Specification

INSTALLATION/APPLICATION
Refer to “2-Component Polyurethane Spray Foam Instructions for Use” found inside
the product carton or request a faxed set of these instructions by calling Customer
Service at 1-800-325-6180. Always refer to local building codes prior to
application of Touch ’n Foam Professional Spray Foam. All substrate surfaces
should be clean/dry and above 60°F (16°C) prior to application. Variance outside of
the recommended temperature can drastically affect the adhesion and yield of your
foam kit. Surfaces to be sprayed must be dry, clean and free of dust, dirt, grease and
other substances that may inhibit proper adhesion. Spray in layers at no more than 1
inch per layer.
IMPORTANT: CHECK 3 TEMPERATURES.
Low temperatures can affect foam performance.
Health & Safety Guidelines
Independent, 3rd party testing has demonstrated that spraying Touch ‘n Foam
Professional low pressure two-component spray foam does not produce airborne MDI
particulates in excess of the limits tested by either the American Conference of
Governmental Industrial Hygienists (ACGIH) or the Occupational Safety and Health
Administration (OSHA). Accordingly, tests indicated that with adequate ventilation, no
respirator is required to spray Convenience Products low pressure spray foam, but a
paint mask is recommended for dermal protection. For users who want to increase their
personal protection levels, air purifying respirators and full-body coveralls (such as
Tyvek suits) are available. OSHA provides additional information regarding training,
medical evaluation, and fit testing for respirators.
TECHNICAL DATA
Shelf Life
Fifteen months in unopened container when stored between 60°–90°F (16°–32°C),
in a dry, well-ventilated area. See expiration date on box. Use within 30 days after
initial start.
Storage & Disposal
Keep containers tightly closed in a cool, well-ventilated area. Ideal storage temperature is 60°–90°F (16°– 32°C). Storage above 90°F (32°C) will reduce shelf life. Do not store at temperatures
above 120°F (49°C). Do not expose containers to conditions that may damage, puncture, or burst the containers. Dispose of leftover material/containers in accordance with federal, state and local
regulations. See Material Safety Data Sheet for more information. Refer to “2-Component Polyurethane Spray Foam Instructions for Use” for storage of partially used kits.
KEEP OUT OF REACH OF CHILDREN.
WARRANTY: If product fails to perform when used as directed, within one year from the date of purchase, call 1-888-DAP-TIPS, with your sales receipt and product container
available, for replacement product or sales price refund. DAP will not be responsible for incidental or consequential damages.
TECHNICAL SERVICES: Technical assistance, including more detailed information, product literature, test results, assistance with preparing project specifications and application training is
available by contacting 1-888-DAP-TIPS.
SPRAY FOAM
LOW PRESSURE 2-COMPONENT
POLYURETHANE INSULATION
Attach color coded hoses. Calibrate foam in waste container. Deliver foam in a smooth, easy stream.
Shelf Life 15 months; expiration date on box
Theoretical Yield/Output*
System 15 up to 15 board feet (1.416 m
2
@ 25 mm)
System 200 200 board feet (18.88 m
2
@ 25 mm)
System 600 600 board feet (56.64 m
2
@ 25 mm)
Dry time/Tack Free Time 30–60 seconds
Cuttable 2–5 minutes
Fully Cured Approximately 1 hour
ASTM E84 Surface Burning Characteristics @ 2 in. (51 mm)
Flame Spread 20
Smoke Developed 350
ASTM G21 Fungi Resistance Does not support growth
ASTM E96 Water Vapor Transmission 1.77 perms @ 1 in. (25 mm)
0.98 perms @ 2 in. (51 mm)
ASTM E283 Air Barrier Properties - Insulate stud wall cavities (up to 2" thick)
@ 1.57 psf (75 Pa) < 0.001 CFM/ft
2
(0.002 L/s/m
2
)
ASTM D1621 Compressive Strength 31.0 psi (214 kPa)
ASTM D1622 Core Density 1.75 ± .10 pcf (28.0 ± 1.60 kg/m
3
)
ASTM D1623 Tensile Strength 30.8 psi (213 kPa)
ASTM D2126 Thermal and Humid Aging @ 2 wks Dimensional Stability
-4°F (-20°C) +0.9%
+158°F (+70°C) / 97% RH +5.7%
+176°F (+80°C) +1.6%
ASTM D6226 Closed Cell Content 94%
International Residential Code Compliant
California Bureau of Home Furnishings & Insulation Listed
ASTM E90 Sound Transmission Class STC 32 @ 1.5 in. (38 mm)**
ASTM C518 Aged R-Value 5.4 @ 1 in. (25 mm)
11.0 @ 2 in. (51 mm)
TYPICAL PROPERTIES
*A board foot is defined as a 12" x 12" square at 1" thick. Actual output can be affected by a number of factors, including
temperature and humidity. The theoretical yield has become an industry standard for identifying certain sizes of two-component
kits. Theoretical yield calculations are performed in perfect laboratory conditions, without taking into account the loss of blowing
agent or the variations in application methods and types.
**The STC (Sound Transmission Class) test wall assembly was comprised of 5/8" OSB (exterior), one layer of type X gypsum
wallboard (interior), 2 x 4 studs 16" OC with 1.5" of Touch ’n Foam Professional Spray Foam.
42007-1-051816-TNFP
CHEMICALS
(70°–90°F/21°–32°C)
70°F/21°C
(60°–90°F/16°–32°C)
60°F/16°C
(60°–90°F/16°–32°C)
60°F/16°C
SURFACES
AIR