Specification Sheet

Self-Generating EcoPower
®
System
Sensor Toilet Flush Valve, Concealed (4" x 4") - 1.6 GPF
S
PECIFICATIONS
Product TET3GN31#SS-Complete Set (1 1/2" V.B.), Back Spud Wall, Satin Finish
TET3GN32#SS-Complete Set (1 1/2" V.B.), Top Spud, Satin Finish
TET3GN33#SS-Complete Set (1 1/2" V.B.), Back Spud Floor, Satin Finish
Power supply Hydro-Power Charge, 10 years based on 12 flushes per day.
(backup battery: 4 years at 4,000 cycles per month without recharging)
Detection range Self-adjusting to environment
Detection time Factory setting at six (6) seconds minimum
Water supply
1" NPT
Discharge quantity Factory setting at 1.6 GPF/6.0 LPF
Toilet type Flushometer type bowl
Ambient temperature 32°-104°F (0°-40°C)
Supply water pressure 30 psi (flowing) - 125 psi* (a minimum flow rate of 23 GPM)
Trap seal protection Automatic flushes once after twenty-four (24) hours of non-use
Warranty Limited three (3) year warranty on all component parts. Details available upon request.
Listings
A.S.S.E. 1037
These dimensions and specifications are subject to change without notice.
*Water pressures over 80 psi are not recommended for most plumbing fixtures.
TOTO
®
Model No. _____________________________
Automatic infrared sensor activated, piston toilet flush
valve.Heavy-duty 4"x4" Stainless Steel coverplate with Satin
finish. Vandal resistant hex head screws. Automatic sensor
adjustment on installation. Manual override button. Piston
valve with stainless steel self-cleaning debris screen and
Solenoid with self-cleaning mechanism. Automatic flush every
twenty four hours if not used. Angle stop and vacuum breaker
included with accessories. Electrical Sensor Component
separated from water body of valve and sealed in waterproof
compartment. Through the use of TOTO's EcoPower
®
flush
valves, using the valve 12 flushes per day will fully recharge the
valve for up to 10 years.
SUGGESTED ENGINEERING SPECIFICATION:
DIAGRAM:
Dimensions: Inch
Facing of the wall Facing of the wall
6 - 7 ”
Top Spud Back Spud Floor Moun t Back Spud Wall Mount
x =At least 5” clearance from sensor to tip of toilet seat up
position or to top of grab bar is required to avoid false detection.
Always position the sensor above upright toilet seats and grab bars
x xx
TOTO
EcoPower®
Facing of the wall
Depending on
* Leave some room for elbow nut from the wall for future maintenance.
x
, the frame may not be centered to Supply as shown.
Trip Lever
5”
2 ”2 ”2 ”
SupplySupplySupply
16”16”
11”
frame
2¼” Min.
Bowl
Bowl
Bowl
(3-3/4"- 4-7/8") *(3-3/4"- 4-7/8") *(3-3/4"- 4-7/8") *
of
sensor
of
sensor
of
sensor
3”
*
+
Opening in Wall:
3 -
” x 3 - ”
3-
”
1- ¾”
4 - ¾”
4 ¾”
1 ¼”
Supply to
Trip Lever
of frame
*
4 -
¾
”
O
VERRI
D
E BU
T TON
L
OC
ATIO N
SENSO
R
LO
C
ATIO N
Elbow
Nut
TOTO U.S.A., INC. • 1155 Southern Road, Morrow, GA 30260
Tel. [phone] • Fax. [phone] • www.totousa.com
Printed in U.S.A. © TOTO LTD. 02/09 #H80174
Printed on recycled paper
Note: Min space requirement in wall is 7"
(178mm). Do not place grab bars in front of
sensor for ADA stalls.
Minimum 12” x 12” access panel or
walk-in chase is required for service and
maintainence.
RECOMMENDED INSTALLATION: