless network on this page. Figure 6-8 Wireless Settings - Repeater ¾ SSID - The SSID of AP that you want to access. ¾ MAC of AP - The MAC address of AP that you want to access. ¾ Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used.
TL-WR702N 150Mbps Wireless N Nano Router ¾ Authentication Type - This option should be chosen if the key type is WEP (ASCII) or WEP (HEX). It indicates the authentication type of the Root AP. ¾ Password - If the AP your router is going to connect need password, you need to fill the password in this blank. Be sure to click the Save button to save your settings on this page. ) Note: 1.
TL-WR702N 150Mbps Wireless N Nano Router Figure 6-10 DHCP Settings Figure 6-11 DHCP Settings ¾ DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually. ¾ Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address.
TL-WR702N 150Mbps Wireless N Nano Router time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. ¾ Default Gateway (Optional) - It is suggested to input the IP address of the LAN port of the Router. The default value is 192.168.0.254. ¾ Default Domain (Optional) - Input the domain name of your network. ¾ Primary DNS - (Optional) Input the DNS IP address provided by your ISP or consult your ISP.
TL-WR702N 150Mbps Wireless N Nano Router address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings. Figure 6-13 Address Reservation ¾ MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾ Reserved IP Address - The IP address reserved for the PC by the Router.
TL-WR702N 150Mbps Wireless N Nano Router Click the Enable/Disabled All button to make all entries enabled/disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page and Click the Previous button to return the previous page. 6.8 System Tools Figure 6-15 The System Tools menu Choose menu “System Tools”, and then you can see the submenus under the main menu: Diagnostic, Firmware, Factory Defaults, Backup & Restore, Reboot, Password, and System Log.
TL-WR702N Figure 6-16 ¾ 150Mbps Wireless N Nano Router Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. • Traceroute - This diagnostic tool tests the performance of a connection. ) Note: You can use ping/traceroute to test both numeric IP address or domain name.
TL-WR702N ¾ 150Mbps Wireless N Nano Router Traceroute Max TTL - The max number of hops for a Traceroute connection. The default is 20. Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 6-17 Diagnostic Results ) Note: Only one user can use this tool at one time.
TL-WR702N 2. 150Mbps Wireless N Nano Router Type the path and file name of the update file into the File field, or click the Browse button to locate the update file. 3. Click the Upgrade button. ) Note: 1. New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use.
TL-WR702N 6.8.4 150Mbps Wireless N Nano Router Backup & Restore Choose menu “System Tools → Backup & Restore”, and then you can save the current configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 6-20. Figure 6-20 Backup & Restore Configuration ¾ Click the Backup button to save all configuration settings as a backup file in your local computer. ¾ To upgrade the Router's configuration, follow these instructions.
TL-WR702N 150Mbps Wireless N Nano Router • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically). • Restore the Router's settings to factory defaults (system will reboot automatically). • Update the configuration with the file (system will reboot automatically. 6.8.
TL-WR702N 6.8.7 150Mbps Wireless N Nano Router System Log Choose menu “System Tools → System Log”, and then you can view the logs of the Router. Figure 6-23 System Log ¾ Refresh - Refresh the page to show the latest log list. ¾ Clear All - All the logs will be deleted from the Router permanently, not just from the page.
TL-WR702N 150Mbps Wireless N Nano Router Chapter 7. Configuration for Bridge Mode This chapter will show each Web page's key functions and the configuration way for Bridge Mode of TL-WR702N. 7.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions.
TL-WR702N 150Mbps Wireless N Nano Router Figure 7-2 Status ¾ Firmware Version - The version information of the Router’s firmware. ¾ Hardware Version - The version information of the Router’s hardware. ¾ LAN - This field displays the current settings or information for the LAN, you can configure them in the Network > LAN page. • MAC address - The physical address of the Router, as seen from the LAN. • IP address - The LAN IP address of the Router.
TL-WR702N 150Mbps Wireless N Nano Router • Channel Width - The current wireless channel width in use. • MAC address - The physical address of the Router, as seen from the WLAN. • WDS Status - The status of WDS connection. ¾ System Up Time - The length of the time since the Router was last powered on or reset. Click the Refresh button to get the latest status and settings of the Router. 7.3 Quick Setup Please refer to Section 3.2: "Quick Installation Guide." 7.
TL-WR702N 150Mbps Wireless N Nano Router Figure 7-4 7.5 Network Figure 7-5 the Network menu There is only one submenu under the Network menu (shown in Figure 7-5): LAN. 7.5.1 LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 7-6 LAN ¾ Address Type - Choosing Smart IP(DHCP) to get IP address from DHCP server, or choosing Static IP to configure IP address manually.
TL-WR702N 150Mbps Wireless N Nano Router server in this device will not start up. 3. If the new LAN IP address you set is not in the same subnet with the previous one, the IP Address pool in the DHCP server will be configured automatically, but the Virtual Server and DMZ Host will not take effect until they are re-configured. 7.6 Wireless Figure 7-7 Wireless menu There are two submenus under the Wireless menu (shown in Figure 7-7): Wireless Settings and Wireless Security.
TL-WR702N ¾ 150Mbps Wireless N Nano Router SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address). But it is recommended strongly that you change your networks name (SSID) to a different value. This value is case-sensitive. For example, TEST is NOT the same as test.
TL-WR702N ¾ 150Mbps Wireless N Nano Router WDS Mode - This field determines which WDS Mode will be used. It is not necessary to change the WDS Mode unless you notice network communication problems with root AP. If you select Auto, then Router will choose the appropriate WDS Mode automatically. ¾ Security Type - This option should be chosen according to the AP's security configuration. It is recommended that the security type is the same as your AP's security type.
TL-WR702N 150Mbps Wireless N Nano Router Figure 7-9 Wireless Security ¾ Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. But it’s strongly recommended to choose one of the following modes to enable security. ¾ WEP - It is based on the IEEE 802.11 standard. • Type - you can choose the type for the WEP security on the pull-down list.
TL-WR702N 150Mbps Wireless N Nano Router • WEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identical on all wireless stations in your network. • Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption. "Disabled" means this WEP key entry is invalid. 64-bit - You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 ASCII characters.
TL-WR702N 150Mbps Wireless N Nano Router For ASCII, the key can be made up of any numbers 0 to 9 and any letters A to Z, the length should be between 8 and 63 characters. For Hexadecimal, the key can be made up of any numbers 0 to 9 and letters A to F, the length should be between 8 and 64 characters. Please also note the key is case sensitive, this means that upper and lower case keys will affect the outcome. It would also be a good idea to write down the key and all related wireless security settings.
TL-WR702N 150Mbps Wireless N Nano Router Figure 7-11 DHCP Settings Figure 7-12 DHCP Settings ¾ DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually. ¾ Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address.
TL-WR702N 150Mbps Wireless N Nano Router amount of time in minutes and the user will be "leased" this dynamic IP Address. After the time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. ¾ Default Gateway (Optional) - It is suggested to input the IP address of the LAN port of the Router. The default value is 192.168.0.254. ¾ Default Domain (Optional) - Input the domain name of your network.
TL-WR702N 7.7.3 150Mbps Wireless N Nano Router Address Reservation Choose menu “DHCP → Address Reservation”, and then you can view and add a reserved address for clients via the next screen (shown in Figure 7-14).When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings.
TL-WR702N 2. Modify the information. 3. Click the Save button. 150Mbps Wireless N Nano Router Click the Enable/Disabled All button to make all entries enabled/disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page and Click the Previous button to return the previous page. 7.
TL-WR702N Figure 7-17 ¾ 150Mbps Wireless N Nano Router Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. • Traceroute - This diagnostic tool tests the performance of a connection. ) Note: You can use ping/traceroute to test both numeric IP address or domain name.
TL-WR702N ¾ 150Mbps Wireless N Nano Router Traceroute Max TTL - The max number of hops for a Traceroute connection. The default is 20. Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 7-18 Diagnostic Results ) Note: Only one user can use this tool at one time.
TL-WR702N 2. 150Mbps Wireless N Nano Router Type the path and file name of the update file into the File field, or click the Browse button to locate the update file. 3. Click the Upgrade button. ) Note: 1. New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use.
TL-WR702N 7.8.4 150Mbps Wireless N Nano Router Backup & Restore Choose menu “System Tools → Backup & Restore”, and then you can save the current configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 7-21. Figure 7-21 Backup & Restore Configuration ¾ Click the Backup button to save all configuration settings as a backup file in your local computer. ¾ To upgrade the Router's configuration, follow these instructions.
TL-WR702N 150Mbps Wireless N Nano Router • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically). • Restore the Router's settings to factory defaults (system will reboot automatically). • Update the configuration with the file (system will reboot automatically. 7.8.
TL-WR702N 7.8.7 150Mbps Wireless N Nano Router System Log Choose menu “System Tools → System Log”, and then you can view the logs of the Router. Figure 7-24 System Log ¾ Refresh - Refresh the page to show the latest log list. ¾ Clear All - All the logs will be deleted from the Router permanently, not just from the page.
TL-WR702N 150Mbps Wireless N Nano Router Chapter 8. Configuration for Client Mode This chapter will show each Web page's key functions and the configuration way for Client Mode of TL-WR702N. 8.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions.
TL-WR702N 150Mbps Wireless N Nano Router Figure 8-2 Status ¾ Firmware Version - The version information of the Router’s firmware. ¾ Hardware Version - The version information of the Router’s hardware. ¾ LAN - This field displays the current settings or information for the LAN, you can configure them in the Network > LAN page. • MAC address - The physical address of the Router, as seen from the LAN. • IP address - The LAN IP address of the Router.
TL-WR702N 150Mbps Wireless N Nano Router 8.4 Working Mode The Router supports five operation mode types: AP, Router, Repeater, Bridge and Client. Please select one your want. Click Save to save your choice, which is shown as Figure 8-3. Figure 8-3 Working Mode ¾ AP - The wireless access point mode. ¾ Router - The wireless Router Mode. In this mode, the device enables multi-user to share Internet via DSL/Cable Modem. The only wired port works as WAN. ¾ Repeater - The wireless Repeater Mode.
TL-WR702N 8.5.1 150Mbps Wireless N Nano Router LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 8-6 LAN ¾ Address Type - Choosing Smart IP(DHCP) to get IP address from DHCP server, or choosing Static IP to configure IP address manually. ¾ MAC Address - The physical address of the LAN ports, as seen from the LAN. The value can't be changed.
TL-WR702N 8.6.1 150Mbps Wireless N Nano Router Wireless Settings Choose menu “Wireless → Wireless Settings”, and then you can configure the basic settings for the wireless network on this page. Figure 8-8 Wireless Settings - Client ¾ SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network.
TL-WR702N ¾ 150Mbps Wireless N Nano Router WDS Mode - This field determines which WDS Mode will be used. It is not necessary to change the WDS Mode unless you notice network communication problems with root AP. If you select Auto, then Router will choose the appropriate WDS Mode automatically. ¾ Security Type - This option should be chosen according to the AP's security configuration. It is recommended that the security type is the same as your AP's security type.
TL-WR702N 8.7.1 150Mbps Wireless N Nano Router DHCP Settings Choose menu “DHCP → DHCP Settings”, and you can see the page as shown in Figure 8-10, if you have chose Smart IP(DHCP) in Network → LAN, in which situation the device will help you configure the DHCP automatically as you need. If you have chose Static IP in Network → LAN, you can see the page as shown in Figure 8-11, and then you can configure the DHCP Server on this page.
TL-WR702N ¾ 150Mbps Wireless N Nano Router DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually. ¾ Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address. ¾ End IP Address - Specify an IP address for the DHCP Server to end with when assigning IP addresses. 192.168.0.
TL-WR702N 150Mbps Wireless N Nano Router ¾ Assigned IP - The IP address that the Router has allocated to the DHCP client ¾ Lease Time - The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. You cannot change any of the values on this page. To update this page and to show the current attached devices, click the Refresh button. 8.7.
TL-WR702N 150Mbps Wireless N Nano Router Figure 8-14 Add or Modify an Address Reservation Entry To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2. Modify the information. 3. Click the Save button. Click the Enable/Disabled All button to make all entries enabled/disabled Click the Delete All button to delete all entries.
TL-WR702N Figure 8-16 ¾ 150Mbps Wireless N Nano Router Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. • Traceroute - This diagnostic tool tests the performance of a connection. ) Note: You can use ping/traceroute to test both numeric IP address or domain name.
TL-WR702N ¾ 150Mbps Wireless N Nano Router Traceroute Max TTL - The max number of hops for a Traceroute connection. The default is 20. Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 8-17 Diagnostic Results ) Note: Only one user can use this tool at one time.
TL-WR702N 2. 150Mbps Wireless N Nano Router Type the path and file name of the update file into the File field, or click the Browse button to locate the update file. 3. Click the Upgrade button. ) Note: 1. New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use.
TL-WR702N 8.8.4 150Mbps Wireless N Nano Router Backup & Restore Choose menu “System Tools → Backup & Restore”, and then you can save the current configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 8-20. Figure 8-20 Backup & Restore Configuration ¾ Click the Backup button to save all configuration settings as a backup file in your local computer. ¾ To upgrade the Router's configuration, follow these instructions.
TL-WR702N 150Mbps Wireless N Nano Router • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically). • Restore the Router's settings to factory defaults (system will reboot automatically). • Update the configuration with the file (system will reboot automatically. 8.8.
TL-WR702N 8.8.7 150Mbps Wireless N Nano Router System Log Choose menu “System Tools → System Log”, and then you can view the logs of the Router. Figure 8-23 System Log ¾ Refresh - Refresh the page to show the latest log list. ¾ Clear All - All the logs will be deleted from the Router permanently, not just from the page.
TL-WR702N 150Mbps Wireless N Nano Router Appendix A: FAQ 1. How do I configure the Router to access the Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the WAN port on the Router. The telephone cord plugs into the Line port of the ADSL Modem. 3) Log in to the Router, click the “Network” menu on the left of your browser, and click "WAN" submenu.
TL-WR702N 2. 150Mbps Wireless N Nano Router How do I configure the Router to access the Internet by Ethernet users? 1) Log in to the Router, click the “Network” menu on the left of your browser, and click "WAN" submenu. On the WAN page, select “Dynamic IP” for "WAN Connection Type", finish by clicking Save. 2) Some ISPs require that you register the MAC Address of your adapter, which is connected to your cable/DSL Modem during installation.
TL-WR702N Figure A-4 Figure A-5 150Mbps Wireless N Nano Router Virtual Servers Add or Modify a Virtual server Entry ) Note: Your opposite side should call your WAN IP, which is displayed on the “Status” page. 4) How to enable DMZ Host: Log in to the Router, click the “Forwarding” menu on the left of your browser, and click "DMZ" submenu. On the "DMZ" page, click Enable radio button and type your IP address into the “DMZ Host IP Address” field, using 192.168.0.
TL-WR702N 4. 150Mbps Wireless N Nano Router I want to build a WEB Server on the LAN, what should I do? 1) Because the WEB Server port 80 will interfere with the WEB management port 80 on the Router, you must change the WEB management port number to avoid interference. 2) To change the WEB management port number: Log in to the Router, click the “Security” menu on the left of your browser, and click "Remote Management" submenu.
TL-WR702N Figure A-9 5. 150Mbps Wireless N Nano Router Add or Modify a Virtual server Entry The wireless stations cannot connect to the Router. 1) Make sure the "Enable Wireless Router Radio" is checked. 2) Make sure that the wireless stations' SSID accord with the Router's SSID. 3) Make sure the wireless stations have right KEY for encryption when the Router is encrypted. 4) If the wireless connection is ready, but you can’t access the Router, check the IP Address of your wireless stations.
TL-WR702N 150Mbps Wireless N Nano Router Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if necessary. 1. Configure TCP/IP component 1) On the Windows taskbar, click the Start button, and then click Control Panel. 2) Click the Network and Internet Connections icon, and then click on the Network Connections tab in the appearing window.
TL-WR702N 150Mbps Wireless N Nano Router Figure B-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.
TL-WR702N 150Mbps Wireless N Nano Router Figure B-3 ) Note: For Windows 98 OS or before, the PC and Router may need to be restarted. ¾ Setting IP address manually 1 Select Use the following IP address radio button. And the following items available 2 If the Router's LAN IP address is 192.168.0.254, specify the IP address as 192.168.0.x (x is from 1 to 253), and the Subnet mask as 255.255.255.0. 3 Type the Router’s LAN IP address (the default IP is 192.168.0.254) into the Default gateway field.
TL-WR702N Now: Click OK to keep your settings.
TL-WR702N 150Mbps Wireless N Nano Router Appendix C: Specifications General Standards IEEE 802.11n, 802.11b, 802.11g Protocols TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP Port One 10/100Mbps LAN/WAN port, one USB port 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) Cabling Type 100BASE-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) LED SYS Dimensions (L×W×H) 57mm×57mm×18mm Safety & Emissions FCC, CE Wireless Frequency Band 2.
TL-WR702N 150Mbps Wireless N Nano Router Appendix D: Glossary ¾ 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium (EWC) [3] was formed to help accelerate the IEEE 802.
TL-WR702N ¾ 150Mbps Wireless N Nano Router PPPoE (Point to Point Protocol over Ethernet) - PPPoE is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection. ¾ SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID.
