OPERATION PANEL Timer Key Digital Indicator Key-lock Button Adjustment Keys ON/OFF Lamp — flashing : ON/OFF Button/Lamp Preheating mode constant : Heater in operation key-lock Indicator — constant : Childproof Lock is on. Temperature Indicator — constant : The Digital Indicator shows temperature and Room temperature. Clock Indicator — constant : The Digital Indicator shows current time. Timer Lamp — constant : Heater in operation in timer mode.
UNPACKING AND PLACEMENT 1. Take out heater from box carefully to avoid damage. 2. Remove all packing materials from heater. 3. Make sure all screws are tight and all parts intact. NOTE: Save shipping carton and all packing materials for future storage of your heater. 4. When positioning your heater for use, keep it away from walls and all other materials as illustrated below. 150 cm 20 cm 50 cm 50 cm 150 cm 5. The floor should be firm and completely level. Reposition the heater, when it is not level.
FUELING WARNING : Use only water-clear kerosene (paraffin). Never use gasoline or other flammable liquids. ALWAYS extinguish heater before refill heater fuel tank. Fuel heater outside the living area. 1. Open the fuel tank lid on the top of heater cabinet and lift out the removable fuel tank. Turn the removable tank upside down and remove the fuel tank cap. 2. Insert the straight tube of the manual siphon into the jerrycans; insert the siphon’s flexible hose into the removable fuel tank opening. 3.
OPERATION CAUTION : Always make sure that there is sufficient ventilation. SET CLOCK It is only possible to set the correct time, when the heater is connected to the mains and not burning. 1. Use the Adjustment Keys ( ▼ hour / ▲ min.) to set the time. 2. To set the time, press “hour” and “min.” set buttons. Individual motions will increase the time by one unit; holding continuously will raise either the “hour” or “min.” rapidly.
TIMER IGNITION Your heater can be arranged to ignite automatcally at a chosen time by use of a pre-set “Timer”. This “Timer” can only be set after the clock setting has been completed. 1 2 3 4 1. Press the button and then the “Timer” key immediately after that. The Timer Lamp and Digital Indicator will start blinking. 2. To set the “Timer” to the chosen igntion time, you should follow the same procedure as given earlier for “Clock” time setting.
TEMPERATURE REGULATION 1. Use the Adjustment keys ( ▼ hour / ▲ min.) to adjust the temperature. 2. Adjust the temperature using the key on the right ( ▲ min.) to set the temperature to a higher setting and the key on the left ( ▼ hour ) to lower the temperature. 3. Until the room temperature has reached the set temperature, the heater will burn at either high or medium burning mode.
CHILDPROOF LOCK The childproof lock can be used to prevent children accidentally changing the heater settings. When the heater is burning and the childproof lock is on, the heater can only be switched off. Other functions are blocked then. If the heater has already been switched off, the childproof lock also prevents accidental ignition of the heater. Activate the childproof lock by pressing the Key-lock button and holding it down for more 3 seconds.
AUTOMATIC CLEANING MODE When the heater has been burning continuously for two hours at its highest setting, the burner will automatically start an autoclean procedure. The display will show the autocleaningcode running back to . The procedure takes 5 minutes, during which the heater will burn at its lowest setting, while the burner autocleans. When the burner is clean again, the heater will automatically switch back to the highest setting again.
EMERGENCY MESSAGE In the event that heater should extinguish itself, without any action or your part, you should look to the digital indicator for any of the following messages. MESSAGE (Digital Indicator) e-0 f-0 e- 1 f- 1 e-2 e-5 e-6 e-7 e-8 e-9 MESSAGE MEANING Temperature within the heater too high. Power interrupted. You can re-ignite the heater. Thermostat is broken or disconnected. Contact your dealer. Faulty burner thermistor. Contact your dealer.
ROUTINE MAINTENANCE CAUTION: Be sure to unplug heater before performing any checks or cleaning. CAUTION: Do not remove any parts from the heater except removable fuel tank, fuel acceptance fitting and air filter. WARNING: Allow heater to cool completely before cleaning or maintenance. 1. Clean Air Filter Clean the air filter with a vacuum cleaner on a weekly basis. If filter is clogged with dust or lint, smoking and improper combustion may result.
TROUBLESHOOTING Should problems arise during operation or ignition, use this chart to determine the cause and the proper steps to take. Be sure to unplug heater and allow to cool completely before taking corrective measures. PROBLEM CAUSE SOLUTION POWER LAMP FAILS — Disconnected power plug TO TURN ON — Incorrect wiring — Circuit board malfunction — Plug into 230V AC outlet. — Consult your dealer. — Consult your dealer.
LONG TERM STORAGE At the end of the heating season, you must store the heater in a dust-free plece, if possible in its original packaging. The following procedures are recommended. 1. Drain Fuel Tank Remove any kerosene (paraffin), dust or water remaining in the fuel sub tank and removable fuel tank to prevent rusting. 2. Clean Heater Wipe off any dirt or dust on heater with a damp cloth, then wipe again using a dry cloth. 3.
TOYOTOMI CO., LTD. 5-17, Momozono-cho, Mizuho-ku, Nagoya, Japan New 08/11 REV.
