Use and Care Manual

FONCTIONNEMENT DU PANNEAU DE CONTRÔLE
OPERATION INTRODUCTION FOR CONTROL PANEL
26
26
Bouton Mode3
Bouton VENTILATEUR4
MINUTERIE5
Mode SOMMEIL6
Appuyez sur ce bouton pour changer de mode de fonctionnement dans l'ordre suivant:
CLIMATISATION DÉSHUMIDIFICATION VENTILATEUR
CLIMATISATION: Lorsque l'appareil est en mode climatisation, l'indicateur lumineux
COOL est allumé. L'écran d'affichage affiche la température désirée.
La température peut être réglée entre 16 et 30 °C.
DÉSHUMIDIFICATION: Lorsque l'appareil est en mode déshumidification, l'indica-
teur DRY est allumé. L'écran d'affichage n'affichera rien.
VENTILATEUR: Lorsque l'appareil est en mode ventilateur, l'indicateur FAN est allu-
et l'appareil ne fait que pousser de l'air. L'écran d'affichage n'affichera rien.
Appuyez sur ce bouton et le ventilateur s'activera dans l'ordre suivant: Vitesse basse
Vitesse moyenne Vitesse élevée Ventilateur automatique Vitesse basse.
Appuyez sur le bouton TIMER pour démarrer le mode de réglage de minuterie. Une
fois activé, appuyez sur les boutons + et - pour ajuster la minuterie. La minuterie
augmentera ou diminuera alors de 0.5 heures en appuyant sur les boutons +/- pour
une période possible de 10 heures. Une fois la minuterie activée, l'écran d'affichage
affichera la température désirée automatiquement après 5 secondes d'inactivité. Si la
minuterie a bien été réglée, l'indicateur supérieur s'affichera . Appuyez sur le bouton
TIMER de nouveau pour annuler la minuterie.
Appuyez sur la touche SLEEP pour activer la fonction Sommeil. Si l'appareil est en
mode climatisation, lorsque la fonction sommeil est activée, la température réglée
augmentera d'un degré après une heure, et de deux degrés après deux heures. Par
la suite la température réglée demeurera de même toute la nuit. La fonction Sommeil
n'est pas disponible lorsque l'appareil est en mode ventilation, déshumidification ou
automatique. Si la fonction Sommeil est activée, l'indicateur supérieur s'affichera.
MODE button3
FAN button4
TIMER5
SLEEP6
Press this button and the mode will circulate according to below sequence:
COOL DRY FAN
COOL: Under this mode, the cooling mode indicator lights up. The screen dis-
plays set temperature. Temperature setting range is 61°F (16°C) - 86°F (30°C).
DRY: Under this mode, drying mode indicator lights up; the screen does not
display.
FAN: Under this mode, the air conditioner fan is activated, only blowing air. The
fan indicator lights up. The screen does not display.
Press this button and the fan speed will circulate as "low speed medium speed
high speed auto fan low speed".
Press timer button to enter into timer setting mode. Under this mode, press "+" or "-"
button to adjust the timer setting. Timer setting will increase or decrease 0.5 hour up
to a maximum of 10 hours.
After timer setting is finished, the unit will automatically display set temperature if the
unit is not operating for 5 seconds. If timer function has been properly set, the upper
indicator will display. Under timer mode, press timer button again to cancel timer
mode.
Press sleep button to enter into sleep mode. If the controller operates in cooling
mode, after sleep mode is activated, preset temperature will increase by 1 degree
within 1 hour, and by 2 degrees within 2 hours; the unit will maintain this
temperature. The Sleep function is not available
under fan, drying or auto mode. If the sleep function is activated, the upper indicator
will display.