Instruction Manual

ManualsBrandsTOUGH COUNTRY ManualsFront BumperTOUGH COUNTRY TFR2017F Custom Traditional Front Bumper

www.toughcountry.com

INSTALLATION INSTRUCTIONS

Tough Country Products

1101 N. Blue Creek Rd

El Campo, TX 77437

Phone: 1-877-44TOUGH

Fax: 979-543-7209

2017-2022 Ford F250-F350

Front Replacement

TFR2017F, EFR2017F

BUMPER REMOVAL INSTRUCTIONS:

1. MAKE SURE TRUCK IS OFF AND BATTERY IS DISCONNECTED

2. UNPLUG WIRING HARNESS FOR FOGLIGHTS. *(IF EQUIPPED) *(AND ADAPTIVE CRUISE IF

EQUIPPED)

3. REMOVE BUMPER SUPPORT BOLTS FROM UNDERNEATH BY FENDER ON EACH SIDE OF TRUCK.

4. REMOVE THE 4 BUMPER MOUNTING BOLTS ON EACH SIDE.

[*NOTE: AFTER REMOVING THE FIRST BOLT, INSERT SCREWDRIVER INTO BOLT HOLE TO PREVENT NUT PLATE

FROM SPINNING WHILE REMOVING SECOND BOLT.]

5. CAREFULLY REMOVE BUMPER.

6. REMOVE FACTORY TOW LOOPS (IF EQUIPPED) & BRACKETS ON FRAME BEHIND TOW LOOPS

7. REMOVE (METAL) AIR DAM SCOOPS (IF EQUIPPED)

INSTALLATION OF TOUGH COUNTRY REPLACEMENT BUMPER WITH FOG LIGHTS:

*NOTE* (IF EQUIPPED WITH FOGLIGHTS) SEE PICTURE AT TOP OF PAGE 2 TO DETERMINE WHICH FOG

LIGHT YOU HAVE

1. FOGLIGHT A)

 UNINSTALL LIGHT FROM FACTORY BUMPER. USING A SCREWDRIVER, REMOVE

FOG LIGHT BUTTONS FROM BRACKET.

 REMOVE AJUSTMENT BOLT AND PLASTIC NUT WITH SPRING. DISCARD BRACKET.

 TO INSTALL THIS LIGHT, IT REQUIRES THE BACK PLATE TO BE INSTALLED FOR

USE IN THE BUMPER.

 INSERT LIGHT INTO BUMPER ALIGNING THE HOLE ON THE TOP AND INSERT PINS.

INSTALL PLASTIC NUT ON THE BOTTOM BRACKET. REINSTALL SPRING AND BOLT

 TIGHTEN. (BELOW ARE BRACKETS NEEDED TO INSTALL FOGLIGHT A)

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Tough Country Products 1101 N. Blue Creek Rd El Campo, TX 77437 Phone: 1-877-44TOUGH Fax: 979-543-7209 2017-2022 Ford F250-F350 Front Replacement TFR2017F, EFR2017F BUMPER REMOVAL INSTRUCTIONS: 1. MAKE SURE TRUCK IS OFF AND BATTERY IS DISCONNECTED 2. UNPLUG WIRING HARNESS FOR FOGLIGHTS. *(IF EQUIPPED) *(AND ADAPTIVE CRUISE IF EQUIPPED) 3. 4. REMOVE BUMPER SUPPORT BOLTS FROM UNDERNEATH BY FENDER ON EACH SIDE OF TRUCK. REMOVE THE 4 BUMPER MOUNTING BOLTS ON EACH SIDE.
PAGE 2
. FOGLIGHT B)  UNINSTALL LIGHT FROM FACTORY BUMPER (SET 4 FACTORY MOUNTING BOLTS TO THE SIDE FOR LATER USE)  INSTALL SUPPLIED T-BRACKET TO BACK OF THE FOG LIGHT USING FACTORY BOLTS SECURELY (DO NOT OVER TORQUE THESE)  INSTALL LIGHT TO BUMPER & ADJUST TO DESIRED LOCATION  REFERENCE PICTURE BELOW FOR WHAT INSTALLED LIGHT LOOKS LIKE A) B) 3. REPEAT FOR OPPOSITE SIDE. (THESE ARE THE 3 DIFFERENT LIGHT CONFIGURATIONS FOR THIS FOG LIGHT BUCKET) 2 www.toughcountry.
PAGE 3
INSTALLATION OF TOUGH COUNTRY REPLACEMENT BUMPER: 1. INSTALL SUPPLIED BRACKET TO BUMPER WITH SUPPLIED & BOLTS HAND TIGHTEN (IF TRUCK HAS FRONT CAMERA REMOVE MESH PIECE WITH SUPPLIED ALLEN WRENCH BEFORE NEXT STEP *DOES NOT APPLY TO WINCH MOUNT OR EVOLUTION) 2. INSTALL REPLACEMENT BUMPER USING SUPPLIED BOLTS IN THE HOLES ON THE FRAME. USE THE SUPPLIED IN THE FORMER TOW LOOP MOUNT POSITION HOLES. TIGHTEN SECURELY. ALIGN BUMPER AND TIGHTEN ALL BOLTS. 3.
PAGE 4
    3) INSTALL ADAPTIVE BOX & COVER USING SUPPLIED HARDWARE RECONNECT HARNESS NOTE THAT NOTHING SHOULD BE IN FRONT OF ADAPTIVE BOX AFTER INSTALLATION FOR PROPER FUNCTION *ON 2020 MODELS ADDITIONAL BRACKET FOR SMALLER UNIT IS REQUIRED (PICTURED ON PAGE 4) EFR2017FALW  FOR INSTALL OF ADAPTIVE CRUISE ON THIS PART NUMBER USE OF SUPPLIED ADAPTIVE KIT IS REQUIRED  INSTALLS TO DRIVERS SIDE FRONT OF BUMPER  INSTALL MOUNTING KIT TO PREDRILLED HOLES,  INSTALL ADAPTIVE BOX & COVER USING SUPPLIED HARDWARE 