Instruction Manual Washlet Integrated Toilet G400 SN920M (MS920CEMFG) ■ Thank you for your recent purchase of the product. Please read the enclosed information to ensure the safe use of your product. ■ Be sure to read this Instruction Manual before using your product and keep it in a safe place for future reference.
What functions are available on your model? Product name, Part No. ■ Part number system Combination model number MS Top unit SN Bowl Unit CT Product name (Model) Functions Part No. Washlet Integrated Toilet G400 SN920M Ref.
Safety Precautions .................... 4 Operational Precautions .......... 11 Parts Names ............................ 12 Preparation .............................. 14 DEODORIZER, PRE-MIST,AUTO FLUSH, AUTO OPEN/CLOSE Temperature Adjustment.......... 22 Energy Saver Feature ............. 24 Wand cleaning Water Filter Drain Valve ........... 33 Water Filter (Bowl Unit) ........... 34 A mist is automatically sprayed inside the bowl unit to make it more difficult for dirt to adhere.
Safety Precautions IMPORTANT SAFEGUARDS READ ALL INSTRUCTIONS BEFORE USING Symbols and Meanings WARNING May result in death or serious injury. CAUTION May result in injury or property damage. The following symbols are used to indicate important safety instructions for the use of the product. Symbol Meaning This symbol indicates a prohibited use of the product. This symbol is used to indicate a required step in the use of this product.
Do not use the Washlet if a malfunction occurs. Always unplug the plug from the outlet. Close the water shutoff valve to stop water supply. Introduction WARNING Possible malfunctions: Water is leaking from a pipe or the top unit. The product is cracked or broken. The product makes a strange noise or emits a strange odor. The product emits smoke. The product is abnormally hot. The bowl unit is clogged. The toilet seat cushion is out of place.
Safety Precautions (Continued) WARNING Beware of irritation or burn Improper use of the toilet seat may cause irritation or burn. When sitting for a long time on the toilet seat, switch the toilet seat temperature adjustment to "OFF". When any of the following persons use a heated seat or warm air drying, someone should switch the toilet seat temperature adjustment to "OFF" and switch the drying air temperature to "Low".
Preliminary studies in females suggest that overuse of continuous spraying can increase the possibility of vaginal mucosa drying and potential reduction in desirable microbial organisms. Although these studies have not been validated, please consult your healthcare provider for concerns regarding whether these circumstances may apply to you.
Safety Precautions (Continued) CAUTION Do not pour hot water into the toilet. Doing so may result in damage to the toilet, injury or water damage. Do not flush anything other than bodily waste and toilet paper. Also, do not flush too much toilet paper. Doing so may clog the toilet, causing waste water overflow and water damage. If a water leak should occur, always close the shutoff valve.
1. Do not use while bathing. 2. Do not place or store the product where it can fall or be pulled into a tub or sink. Introduction DANGER To reduce the risk of electrocution: 3. Do not place in or drop into water or other liquid. 4. Do not reach for the product when it has fallen into water. Unplug it immediately. WARNING To reduce the risk of burns, electrocution, fire or injury to persons: 1. Close supervision is necessary when this product is used by, on, or near children or invalids. 2.
Safety Precautions (Continued) Grounding Instructions This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electrical current. The plug must be plugged into an outlet that is properly installed and grounded. DANGER - Improper use of the grounding plug can result in a risk of electric shock.
Operational Precautions ■ For prevention of damage ● Do not block the body sensor or the remote control transmitter or receiver. ● Wipe plastic areas such as the top unit and remote control with a soft cloth tightly wrung out with water. ● Do not lean against the toilet lid. < About the body sensors > Two types of body sensors are used. ● Body sensor A detects changes in heat. Detection may be difficult when the room temperature exceeds 30°C (86°F), such as in the summertime.
Parts Names Toilet lid cushion Toilet lid Product name, part no., etc.
Right side of top unit ENERGY SAVER LED FLUSH Button WATER LED Deodorizer outlet SEAT LED Deodorizing filter (Page 31) POWER LED Introduction Main display Manual flush pull cord (For flushing in case of power outage) (Page 50) Toilet seat cushions Body sensor B (Page 11) Left side of top unit Right rear of top unit Water filter drain valve (Page 33) Remote control receiver Cover Water drain plug (Page 53) 13
Preparation Using the Product for the First Time 1. Insert the battery 1 Remove the remote control from the hanger. Remote control If the remote control is secured (for anti theft) 1 Remove the screw from the remote control fixture. (View from side) Remote control Wall Hanger Hanger Screw 2 Phillips screwdriver Open the battery cover and insert two AA batteries. 2 Remove the remote control from the hanger. ■ To secure the remote control again Tighten the screw.
1 2 Insert the power plug. The wand extends and then retracts. 3. Open the shutoff valve 1 Fully open the shutoff valve. Introduction 2. Turn on the power Check that the POWER LED on the main display is lit up. Opening/closing tool (accessory) or flat-head screwdriver.
Basic Operations Press a button on the remote control; a beep sounds when the top unit receives the signal. Flushing [FULL FLUSH] Performs a full flush. Up to 10 m (33 ft) of toilet paper (single) [LIGHT FLUSH] Performs a light flush. Up to 3 m (10 ft) of toilet paper (single) Opening and closing [SEAT OPEN/CLOSE] Opens and closes the toilet seat. Stopping [STOP] Stops the operation. Cleansing [REAR] Cleanses your rear. [SOFT] Washes your rear with mild water pressure.
● Functions that operate when a button is pressed during "REAR", "SOFT" or "FRONT" cleansing. [OSCILLATING] wash your rear thoroughly. The setting changes between "ON" and "OFF" each time the button is pressed. ● [POSITION] Operation ●The wand moves back and forth to ●The wand position can be adjusted to the front or rear. ("▲": Moves to the front, "▼": Moves to the rear) [PULSATING] ●Washes with the water pressure pulsating between soft and strong.
Basic Operations About the Menu Screen This section is an overview of the settings that can be configured with the remote control. See the corresponding pages for the detailed descriptions. Remote control back side TEMPERATURE SETTING WATER Remote controller display SEAT DRYER Select keys :Select an item :Select a setting DIRECTIONAL Press [MENU] to display the menu screen. [ENTER] [MENU] [TEMP] Adjust temperatures (Page 22) 1 Press MENU The display screen changes. 1/4 1. CLEANING 2.
You can set as desired If you want to return to the previous item, press the Level 1 Level 2 CLEANING button. Level 3 1/1 AUTO FLUSH ENERGY SAVER 1/2 1. AUTO ENERGY SAVER OFF Number of items on display 1/2 1. AUTO FLUSH ON Operation WAND CLEANING MODE ON/OFF 2. AUTO FLUSH WAITING TIME 10SEC 2. TIMER SAVER OFF Menu Screen MENU 1/4 1. CLEANING AUTO FUNCTIONS 2. ENERGY SAVER 1/3 2. AUTO OPEN/CLOSE 4. OTHER SETTINGS 3.
Automatic Functions Cleaning Features, Convenience Features As you approach As you sit Removing odors inside the bowl unit As you stand up* Deodorizer stops ➝It stops after about 2 minutes DEODORIZER Starts the deodorizer A mist is sprayed inside the bowl unit to make it more difficult for dirt to adhere PRE-MIST A mist is sprayed inside the bowl unit When using the toilet seat The toilet flushes (After about 10 seconds) Flush automatically AUTO FLUSH When standing and using When using the t
As you move away "DEODORIZER" ON/OFF (Page 44) The pre-mist will not spray for about 90 seconds after you stand up from the toilet seat. Operation Note Changing settings "PRE-MIST" ON/OFF (Page 44) Auto flush is not available in the following cases. (Flush with the remote control.) ➝60 seconds after the toilet is flushed. When a person sits on the toilet seat (or when a male user stands in front of the bowl unit for "AUTO FLUSH" ON/OFF urinating) for about 6 seconds or less.
Temperature Adjustment Warm Water / Toilet Seat / Drying You can adjust the temperature levels or turn the settings to "OFF". 1 Press [TEMP]. TEMPERATURE SETTING WATER SEAT DRYER 2 Use to select the item you want to set.
3 Use to select the temperature level. TEMPERATURE SETTING Operation WATER SEAT DRYER Warm water temperature OFF Low High Press until "OFF" appears. When "OFF" is set, the WATER LED will go off. Toilet seat temperature OFF Low High Press until "OFF" appears. When "OFF" is set, the SEAT LED will go off.
Energy Saver Feature Type "AUTO ENERGY SAVER" or "TIMER ENERGY SAVER" can be selected. To save energy, the temperature of the toilet seat becomes low (or "OFF"). When the energy saver feature is "OFF", the temperature is kept at the same level. ● "AUTO ENERGY SAVER" takes about 10 days to detect time periods in which the toilet seat is never or infrequently used. When energy saver is set Type AUTO ENERGY SAVER TIMER ENERGY SAVER Situation You want the Washlet to save energy automatically.
When energy saver is in operation Toilet seat Warm water AM 0 heater heater 6 PM 8 5 9 0 Operation Example: Used infrequently from 9 pm to 6 am Set temperature*1 OFF Lit Lit (Orange) Low Low Set *2 *1 temperature temperature Low temperature*2 Example: Set from 8 am to 5 pm Set temperature*1 OFF Lit (Green) OFF Set temperature*1 OFF OFF *3 ● During auto energy saver: Same LED indication as auto energy saver (see above) ● During timer energy saver: Same LED indication as timer energy sav
Energy Saver Feature How to set Set the timer energy saver at the time you want to start it. 1 2 Press [MENU]. to select Use "ENERGY SAVER" and then press [ENTER]. MENU AUTO ENERGY SAVER 2/4 1. CLEANING 2. ENERGY SAVER 3. AUTO Remote controller display TIMER ENERGY SAVER Select keys :Select an item :Select a setting [ENTER] [MENU] TURNING OFF ENERGY SAVER Lit (Green) When energy saver is set, the ENERGY SAVER LED (green) lights up.
4 Use to select "ON/OFF" and then press [ENTER]. ENERGY SAVER 1/2 1. AUTO ENERGY SAVER OFF ENERGY SAVER 1/2 AUTO ENERGY 1. AUTO ENERGY SAVER ON SAVER ON (To return➝ 3 Use to select "TIMER SAVER". ENERGY SAVER ) Operation 3 Use to select "AUTO ENERGY SAVER". 2/2 1. AUTO ENERGY SAVER ON 2. TIMER SAVER OFF 4 Use to select "3H / 6H / 9H / OFF" and then press [ENTER]. To change the timer energy saver time ENERGY SAVER 2/2 1. AUTO ENERGY SAVER ON 2.
Maintenance Power plug (Approximately once a month) WARNING Always disconnect the power plug from the outlet before cleaning, maintenance or inspection. (see left) (Failure to do so may cause electric shock or malfunction, resulting in a breakdown.) Dry cloth Wet cloth 1 Disconnect the power plug and wipe it with a dry cloth. 2 Insert the power plug. *For safety, disconnect the power plug before cleaning or maintenance. The POWER LED lights up.
Top unit (Approximately daily) Soft cloth soaked in water 1 2 • Toilet paper • Dry cloth • Nylon scrubbing pads (May cause damage.) • Toilet brush • Neutral toilet detergent Unplug the power plug. Wipe with a soft cloth that has been soaked in water and wrung-out thoroughly. Wipe with a soft cloth soaked in diluted, neutral kitchen detergent, and then wipe with a soft cloth soaked in water.
Maintenance Gap between the Top unit and the Toilet Lid (Approximately once a month) The toilet lid can be removed for thorough cleaning. Soft cloth soaked in water 1 Unplug the power plug. 2 Remove the toilet lid. : Pull the left side outward. Toilet paper, etc. (May cause damage.) Removing and Reinstalling Hold with both hands : Disconnect the hinge from the recess and pull up. : Disconnect the right side. 3 4 C B Wipe with a soft cloth that has been soaked in water and wrung-out thoroughly.
Deodorizing filter (Approximately once a month) 1 2 Unplug the power plug. Remove the deodorizing filter. Hold the knob and pull outward. Do not pull with undue force. (May cause damage or malfunctions) Deodorizing filter When washing with water, dry off all water before mounting. Maintenance 3 Clean with a tool such as a toothbrush. Toothbrush, etc. 4 Mount the deodorizing filter. 5 Insert the power plug. Push firmly until a click sound is heard. The POWER LED lights up.
Maintenance Wand (Approximately once a month) Soft cloth soaked in water 1 Toilet paper, etc. (May cause damage.) Extend the wand. Operate with the buttons on the back side of the remote control. (1) Press [MENU]. (2) Use to select "CLEANING". Press [ENTER]. (3) to select "WAND CLEANING Use MODE ON/OFF". Press [ENTER]. The wand extends and water sprays out for cleaning. The wand automatically retracts after about 5 minutes.
Water Filter Drain Valve (Approximately once every 6 months) 1 Close the shutoff valve. The water supply stops. 4 Remove the cover and water filter drain valve. Loosen with a flat-head screwdriver and then pull. CAUTION Do not remove the water filter drain valve while the shutoff valve is open. Cover (Otherwise, water may leak out) Water filter drain valve 2 5 Also, remove any dust from inside the hole of the water filter drain valve.
Maintenance Water filter (Bowl unit) (Approximately once every 6 months) 1 Close the shutoff valve. The water supply stops. 4 Loosen the cap of the water filter to remove the water filter. Use the opening/closing tool. CAUTION Do not remove the water filter while the shutoff valve is open. (Otherwise, water may leak out) Water filter Cap Opening/ closing tool Opening/closing tool or flat-head screwdriver.
7 Install the cap of the water filter to the original position and tighten it with the opening/closing tool. Opening/ closing tool Check that there are no leaks in the shutoff valve or plumbing connections. Maintenance 8 Open the shutoff valve. Opening/closing tool or flat-head screwdriver. 9 Insert the power plug. The POWER LED lights up.
Changing Settings Setting List Setting Types AUTO FLUSH AUTO FLUSH AUTO FLUSH WAITING TIME AUTO OPEN/ CLOSE AUTO FUNCTIONS AUTO OPEN/ CLOSE AUTO CLOSE WAITING TIME AUTO OPEN WAITING TIME SEAT/LID PRE-MIST CLEANING DEODORIZER BEEP OTHER SETTINGS SETTING LOCK PERSONAL SETTING LOCK 36
Available Settings Bold: Initial settings Set whether or not to clean the bowl unit automatically Setting Ref.
Changing Settings AUTO FLUSH 1 2 3 Press [MENU]. Use to select "AUTO FUNCTIONS" and then press [ENTER]. Use to select "AUTO FLUSH" and then press [ENTER]. Remote controller display Select keys :Select an item :Select a setting [ENTER] [MENU] Items set on this display 1. AUTO FLUSH 2. AUTO FLUSH WAITING TIME 38 Set whether or not to clean the bowl unit automatically MENU 3/4 1. CLEANING AUTO FLUSH 2. ENERGY SAVER 3. AUTO FUNCTIONS 4. OTHER SETTINGS AUTO FUNCTIONS 1.
4 Use to select "AUTO FLUSH". 5 Use to select "ON/OFF" and then press [ENTER]. AUTO FLUSH 1/2 1. AUTO FLUSH ON AUTO FLUSH 1/2 AUTO FLUSH 1. AUTO FLUSH OFF OFF (To return➝ 4 Use to select "AUTO FLUSH WAITING TIME". 5 Use to select "5 SEC/10 SEC/15 SEC" and then press [ENTER]. AUTO FLUSH ) 2/2 1. AUTO FLUSH ON 2. AUTO FLUSH WAITING TIME 10 SEC AUTO FLUSH 1. AUTO FLUSH ON 2.
Changing Settings AUTO OPEN/CLOSE 1 2 3 Press [MENU]. Set whether or not to open the toilet lid automatically Use to select "AUTO FUNCTIONS" and then press [ENTER]. Use to select "AUTO OPEN/ CLOSE" and then press [ENTER]. Remote controller display Select keys :Select an item :Select a setting [ENTER] [MENU] Items set on this display 1. AUTO OPEN/CLOSE 2. AUTO CLOSE WAITING TIME 3. AUTO OPEN WAITING TIME 4. SEAT/LID 40 MENU 3/4 1. CLEANING 2. ENERGY SAVER AUTO OPEN/ CLOSE 3. AUTO FUNCTIONS 4.
4 Use to select "AUTO OPEN/ CLOSE". 5 Use to select "ON/OFF" and then press [ENTER]. AUTO OPEN/CLOSE 1/4 1. AUTO OPEN/CLOSE ON AUTO OPEN/CLOSE 1/4 AUTO FLUSH 1. AUTO OPEN/CLOSE OFF OFF (To return➝ 4 Use to select "AUTO CLOSE WAITING TIME". 5 Use to select "25SEC / 90SEC" and then press [ENTER]. *1 AUTO OPEN/CLOSE ) 2/4 1. AUTO OPEN/CLOSE ON 2. AUTO CLOSE WAITING TIME 90 SEC AUTO OPEN/CLOSE 1. AUTO OPEN/CLOSE ON 2.
Changing Settings AUTO OPEN/CLOSE 1 2 3 Press [MENU]. Use to select "AUTO FUNCTIONS" and then press [ENTER]. Use to select "AUTO OPEN/ CLOSE" and then press [ENTER]. MENU 3/4 1. CLEANING Change the time period till automatic opening (After closing manually.) AUTO OPEN WAITING TIME 2. ENERGY SAVER 3. AUTO FUNCTIONS 4. OTHER SETTINGS AUTO FUNCTIONS 2/3 1. AUTO FLUSH 2.
4 Use to select "AUTO OPEN WAITING TIME". 5 Use to select "15SEC / 30SEC / 90SEC" and then press [ENTER]. 4 Use to select "SEAT/LID". AUTO OPEN/CLOSE 3/4 2. AUTO CLOSE WAITING TIME 90 SEC 3. AUTO OPEN WAITING TIME 15 SEC AUTO OPEN/CLOSE 3/4 AUTO OPEN WAITING TIME 2. AUTO CLOSE WAITING TIME 90 SEC 3. AUTO OPEN WAITING TIME 30 SEC AUTO OPEN/CLOSE 30 SEC (To return➝ ) 4/4 3. AUTO OPEN WAITING TIME 30 SEC 4. SEAT/LID LID 5 Use to select "LID / SEAT·LID" and then press [ENTER].
Changing Settings CLEANING 1 2 3 Press [MENU]. Use to select "AUTO FUNCTIONS" and then press [ENTER]. Use to select "CLEANING" and then press [ENTER]. Remote controller display Select keys :Select an item :Select a setting [ENTER] [MENU] Items set on this display 1. PRE-MIST 2. DEODORIZER 44 MENU 3/4 1. CLEANING 2. ENERGY SAVER Set whether or not to spray mist in the bowl unit automatically PRE-MIST 3. AUTO FUNCTIONS 4. OTHER SETTINGS AUTO FUNCTIONS 3/3 1. AUTO FLUSH 2. AUTO OPEN/CLOSE 3.
4 Use to select "PRE-MIST". CLEANING 1/2 1. PRE-MIST ON 2. DEODORIZER ON 5 Use to select "ON/OFF" and then press [ENTER]. CLEANING 1/2 PRE-MIST 1. PRE-MIST OFF OFF 2. DEODORIZER ON (To return➝ 4 Use to select "DEODORIZER". CLEANING ) 2/2 1. PRE-MIST ON 2. DEODORIZER ON 5 Use to select "ON/OFF" and then press [ENTER]. CLEANING 1. PRE-MIST ON 2/2 DEODORIZER OFF 2.
Changing Settings OTHER SETTINGS 1 2 Press [MENU]. Use to select "OTHER SETTINGS" and then press [ENTER]. MENU 4/4 1. CLEANING 2. ENERGY SAVER 3. AUTO FUNCTIONS 4. OTHER SETTINGS Remote controller display Select keys :Select an item :Select a setting [ENTER] [MENU] Items set on this display 1. BEEP 2. ANTI FREEZING* 3. SETTING LOCK 4. PERSONAL SETTING LOCK *The display appears but, anti freezing feature is not available on this product.
3 Use to select "BEEP". 4 Use to select "ON/OFF" and then press [ENTER].
Changing Settings OTHER SETTINGS 1 2 Press [MENU]. Use to select "OTHER SETTINGS" and then press [ENTER]. MENU 4/4 1. CLEANING 2. ENERGY SAVER 3. AUTO FUNCTIONS 4. OTHER SETTINGS SETTING LOCK Remote controller display Set whether or not to use the personal setting lock Select keys :Select an item :Select a setting PERSONAL SETTING LOCK [ENTER] [MENU] Items set on this display 1. BEEP 2. ANTI FREEZING* 3. SETTING LOCK 4.
3 Use to select "SETTING LOCK". OTHER SETTINGS 3/4 2. ANTI FREEZING OFF 3. SETTING LOCK OFF 4 Use to select "ON/OFF" and then press [ENTER]. OTHER SETTINGS 3/4 SETTING LOCK 2. ANTI FREEZING OFF 3. SETTING LOCK ON PRESS ENTER FOR 2 SEC TO RESET 5 Check the displayed screen. Cancellation method: Press [ENTER] for 2 seconds or longer. SETTING LOCK PRESS ENTER *If you want to relock after cancellation, reconfigure the setting.
What to Do? If the water does not flow due to a power failure (when water failure hasn't occurred) ■ You can flush the toilet with the hand lever (for flushing in case of power outage). 1 Pull out the hand lever on the right side of the washlet's main body. Manual flush pull cord (For flushing in case of power outage) 2 Pull down the hand lever for about 4 seconds or longer. • Pulling the hand lever flushes the toilet. When flushing ends (after about 4 seconds), release the hand lever.
If you cannot operate with the remote control ■ Flush is also possible using the buttons on the main display. FLUSH button ■ The batteries may have worn out. Replace the batteries. ● Replacing the batteries 1 2 Unplug the power plug. 3 Open the cover and replace the AA batteries. Remove the remote control from the hanger. (Page14) (Page14) Lit Mount the remote control in the hanger. Insert the power plug. The POWER LED lights up.
What to Do? Long Periods of Disuse If the toilet is in a location you will not visit for a long time, drain the water. (The water in the tank may become contaminated and cause skin irritation or other problems.) (May cause freezing and damage to product.) How to drain the water 1 Close the shutoff valve. 2 Press [FULL FLUSH] on the remote control. CAUTION The water supply stops. Do not remove the water filter drain valve while the shutoff valve is open.
Remove the water drain plug. 4 Water comes out from around the wand (about 90 seconds) Water drain plug Reinstall the water drain plug and cover. 5 ● Putting antifreeze in the water remaining in the bowl unit will reduce its chance of freezing. (The antifreeze solution should not be flushed out. Collect it before using the toilet and dispose of it.) ■ To use the Washlet again The water needs to be resupplied. (See below) Resupplying the Water Open the shutoff valve.
Troubleshooting First, try the actions described on pages 55 to 60. If the problem persists, consult the installer, seller or the contact listed on the back cover of this manual. In the following case, unplug the plug and then plug it again. If the same symptom persists, consult with the contact referred on the back cover of this manual. CAUTION If a water leak occurs, close the shutoff valve. All LEDs are flickering Opening/closing tool or flat-head screwdriver.
Rear and Rear soft, front cleansing, wand Please check Ref. Page ● Did you sit on the toilet continuously for 2 hours or longer? (If so, operation is stopped for safety purposes.) ➞Stand up from the seat and then use again. - ● If the water supply pressure drops significantly, for example if water is used elsewhere or if there is a water failure, the function may stop for safety. ➞ Disconnect the power plug and wait about 10 seconds before inserting it again.
Troubleshooting Warm air drying Trouble Please check The dryer temperature is low ● Is the dryer temperature set to low level? Stops in the middle of use ● The feature stops automatically after 10 minutes of continuous use. ● Does the seat switch have difficulty detecting? ➞ Sit back on the toilet seat. If you get up slightly from the seat, or sit forward on the seat, the seating switch may temporarily stop detecting your presence. Ref.
Flushing Trouble Pulling the hand lever (for flushing in case of power outage) does not flush the toilet Waste material does not flush down completely Flush volume changes There is residue on the bowl unit surface Please check Ref. Page ● Pull the hand lever (for flushing in case of power outage) for 4 seconds or more to flush the toilet. 50 ● Is the shutoff valve fully open? 15 ● Is the water filter clogged? ➞Clean the filter.
Troubleshooting Toilet Seat and Toilet Lid (AUTO OPEN/CLOSE) Trouble The toilet lid does not close automatically ● Is "AUTO OPEN/CLOSE" set to "OFF"? ➞Set to "ON". ● When you do not sit on the toilet seat, or when the time spent sitting on the toilet seat or standing in front of it is 6 seconds or less, the toilet seat and toilet lid close after about 5 minutes. ● If they do not close automatically even though "AUTO OPEN/CLOSE" is set to "ON", the body sensor may be detecting incorrectly.
Toilet Seat and Toilet Lid Trouble Please check ● Is the toilet seat temperature set to "OFF" or a low level? ● Is energy saver in operation? The energy saver feature is on when the ENERGY SAVER LED is on and the POWER LED is off on the main display. When you sit on the seat, the toilet seat heater is turned on temporarily and the seat is warmed in about 15 minutes. ➞You can turn it "OFF" if the energy saver feature is "ON".
Troubleshooting Others Trouble Please check Ref. Page Water is leaking from the plumbing connections ● If any nuts in a connection are loose, firmly tighten them with a tool such as a monkey wrench. ➞If the water leak does not stop, close the shutoff valve and seek repair. - The display on the remote control goes out ● The display goes out when no button on the remote control is pressed for 5 minutes or more.
Specifications Item SN920M Rated power supply AC 120 V, 60 Hz Rated power consumption 409 W Type of water heater Tank type Power cord length 1.2 m (3.94 ft) Water protection level IPX4 Flush volume Bowl unit Full 4.8 L (1.3 gal), Light 3.4 L (0.9 gal) Water supply system Concealed tank system Flush type Cyclone flushing Bowl style Elongated Cleansing Approx. 0.27 - 0.43 L/min (Approx. 0.07 - 0.11 gal/min) Approx. 0.27 - 0.43 L/min (Approx. 0.07 - 0.
Limited Warranty 1. TOTO warrants its washlet series ("Washlet") to be free from defects in materials and workmanship during normal use when properly installed and serviced, for a period of one (1) year from date of purchase. This limited warranty is extended only to the ORIGINAL PURCHASER of the Product and is not transferable to any third party, including but not limited to any subsequent purchaser or owner of the Product.
MEMO Reference 63
TOTO U.S.A., Inc. 1155 Southern Road Morrow, GA 30260 Phone : (770) 282 8686 Warranty Registration and Inquiry For product warranty registration, TOTO U.S.A. Inc. recommends On-Line Warranty Registration. Please visit our web site http://www.totousa.com. If you have questions regarding warranty policy or coverage, please contact TOTO U.S.A. Inc., Customer Service Department, 1155 Southern Road, Morrow, GA 30260 (888) 295 - 8134 or (678) 466 - 1300 when calling from outside of U.S.A.
