Archer CR700 AC1750 Wireless Dual Band Gigabit DOCSIS 3.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Korea Warning Statements: 당해 무선설비는 운용중 전파혼신 가능성이 있음.
z Avoid water and wet locations.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: AC1750 Wireless Dual Band Gigabit DOCSIS 3.0 Cable Modem Router Model No.
CONTENTS Chapter 1. Product Overview...................................................................................1 1.1 Overview of the Modem Router ...................................................................................... 1 1.2 Main Features................................................................................................................. 2 1.3 Panel Layout...................................................................................................................
3.4.8 RIP Setup........................................................................................................................... 18 3.5 Firewall ......................................................................................................................... 19 3.5.1 Basic .................................................................................................................................. 19 3.5.2 Local Log.....................................................................
Appendix A: Specifications ...................................................................................38 Appendix B: Technical Support ............................................................................
Archer CR700 User Guide Chapter 1. Product Overview Thank you for choosing the Archer CR700 AC1750 Wireless Dual Band Gigabit DOCSIS 3.0 Cable Modem Router. 1.1 Overview of the Modem Router The Archer CR700 AC1750 Wireless Dual Band Gigabit DOCSIS 3.0 Cable Modem Router integrates DOCSIS 3.0 modem, NAT router, 4-port switch and wireless access point in one device provides a one-stop networking solution. The modem router provides up to 450Mbps (2.
Archer CR700 User Guide 1.2 Main Features ¾ Supports 802.11ac - The next generation of Wi-Fi ¾ Dual band – for combined wireless speeds of up to 1.75Gbps at 2.4GHz and 5GHz band concurrently ¾ DOCSIS 3.0/EuroDOCSIS 3.0, Compatible with DOCSIS/EuroDOCSIS 2.0/1.1/1.0 ¾ 16 Downstream Channel bonding, Up to 680Mbps Downstream for DOCSIS and 900Mbps for EuroDOCSIS ¾ 4 Upstream Channel bonding, Up to 120Mbps Upstream ¾ Full Band Capture windows - Utilize any channels in the downstream spectrum.
Archer CR700 User Guide 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The modem router’s LEDs are located on the side panel (View from top to bottom). They indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name Status On (Power) Off Orange (Downstream) White Flash Off Orange (Upstream) (Online) Indication The modem router is powered on. The modem router is off. Please ensure that the power adapter is connected correctly.
Archer CR700 (LAN) Off On (Wireless) Off On User Guide There is no device connected to this LAN port. Wireless is enabled. The modem router is working on 2.4GHz/5 GHz radio band. Wireless is disabled. A wireless device has been successfully added to the network by WPS function. WPS handshaking is in process and will continue for about 2 (WPS) Flash that you want to add to the network while the LED is flashing. Off (USB on the back panel) minutes.
Archer CR700 User Guide ¾ WPS: The switch for the WPS function. ¾ WiFi ON/OFF: The switch for the WiFi function. Press it to enable/disable the WiFi function. ¾ USB2, USB1: The USB port connects to a USB storage device or a USB printer. ¾ LAN4/WAN, LAN3, LAN2, LAN1: Through these ports, you can connect the modem router to your PC or the other Ethernet network devices. ¾ Cable: ¾ DC: The power plug where you will connect the power adapter. ¾ Power ON/OFF: The switch for the power.
Archer CR700 User Guide Chapter 2. Connecting the Modem Router 2.1 System Requirements ¾ Broadband Internet Access Service (DSL/Cable/Ethernet). ¾ PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors. ¾ TCP/IP protocol on each PC. ¾ Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. 2.2 Installation Environment Requirements ¾ ¾ ¾ ¾ ¾ The Product should not be located where it will be exposed to moisture or excessive heat.
Archer CR700 User Guide Figure 2-1 2.4 Test Your Internet Connection Please open the web browser and try to log on to http://www.tp-link.com to test your Internet connection.
Archer CR700 User Guide Chapter 3. Configuring the Modem Router This chapter will show configuration for the key functions on the Web-based management page. 3.1 Login After your successful login, you will see the ten main menus on the left of the Web-based management page. On the right, there are the corresponding explanations and instructions. The detailed explanations for each Web page’s key function are listed below. 3.
Archer CR700 User Guide Figure 3-1 3.3 Basic Choose “Basic”, there are many submenus under the main menu. Click any one of them, and you will be able to configure the corresponding function.
Archer CR700 User Guide 3.3.1 Setup Choose “Basic”Æ“Setup”, and you will be able to configure LAN and WAN settings related to your ISP's connection. Figure 3-2 After you finish the configuration, please click Save to make the settings take effect. 3.3.2 DHCP Choose menu “Basic”Æ“DHCP”, you can configure the DHCP Server on the page as shown in Figure 3-3.
Archer CR700 User Guide Figure 3-3 ¾ Lease Time: The Leased Time is the amount of time in which a network user will be allowed connection to the modem router with their current dynamic IP address. Enter the amount of time, in hours, then the user will be “leased” this dynamic IP address. After the dynamic IP address has expired, the user will be automatically assigned a new dynamic IP address. The default is 3600 minutes. Click the Apply button to save your settings.
Archer CR700 User Guide Figure 3-4 3.3.4 LAN IPv6 Choose “Basic”Æ“LAN IPv6” menu, and you will see the LAN screen (shown in Figure 3-5). Figure 3-5 3.3.5 DDNS Choose “Basic”Æ“DDNS” and you can configure the Dynamic DNS function.
Archer CR700 User Guide Figure 3-6 ¾ Service Provider: This field displays the service provider of DDNS. ¾ Username & Password: Type the “User Name” and “Password” for your DDNS account. ¾ Login/ Logout: Login to or logout of the DDNS service. 3.3.6 Backup Choose menu “Basic” → “Backup e”, and then you can save the current configuration of the modem router as a backup file and restore the configuration via a backup file as shown in Figure 3-7.
Archer CR700 User Guide 2) Click Browse to select the path name where you save the downloaded file on the computer into the File Name blank. 3) Click the Upgrade button. 4) The modem router will reboot while the upgrading has been finished. ) Note: 1) New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use.
Archer CR700 User Guide ) Note: All changed settings will be lost when defaults are restored. 3.4 Advanced Choose “Advanced”, there are many submenus under the main menu. Click any one of them, and you will be able to configure the corresponding function. 3.4.1 Options This page allows configuration of advanced features of the broadband gateway.
Archer CR700 User Guide 3.4.2 IP Filtering This page allows configuration of IP address filters in order to block internet traffic to specific network devices on the LAN. Figure 3-12 3.4.3 MAC Filtering This page allows configuration of MAC address filters in order to block internet traffic to specific network devices on the LAN. This feature only applies to IPv4 traffic. Figure 3-13 3.4.
Archer CR700 User Guide Figure 3-14 3.4.5 Forwarding This allows for incoming requests on specific port numbers to reach web servers, FTP servers, mail servers, etc. so they can be accessible from the public internet. A table of commonly used port numbers is also provided. Figure 3-15 3.4.6 Port Triggers Choose menu “Advanced”→ ”Port Triggers”, you can view and add port trigger in the screen as shown in Figure 3-16.
Archer CR700 User Guide Figure 3-17 3.4.7 DMZ Host Choose menu “Advanced→DMZ Host”, and then you can view and configure DMZ host in the screen (shown in Figure 3-18).The DMZ host feature allows one local host to be exposed to the Internet for a special-purpose service such as Internet gaming or videoconferencing. The modem router forwards packets of all services to the DMZ host.
Archer CR700 User Guide Figure 3-19 3.5 Firewall Choose “Firewall”, there are several submenus under the main menu. Click any one of them, and you will be able to configure the corresponding function. 3.5.1 Basic Choose menu “Firewall” → “Basic”, and then you can configure the firewall features. It is highly recommended that the Firewall is left enabled at all times for protection against Denial of Service attacks. Figure 3-20 3.5.
Archer CR700 User Guide Figure 3-21 3.5.3 Remote Log This page allows optional configuration of events to be sent to a local SysLog server. Figure 3-22 3.6 Parental Control Choose “Parental Control”, there are several submenus under the main menu. Click any one of them, and you will be able to configure the corresponding function. 3.6.1 Basic Setup This page allows basic selection of rules which block certain Internet content and certain Web sites.
Archer CR700 User Guide "Add" or "Remove" button for your new settings to take effect. If you refresh your browser's display, you will see the currently active settings. Figure 3-23 3.6.2 User Setup This page allows configuration of users. 'White List Only' feature limits the user to visit only the sites specified in the Allowed Domain List of his/her content rule.
Archer CR700 User Guide Figure 3-24 3.6.3 ToD Filter This page allows configuration of time access policies to block all internet traffic to and from specific network devices based on time of day settings.
Archer CR700 User Guide Figure 3-25 3.6.4 Event Log This page displays Parental Control event log reporting. Figure 3-26 3.7 VPN Choose “VPN”, there are several submenus under the main menu. Click any one of them, and you will be able to configure the corresponding function. 3.7.1 Basic Choose “VPN”Æ“Basic”, you can Add/Remove or Enable/Disable the IPSec tunnel connections on the screen as shown in Figure 3-27. Figure 3-27 3.7.
Archer CR700 Figure 3-28 The topology is as follows.
Archer CR700 User Guide ) Note: You could also use other VPN Routers to set VPN tunnels with Archer CR700. Archer CR700 supports up to 10 VPN tunnels simultaneously. 3.7.3 Event Log This page allows you to view the VPN Event Log. Figure 3-29 3.8 Wireless 2.4GHz There are six submenus under the Wireless 2.4GHz menu. Click any of them, and you will be able to configure the corresponding function.
Archer CR700 User Guide 3.8.1 Basic Choose menu “Wireless 2.4GHz” → “Basic”, you can configure the basic settings for the wireless network of 2.4GHz on this page. Figure 3-30 ¾ 802.11 Mode: Select the desired mode. It is strongly recommended that you set the Mode to 802.11b/g/n mixed, and all of 802.11b, 802.11g, and 802.11n wireless stations can connect to the modem router. ¾ Bandwidth: Select the channel width from the drop-down list.
Archer CR700 User Guide Figure 3-31 3.8.3 Guest Network This feature allows you to create a separate network for your guests without allowing them to access your main network and the computers connected to it. Figure 3-32 3.8.4 Advanced This page allows configuration of data rates and WiFi thresholds.
Archer CR700 User Guide Figure 3-33 3.8.5 Bridging This page allows configuration of WDS features. Figure 3-34 3.8.6 Access Control This page allows configuration of the Access Control to the AP as well as status on the connected clients. Figure 3-35 3.9 Wireless 5GHz There are six submenus under the Wireless 5GHz menu. Click any of them, and you will be able to configure the corresponding function.
Archer CR700 User Guide 3.9.1 Basic Choose menu “Wireless5GHz” → “Basic”, you can configure the basic settings for the wireless network of 5GHz on this page. Figure 3-36 3.9.2 Primary Network This page allows configuration of the Primary Wireless Network and its security settings.
Archer CR700 3.9.3 Guest Network This page allows configuration of a guest network. Figure 3-38 3.9.4 Advanced This page allows configuration of data rates and WiFi thresholds. Figure 3-39 3.9.5 Bridging This page allows configuration of WDS features.
Archer CR700 User Guide 3.9.6 Access Control This page allows configuration of the Access Control to the AP as well as status on the connected clients Figure 3-41 3.10 USB Settings There are five submenus under the USB menu. Click any of them, and you will be able to configure the corresponding function. 3.10.
Archer CR700 User Guide Figure 3-42 3.10.2 User Accounts You can specify the user name and password for Storage Sharing and FTP Server users on this page. Storage Sharing users can access the folders by entering the following URL into the address field of your browser or Windows Explorer, such as. \\192.168.1.1. FTP Server users can log into the FTP Server via FTP Client. There are five users here, which provide means to control the access to the USB mass storage by Storage Sharing or FTP.
Archer CR700 User Guide To delete an existing user account, please click Delete in the Action column. 3.10.3 Storage Sharing Choose menu “USB” → ”Storage Sharing”, you can configure a USB disk drive attached to the modem router and view volume and share properties on this page as shown below. Figure 3-44 ¾ Server Status: Indicates the Storage Sharing's current status.
Archer CR700 User Guide Figure 3-45 2. Click the Browse button, and then select the Select Volume from the drop-down list. 3. Enter display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings. You can click the upper button to go to the upper folder Click the Enable/Disable Selected button to enable or disable the selected entries. Click the Delete Selected button to delete the selected entries. ) Note: 1. The max share folders number is 10.
Archer CR700 User Guide Figure 3-46 ¾ Server Status: Indicates the FTP Server's current status. ¾ Internet Access: If Internet Access is enabled, user(s) in public network can access FTP server via Internet Address. ¾ Internet Address: If Internet Access is enabled, WAN IP will be displayed here. ¾ Service Port: Enter the FTP Port number to use. The default is 21. ¾ Share Name: This folder's display name. ¾ Directory: The real full path of the specified folder.
Archer CR700 User Guide Figure 3-47 2. Click the Browse button, and then select the Select Volume from the drop-down list. 3. Enter display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings. You can click the upper button to go to the upper folder. Click the Enable/Disable Selected button to enable or disable the selected entries. Click the Delete Selected button to delete the selected entries. ) Note: 1. The max share folders number is 10.
Archer CR700 User Guide Figure 3-48 ) Note: The max share folders number is 6. If you want share a new folder when the numbers has been reached to be 6, you can delete a share folder and then add a new one. 3.11 Logout Choose “Logout”, and you see the screen as shown in Figure 3-49. Click Back to Login and you will be redirect to the login screen.
Archer CR700 User Guide Appendix A: Specifications HARDWARE FEATURES IEEE Standards IEEE 802.3, 802.3u Certification CE, FCC, RoHS, CableLabs DOCSIS Standards DOCSIS 3.0/EuroDOCSIS 3.0 DOCSIS 2.0/EuroDOCSIS 2.0 DOCSIS 1.1/EuroDOCSIS 1.1 DOCSIS 1.0/EuroDOCSIS 1.0 Interface 1 F-Connector, female 75 Ω 4 10/100/1000Mbps RJ45 LAN Ports 2 USB 2.0 Ports Button 1 Power On/Off¬ Button 1 Wi-Fi On/Off¬ Button 1 WPS Button 1 Reset Button External Power Supply 12VDC/3.
Archer CR700 Storage Temperature -40℃ ~ 70℃ Storage Humidity 5% ~ 90% RH (non-condensing) 39 User Guide
Archer CR700 User Guide Appendix B: Technical Support Technical Support For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq To download the latest Firmware, Driver, Utility and User Guide, go to: http://www.tp-link.com/en/support/download For all other technical support, please contact us by using the following details: Global Tel: +86 755 2650 4400 Fee: Depending on rate of different carriers, IDD. E-mail: support@tp-link.
