User manual

Learning new transmitter codes
With short pressing of the programming key on the receiver the 'learning
mode' is entered:
programming key LED function
press short Ch 1 LED blinking Learning codes for Ch1
press short again Ch 2 LED blinking Learning codes for Ch2
press short again Ch 3 LED blinking Learning codes for Ch3
press short again Ch 4 LED blinking Learning codes for Ch4
press short again LEDs off exit learning mode
In learning mode the receiver is waiting for codes received from
transmitters. If no code is received for about 10 seconds, the receiver will
exit learning mode and return to normal operation mode. If a code is
received during learning mode, it is stored to memory and both LEDs will
flash for confirmation.
Configuration of each channel for toggle or timer mode
By keeping the programming button pressed for longer duration the
configuration mode can be selected according to this procedure:
first step: choose channel
press programming
key and...
LED-Anzeige Funktion
release, after... Ch1 LED is lit setup mode for Ch1
release, after... Ch2 LED is lit setup mode for Ch2
release, after... Ch3 LED is lit setup mode for Ch3
release, after... Ch4 LED is lit setup mode for Ch4
second step: choose desired mode
The mode of operation can be choosen individually for both channesl.
While the LED of Ch1 or Ch2 is still lit from first step the programming
key is pressed again, and...
programming key LED function
pressed again, and ... slow blink sequence choosing mode
... release after 1
st
blink toggle mode
... release after 2
nd
blink 0,5 sec. timer
... release after 3
rd
blink 5 sec. timer
... release after 4
th
blink 30 sec. timer
... release after 5
th
blink 1 min. timer
... release after 6
th
blink 5 min. timer
... release after 7
th
blink 15 min. timer
... release after 8
h
blink 30 min. timer
... release after 9
th
blink 1 hour timer
Delete all transmitter codes from memory
For deleting all codes stored in the memory of the receiver the
programming key is held down until all four LEDs are lit together (after 6-
7 seconds). The key is released and pressed again to confirm the
deletion of the complete memory.
The completion of the memory formatting is confirmed with alternate
blinking of both LEDs
The setting of the toggle/timer mode for both channels is not affected by
this procedure.
Functions in normal operation mode
After learning codes from transmitters, all channels of the receiver can be
controlled independent of each other according to the configured
operation modes.
The yellow LED for channels 1-4 indicate the current status of the
associated relay.
If the LED is lit, the terminals 'NO' and 'C' of this channel are connected
electrically.
If the LED is dark, the terminals 'NC' and 'C' of this channel are connected
electrically
Note about maximum range to be obtained:
The functional range is up to 50 meters under best conditions but could be
limited by objects blocking the line of sight between transmitter and
receiver. Other RF-noise on the same frequency (e.g. from babyphone,
wireless thermometer, or other 433MHz devices) could also limit the
effective range of the remote set.
External Antenna Connector
The 3 pin header on the right side of the terminal block for power supply is
for the connection of an optional external receiver unit available at
Conrad with BN xxxxx. If not using the external receiver, please leave this
connector open.
Mounting Instructions
The 4-ch remote receiver could be mounted on almost any even surface,
mounting on metal may have bad effect on functional range.Using the
included mounting clips, the case can be snapped onto DIN-mounting rails
with 30mm width
Declaration of conformity
Hereby, Conrad Electronic SE, Klaus-Conrad-Straße 1, 922 40 Hirschau,
declares that this product is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
The declaration of conformity to this product can be found at
www.conrad.com.
19 14 01 – GB - REV 1.0 / 06.2012