Operation Manual

45
Operations
44
[Auto input Search]
[On]: Automatically searches the signals that
can be projected, and switches input
from the connected device that outputs
the signals each time the INPUT button
is pressed. The input from the connected
device that outputs no signals is skipped.
[Off]: Displays the Switch input menu.
Toggle with
buttons and press
button (The input without signals can be
selected.)
[Power on]
Note that if [Power on] is set to [Auto], then if the main power switch is ON when
power is restored after a power outage, the projector will come on.
[Lamp power]
When [Lamp power] is set to [Low], the screen becomes a little darker, but the
cooling fan noise gets quieter.
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to
use the projector, for example, at high altitude (over 1,500 meters above sea level).
[Remote control code]
Sets a remote control code from 4 types. You can set each code respectively for up
to 4 projectors. The factory setting is [1].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
•You cannot operate the remote control if the codes of the projector and the
remote control do not match.
Remote control code setting for remote control
Remove the battery cover and set the same remote control code switch as the
projector.
p.16
(Use a screwdriver with thin tip to set.)
[Key lock]
Protect from operating errors by locking on the control panel buttons of the
projector.
(The remote control operations are available.)
Control panel operations are locked after the setting is done.
•To release the key lock, press the control panel’s RETURN button for 10 seconds.
The key lock is released with a beep sound.
Computer (1) (digital)
Y/P
B/PR (1) (digital)
Computer (1) (analog)
Y/P
B/PR (1) (analog)
Computer (2)
Y/P
B/PR(2)
Computer (3)
Y/P
B/PR(3)
Video
S-video
Switch input
/ shows whether signal is
input or not.
Switch input menu
Using the menus (Continued)
■ The default setting menu
This menu shows placement status and other settings.
Sets projection mode in accordance with Placement Style.
When projecting on a non-screen surface, select a color in accordance
with the projecting surface.
Press . Switch with and .
Off/Green/Black/Brown/Blue/Beige
Set the time to wait for the power to be turned off after signal input
stops or the last operation.
Press . Switch with and .
Off (not turned off)/1 min./5 min./10 min./30 min./60 min.
Set whether the input with signals is only selected or not.
Sets whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto). Manual Auto
Sets the lamp power.
Sets the cooling fan speed.
When two or more projectors are used and controlled by the remote
control respectively, this menu sets the code for the projector and the
remote control.
[ :Enter setting mode] [ : Select item] [ : Select
from 1, 2, 3, 4] [ :Confirm] [ :Select OK to end]
Press [Cancel] to return.
Lock the control panel buttons.
[ :Enter setting mode] [ : Select item] [ : Select
On/Off] [ :Confirm] [ :Select OK to end]
Press [Cancel] to return.
Press .
Resets all adjustments and settings to their factory settings.
Password function
When [Password] is [On], the Password Setting screen is displayed.
Description
Item
Projection
mode
Blackboard
mode
No signal
power off
Auto input
search
Power on
Lamp power
Fan mode
Remote control
code
Key lock
Reset all
Password
(Rear mounted
from ceiling)
(Standard)
(Rear)
(Mounted
from ceiling)
On Off
Standard High
Yes No
On Off
Low Standard
p.22
p.36
Detailed description
[Blackboard mode]
Projects the image in colors more like projecting on a screen.
Precaution
The projected image may differ depending on the type, color, and material of the
blackboard and wall even if the selected color is the same as the projected screen.