Satellite® U400 Series User’s Guide If you need assistance: ❖ Toshiba’s Support Web site pcsupport.toshiba.com ❖ Toshiba Customer Support Center Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see “If Something Goes Wrong” on page 164 in this guide.
Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Model: Satellite® U400 Series Recordable and/or ReWritable Drive(s) and Associated Software Warranty The computer system you purchased may include Recordable and/or ReWritable optical media drive(s) and associated software, among the most advanced data storage technologies available.
Critical Applications The computer you have purchased is not designed for any “critical applications.” “Critical applications” means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ❖ This device may not cause harmful interference. ❖ This device must accept any interference received, including interference that may cause undesired operation. Contact either: ❖ Toshiba’s Support Web site at pcsupport.toshiba.com.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. Telephone Company Procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations or procedures.
Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. Instructions for IC CS-03 Certified Equipment 1 NOTICE: The Industry Canada label identifies certified equipment.
Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖ The IEEE 802.11 Standard on Wireless LANs (Revision A/B/G), as defined and approved by the Institute of Electrical and Electronics Engineers. ❖ The Wireless Fidelity (Wi-Fi®) certification as defined by the Wi-Fi Alliance.
In some situations or environments, the use of Wireless LAN may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include: ❖ Using the Wireless LAN equipment on board airplanes, or ❖ In any other environment where the risk of interference to other devices or services is perceived or identified as harmful.
The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
The European Union WEEE (Waste from Electrical and Electronic Equipment) Directive Information The European Union WEEE (Waste from Electrical and Electronic Equipment) Directive is intended to protect the quality of the environment and human health through the responsible use of natural resources and the adoption of waste management strategies that focus on recycling and reuse.
However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance.
2. Indication The indication shown below appears on this equipment. (1) (2) (3) 2.4DSOF4 (4) 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 DS: This equipment uses DS-SS modulation. OF: This equipment uses OFDM modulation. 3 The interference range of this equipment is less than 40m. 4 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems. 3.
Radio Approvals for Wireless Devices NOTE The following information is dependent on what type of wireless device is in your computer. Not all devices are available on all models. Approved Countries/Regions for use for the Atheros AR5BXB72 2.4 + 5GHz 11n minicard This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. NOTE This device works on passive scan only.
Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ Belgique: Deutschland: France: Italia: Nederland: For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m. For registration and license please contact IBPT/BIPT.
Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries 5150-5250 MHz 5250-5350 MHz European Community Countries Channels: 36, 40, 44, 48 Austria Belgium, France, Switzerland/Liechtenstein Denmark, Finland, Germany, Greece, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Sweden, UK Iceland, Spain 5470-5725 MHz Channels: 52, 56, 60, Channels: 100, 104, 108, 112, 64 116, 120, 124, 128, 132, 136, 140 Indoor Only O O Indoor Only x O Indoor/Outdoor x x O O O O
Approved Countries/Regions for use for the Atheros AR5BXB63 11g minicard This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. NOTE This device works on passive scan only. A peer-to-peer mode is not available in 802.11a and Turbo Mode.
Approved Countries/Regions for the Realtek® RTL8187B This equipment is approved to the radio standard by the countries/regions in the following table.
Approved Countries/Regions for use for the Intel® PRO/Wireless 3945ABG Network Connection This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. NOTE An adhoc mode is available in Ch1-Ch11(802.11b/g), An Infrastructure mode is available in Ch1-Ch11 (802.11b/g) Ch36,40,44,48,52,56,60,64,149,153,157,161,165 (802.
Approved Countries/Regions for the Intel® Wireless Wi-Fi® Link 4965AGN This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. NOTE An adhoc mode is available in Ch1-Ch11(802.11b/g), An Infrastructure mode is available in Ch1-Ch11 (802.11b/g) Ch36,40,44,48,52,56,60,64,149,153,157,161,165 (802.11a).
Bluetooth® Wireless Technology Interoperability Bluetooth® Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ❖ ❖ Bluetooth Specification as defined and approved by The Bluetooth Special Interest Group. Logo certification with Bluetooth wireless technology as defined by The Bluetooth Special Interest Group.
Approved Countries/Regions for use (Bluetooth® wireless technology) Bluetooth® Card from Toshiba equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include: ❖ Using the equipment with Bluetooth wireless technology on board airplanes, or ❖ In any other environment where the risk of interference to other devices or services is perceived or identified as harmful.
Taiwan Article 14 Article 17 Unless approved, for any model accredited low power radio frequency electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design. Any use of low power radio frequency electric machinery shall not affect aviation safety and interfere with legal communications. In the event interference is caused, the use of such electric machinery shall be immediately discontinued.
2. Indication The indication shown below appears on this equipment. (1) (2) (3) 2.4FH1 (4) 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 FH: This equipment uses FH-SS modulation. 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3.
Optical Drive Safety Instructions This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT. To use this model properly, read the user’s guide carefully and keep it for your future reference. Never attempt to disassemble, adjust or repair an optical drive. You could damage the drive. You would also be exposed to laser light or other safety hazards, resulting in serious injury. Always contact an authorized Toshiba service provider, if any repair or adjustment is required.
Export Administration Regulation This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and may be subject to the approval of the U.S. Department of Commerce prior to export. Any export, directly or indirectly, in contravention of the U.S. Export Administration Regulations is prohibited. Notice The information contained in this manual, including but not limited to any product specifications, is subject to change without notice.
Trademarks Satellite and ConfigFree are registered trademarks of Toshiba America Information Systems, Inc. and/or Toshiba Corporation. Microsoft, Outlook, Windows, and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. DirectX, Active Desktop, DirectShow, and Windows Media are registered trademarks of Microsoft Corporation. Wi-Fi is a registered trademark of the Wi-Fi Alliance.
Contents Introduction................................................................................ 35 This guide ...............................................................37 Safety icons ............................................................38 Other icons used...............................................38 Other documentation ..............................................39 Service options .......................................................39 Chapter 1: Getting Started..................
Contents 29 Using the computer for the first time ......................49 Opening the display panel .................................49 Your computer’s features and specifications ....50 Turning on the power .......................................50 Adding memory (optional) ......................................51 Installing a memory module .............................52 Removing a memory module............................57 Checking total memory .....................................
Contents Caring for your computer........................................84 Cleaning the computer ......................................84 Moving the computer........................................84 Using a computer lock ......................................85 Chapter 2: Learning the Basics................................................. 86 Computing tips .......................................................86 Using the keyboard .................................................
Contents 31 Chapter 3: Mobile Computing.................................................103 Toshiba’s energy-saver design..............................103 Running the computer on battery power ..............103 Battery Notice .................................................104 Power management ........................................105 Using additional batteries ...............................105 Charging batteries.................................................105 Charging the main battery............
Contents Surfing the Internet.........................................127 Internet features..............................................128 Uploading to, and downloading files from, the Internet .....................................128 Exploring audio features .......................................129 Recording sounds...........................................129 Using external speakers or headphones..........129 FM tuner ...............................................................130 Web Camera .
Contents 33 TOSHIBA Accessibility ..........................................156 Fingerprint Authentication Utility...........................157 Fingerprint utility limitations ...........................157 Using the Fingerprint Authentication Utility.....157 Fingerprint Logon ...........................................158 Care and maintenance of your fingerprint reader .......................................................158 Fingerprint reader limitations ..........................159 ConfigFree® ....
Contents Data and system configuration backup in the Windows® operating system...............188 If you need further assistance...............................193 Before you contact Toshiba ............................193 Contacting Toshiba .........................................193 Other Toshiba Internet Web sites..........................194 Toshiba’s worldwide offices..................................194 Appendix A: Hot Keys/TOSHIBA Cards..................................196 Hot Key Cards ........
Introduction Welcome to the world of powerful, portable, multimedia computing. With your Toshiba computer, your work and entertainment can accompany you wherever you go. Your Computer model may be ENERGY STAR® compliant. If the model you purchased is compliant, it is labeled with the ENERGY STAR® logo on the computer and the following information applies.
Introduction According to the EPA, a computer meeting the new ENERGY STAR® specifications will use between 20% and 50% less energy depending on how it is used. If all U.S. household and businesses replaced old computers with new ENERGY STAR® qualified models, we would save more than $1.8 billion in energy costs over the next five years and avoid greenhouse gas emissions equivalent to more than 2.7 million cars.
Introduction This guide NOTE 37 The product specifications and configuration information are designed for a product Series. Your particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specifications on your particular model, please visit Toshiba’s Web site at pcsupport.toshiba.com.
Introduction Safety icons Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Introduction Other documentation 39 Other documentation Your computer comes with the following documentation: ❖ An electronic version of the user’s guide (this document) ❖ It may also contain guides for other programs that may come with your system. For accessory information, visit Toshiba’s Web site at accessories.toshiba.com. Service options Toshiba offers a full line of optional service programs to complement its standard limited warranty.
Chapter 1 Getting Started This chapter provides tips for using your computer effectively, summarizes how to connect components, and explains what to do the first time you use your computer. The “Instruction Manual for Safety and Comfort,” that is shipped with your computer, contains important safety information.
Getting Started Selecting a place to work 41 To keep your computer in prime operating condition, protect your work area from: ❖ Dust, moisture, and direct sunlight. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ❖ Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters. ❖ Extreme heat, cold, or humidity.
Getting Started Selecting a place to work ❖ ❖ Avoid prolonged physical contact with the underside or surface of the computer. Computer base and palm rest can become hot! Avoid prolonged contact to prevent heat injury to skin. Read the “Avoid extended contact between computer base/palm rest and skin” section in the “Instruction Manual for Safety and Comfort” that is shipped with your computer. Never place a heavy object on the computer and be careful not to drop a heavy object onto the computer.
Getting Started Setting up your computer 43 Important information on your computer’s cooling fan Your computer may have a CPU cooling fan that cools the CPU by drawing outside air into the computer. Always make sure your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Sleep mode).
Getting Started Setting up your computer NOTE Please handle your computer carefully to avoid scratching or damaging the surface. Setting up your software When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely. NOTE The names of windows displayed, and the order in which windows appear, may vary according to your software setup choices.
Getting Started Registering your computer with Toshiba 45 Registering your computer with Toshiba Product registration is strongly recommended, and allows Toshiba to send you periodic updates, announcements, and special offers applicable to your product. Product registration can be completed by either visiting the Toshiba Web site at http://www.register.toshiba.com, or by double-clicking the Toshiba Resources icon on your desktop and then double-clicking Toshiba Registration.
Getting Started Connecting to a power source Connecting to a power source Your computer requires power to operate. Use the power cord/cable and AC adaptor to connect the computer to a live electrical outlet, or to charge the computer’s battery. Never pull on a power cord/cable to remove a plug from a socket. Always grasp the plug directly. Failure to follow this instruction may damage the cord/cable, and/or result in a fire or electric shock, possibly resulting in serious injury.
Getting Started Connecting to a power source 47 To connect AC power to the computer: 1 Connect the power cord/cable to the AC adaptor. (Sample Illustration) Connecting the power cord/cable to the AC adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. _ + 2 Plug the AC adaptor cord into the DC-IN on the back of the computer.
Getting Started Charging the main battery The computer’s main battery light gives you an indication of the main battery’s current charge: NOTE ❖ Glows amber while the main battery is being charged (AC adaptor connected) ❖ Glows white when the main battery is fully charged ❖ Is unlit when the main battery has discharged, the battery is not charging, or the AC adaptor is not plugged into the computer or AC outlet ❖ Flashes amber when the main battery charge is low and it is time to recharge the
Getting Started Using the computer for the first time NOTE 49 Battery life and charge time may vary depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel 1 Facing the front of the computer, locate the center of the display panel. 2 Gently raise the panel. 3 Adjust the display to a comfortable viewing angle.
Getting Started Using the computer for the first time Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using highprecision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology. Over a period of time, and depending on the usage of the computer, the brightness of the screen will deteriorate.
Getting Started Adding memory (optional) 3 51 Press and release the power button. The on/off light glows white. (Sample Illustration) Turning on the power The preinstalled operating system will load automatically. When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely. Adding memory (optional) HINT: To purchase additional memory modules, see the accessories information packaged with your system or visit accessories.toshiba.com.
Getting Started Adding memory (optional) Installing a memory module Memory modules can be installed in the memory module slots on the base of the computer. You will need a small Phillips screwdriver for this procedure. If the computer has been running recently, the memory module may be hot. The surrounding area may also be hot. Allow the module to cool to room temperature before replacing it. Avoid touching the cover, the module, and the surrounding area before they have cooled.
Getting Started Adding memory (optional) 53 If the computer is on, begin at step 1; otherwise, skip to step 3. 1 Click Start, and then click the arrow next to the lock button in the lower-right corner of the Start menu. The Shut Down menu appears. Start Arrow Shut Down Menu (Sample Image) Shut Down menu 2 Click Shut Down. The operating system turns off the computer. 3 Unplug and remove any cables connected to the computer, including the AC adaptor. 4 Remove the main battery.
Getting Started Adding memory (optional) 6 Using a small Phillips screwdriver, loosen the captive screws that secure the memory module slot cover. Back of computer (Sample Illustration) Removing the memory module slot cover 7 Remove the memory module slot cover. 8 Place the screws and the cover in a safe place so that you can retrieve them later. Static electricity can damage the memory module.
Getting Started Adding memory (optional) 55 NOTE If your system has the memory modules stacked on top of one another, you must remove the top module first before removing/installing the bottom module. NOTE For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. 11 Pick up the memory module by its sides, avoiding any contact with its connector.
Getting Started Adding memory (optional) 13 Once the module’s connector is fully inserted into the socket, press downward on the top edge of the module to seat the module into the latches at the sides of the socket. These latches should “snap” into place securely with the corresponding cutouts in the side of the module. If the latches and cutouts do not line up correctly, repeat steps 12-13.
Getting Started Adding memory (optional) 57 15 Re-insert the main battery. For more information on inserting the main battery, see “Inserting a charged battery” on page 115. 16 Turn the computer right side up. 17 Reconnect the cables. 18 Restart the computer. TECHNICAL NOTE: You must have at least one memory module installed for the computer to work. You can now continue setting up the computer.
Getting Started Adding memory (optional) NOTE The following screen may appear when you turn on the power: If “Start Windows® Normally” is highlighted, then press Enter. If one of the Safe Mode options is highlighted, it is best to press Enter to go into Safe Mode, then shut down and restart the system, at which time Windows® should boot back up normally. When Safe Mode is suggested, this could be a sign that you may need to scan your internal storage drive for errors or defragment the drive.
Getting Started Adding memory (optional) 59 4 Replace the memory module slot cover and secure it using the screws. 5 Re-insert the main battery. For more information on inserting the main battery, see “Inserting a charged battery” on page 115. 6 Turn the computer right side up. 7 Reconnect the cables. 8 Restart the computer. TECHNICAL NOTE: You must have at least one memory module installed for the computer to work.
Getting Started Hard Drive Recovery Utilities Hard Drive Recovery Utilities (Available on certain models) Your computer has been configured with a hard disk partition to allow you to recover your hard disk drive or reinstall selected applications and software features or utilities. NOTE It is strongly recommended that you create recovery DVDs before using your system. For more information on creating Recovery media see “Creating Recovery DVDs” on page 60.
Getting Started Hard Drive Recovery Utilities 61 To create recovery DVDs: 1 Click Start, All Programs, Toshiba, Recovery, and then Recovery Disc Creator. 2 Select DVD (to create Recovery media on DVDs). 3 Select the items you want to copy by clicking the check box next to the item’s Name—recovery files, applications (original bundled drivers and applications), or both the recovery files and applications. 4 Click Create. 5 Insert the first blank DVD into your writable optical drive when prompted.
Getting Started Hard Drive Recovery Utilities Hard Disk Drive Recovery using the recovery partition You have the options of recovering your system using the Hard Drive Recovery partition to the factory-set default, or recovering just your C: drive and leaving other partitions (for example, a D: drive) intact, or changing the size of your C: drive and then recovering it. To recover your hard disk drive using the utilities stored on your computer’s HDD: 1 Make sure the computer is turned off.
Getting Started Hard Drive Recovery Utilities 63 Recovering the original factory image (recommended recovery method) Recovering a hard disk drive to its out of box state deletes all partitions on the hard disk drive and your information will be lost. Be sure to save your work to external media first. 1 On the Toshiba Recovery Wizard screen, select Recovery of Factory Default Software, and then click Next. The Recovery of Factory Default Software screen appears.
Getting Started Hard Drive Recovery Utilities Erasing the hard disk The Recovery Wizard allows you to delete all data and partitions from the hard disk. To delete the data and partitions from your hard disk: 1 On the Toshiba Recovery Wizard screen, select Erase the hard disk, and then click Next. 2 The next screen lists the two methods you can choose: ❖ Delete all data and partitions from the hard disk—This option deletes all of the data on the hard disk without overwriting the HDD.
Getting Started Hard Drive Recovery Utilities 65 Recovering the C: partition of the HDD without changing the current partition size Recovering the C: drive to its factory default setting reformats your drive and your information on the recovered drive will be lost. Be sure to save your work to external media first. If you have created other partitions (for example, a D: drive) those partitions and any information on them will not be affected and will remain intact.
Getting Started Hard Drive Recovery Utilities 4 Click Next to begin the restoration. Once complete, a message displays that the HDD has been recovered. 5 Press any key on your keyboard to restart the computer. Hard Disk Drive Recovery using the Recovery media If you need to recover your computer to its default factory state, you can rebuild the system using your Hard Drive Recovery Utilities.
Getting Started Using the TouchPad™ 67 3 Select Manage. 4 Click Disk Management. 5 Highlight the hard disk drive in the Volume list to display its status in the lower portion of the screen. Installing drivers and applications (Available on certain models) The Toshiba Application Installer (available on certain models) allows you to reinstall the drivers and applications that were originally bundled with your computer.
Getting Started Using external display devices Scrolling with the TouchPad™ There are two active regions on the TouchPad™ that allow you to scroll as you would with any wheel device on a mouse or trackball. To scroll vertically, run your finger up or down along the right edge of the TouchPad. To scroll horizontally, run your finger along the bottom edge of the TouchPad. This feature can be disabled or changed in the Mouse Properties dialog box.
Getting Started Using external display devices 4 69 Turn on the external device. Your computer will automatically detect the external display device and activate a screen with display options. 5 Select the settings you desire and click Apply. 6 Click OK. NOTE In the future you can change the display settings by pressing Fn+F5, or by configuring the display properties settings.
Getting Started Using external display devices The quickest way to change the display output settings is to use the display hot key (Fn + F5): 1 While holding down Fn, press F5 repeatedly until the setting you want takes effect. Briefly pause each time you press the F5 key to allow time for the display to change.
Getting Started Using an external keyboard 71 Adjusting the quality of the external display To obtain the best picture quality from your television (or other video display device), you may need to adjust the video settings. See the video device documentation for additional configuration steps. Using an external keyboard If you prefer to use a full-size keyboard, you can attach one to your computer. The computer’s USB ports support most USBcompatible keyboards.
Getting Started Connecting a printer To connect a printer to your computer: 1 Connect the printer cable to the printer and then connect the other end to one of the computer’s USB ports. 2 Plug the printer’s power cable into a live AC outlet. Setting up a printer NOTE Some printers require a specific installation process. Refer to your printer installation guide for instructions before completing the following procedure.
Getting Started Connecting an optional external diskette drive 73 Connecting an optional external diskette drive Some operations, such as creating a password service diskette, require a diskette drive designed for use with 3.5-inch diskettes. (Sample Illustration) Optional external USB diskette drive To connect an optional external USB diskette drive, connect the cable to one of the computer’s USB ports.
Getting Started Turning off the computer Options for turning off the computer Depending on the operating system installed, you have more than one option available for turning off the computer: Shut Down, Hibernate, and Sleep. Each option has its advantages. ❖ Use the Shut Down or Hibernate command if you will not be using the computer for several days or if you must turn off your computer. You must turn off your computer in order to upgrade your computer’s internal hardware (such as memory).
Getting Started Turning off the computer 75 For information on how to use and configure Hibernation mode see “Using and configuring Hibernation mode” on page 78. Sleep mode The Sleep command places the computer into a power-saving mode. Sleep saves the current state of the computer to memory so that, when you restart the computer, you can continue working from where you left off.
Getting Started Turning off the computer Using the Shut Down command The Shut down command completely shuts down the computer without saving your work or the current state of the computer. This command closes all open programs, shuts down the operating system, and then turns off your computer. Use the following steps to turn off your computer using the Shut Down command: 1 Click Start, and then click the arrow next to the Lock button in the lower-right part of the Start menu.
Getting Started Turning off the computer 3 77 Click Change advanced power settings. The Advanced settings tab of the Power Options window appears. (Sample Image) Advanced settings tab of Power Options screen 4 Click Power buttons and lid to display the actions that you can configure. 5 Select the options you want from the drop-down lists. NOTE These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power.
Getting Started Turning off the computer 6 Click Apply. 7 Click OK. Once the computer is configured, you can turn it off by either pressing the power button or closing the display panel, depending on the options set. Restarting your computer To start the computer up again, press the power button until the on/off light glows white. If you turn off the computer by closing the display panel, you can start it again by opening the display panel.
Getting Started Turning off the computer 79 Configuring Hibernation mode options You can place the computer into Hibernation mode by either pressing the power button or closing the display panel. You can also specify an amount of time after which the computer automatically goes into Hibernation mode. To use any of these methods, you first need to enable them using the Power Options feature. 1 Click Start, Control Panel, System and Maintenance, and then Power Options. The Power Options window appears.
Getting Started Turning off the computer 4 Click Power buttons and lid to display the actions that you can configure. 5 Select Hibernate for the options you want. NOTE These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power. ❖ Lid close action Set this option to Hibernate if you want the computer to go into Hibernation mode when you close the display panel.
Getting Started Turning off the computer 81 Using and configuring Sleep mode To turn off the computer using the Sleep command: 1 Click Start, and then click the arrow next to the Lock button in the lower-right part of the Start menu. The Shut Down menu appears. Start Arrow Shut Down Menu (Sample Image) Shut Down menu 2 Click Sleep. The computer saves the status of all open programs and files to the memory, turns off the display, and enters into a low-power mode.
Getting Started Turning off the computer 2 Click Change plan settings under the power plan to be customized. The Edit Plan Settings window appears. (Sample Image) Edit Plan Settings screen 3 4 To change the amount of time after which the computer enters Sleep mode: ❖ Under Put the computer to sleep, select the desired amount of time in both the On battery and Plugged in categories. ❖ To disable the computer from automatically entering Sleep mode, select Never.
Getting Started Turning off the computer 83 5 Click Power buttons and lid to display the actions that you can configure. 6 Select Sleep for the options you want. NOTE These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power. ❖ Lid close action Set this option to Sleep if you want the computer to go into Sleep mode when you close the display panel.
Getting Started Customizing your computer’s settings Customizing your computer’s settings There are several ways in which you can customize your computer to suit your particular requirements. Refer to your operating system documentation or Help and Support for details. You may also wish to customize your power usage settings. For more information, see “Power Plans” on page 111. There are additional custom settings you can choose. See “Utilities” on page 135.
Getting Started Caring for your computer 85 Using a computer lock You may want to secure your computer to a heavy object such as your desk. The easiest way to do this is to purchase an optional computer lock cable. For more information on purchasing a cable lock, visit accessories.toshiba.com. (Sample Illustration) Computer lock cable To secure the computer: 1 Wrap the cable through or around some part of a heavy object. Make sure there is no way for a potential thief to slip the cable off the object.
Chapter 2 Learning the Basics This chapter gives some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work stays in the computer’s temporary memory until you save it to the internal storage drive. If the network you are using goes down and you must restart your computer to reconnect, or your battery runs out of charge while you are working, you will lose all work since you last saved.
Learning the Basics Computing tips ❖ 87 Back up your files to disks (or other removable media) on a regular basis. Label the backup copies clearly and store them in a safe place. It is easy to put off backing up because it takes time. However, if your internal storage drive suddenly fails, you will lose all the data on it unless you have a separate backup copy. For more information, see “Data and system configuration backup in the Windows® operating system” on page 188.
Learning the Basics Using the keyboard Using the keyboard Your computer’s keyboard contains character keys, control keys, function keys, and special Windows® keys, providing all the functionality of a full-size keyboard. (Sample Illustration) Keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The space bar creates a space character instead of just passing over an area of the page.
Learning the Basics Using the keyboard 89 Ctrl, Fn, and Alt keys (Sample Illustration) Ctrl, Fn, and Alt keys The Ctrl, Fn, and Alt keys do different things depending on the program you are using. For more information, see your program documentation. Function keys The function keys (not to be confused with the Fn key) are the 12 keys at the top of the keyboard. (Sample Illustration) Function keys F1 through F12 are called function keys because they execute programmed functions when pressed.
Learning the Basics Using the keyboard Overlay keys The keys with gray numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the 10-key keypad on a desktop computer’s keyboard. (Sample Illustration) Numeric and cursor control overlay Using the overlay to type numeric data The keys with the numbers on their right front are the numeric overlay keys.
Learning the Basics Starting a program 91 Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. To find the file, use the Start menu or Windows® Explorer. If you prefer to open the program first, you have four options.
Learning the Basics Starting a program Starting a program from Windows® Explorer If a program is not listed in the All Programs menu, you can start it from Windows® Explorer. Windows® Explorer gives you a view of your computer’s contents as a hierarchy or “tree.” You can easily see the contents of each drive and folder on your computer. To use this method, you should know the file name and location of the program’s executable file (this file ends with .exe).
Learning the Basics Saving your work Starting a program using the Start Search field This example uses the Start menu’s Start Search field to start WordPad: 1 Click Start to display the Start menu. The Start Search field appears at the bottom of the Start menu. Start Search field Arrow (Sample Image) Start Search field in Start menu 2 Start typing the program’s name (wordpad) in the Start Search field. As you type, all matching files and programs are displayed in the Start menu.
Learning the Basics Saving your work Saving files 1 In your Windows®-based application, click File, and then Save. 2 Click Browse folders. If you are working with a document that already has a file name, this is all you need to do. If you created a new document, your program displays a Save As dialog box. Use this dialog box to specify where to store the document and to give it a file name. (Sample Image) Save As dialog box 3 Choose the drive and folder where you want your file to be stored.
Learning the Basics Printing your work 95 Using a file extension Most programs assign an extension to the file name that identifies the file as being created in the program with a particular format. For example, Microsoft® Word saves files with a .doc extension. Any file name with an extension of “.doc” is assumed to be a Microsoft® Word file. Creating your own extension is usually unwise, since the program is unlikely to recognize a strange extension and may refuse to handle your file correctly.
Learning the Basics Backing up your work 3 Specify the print parameters. For example, the range of pages and number of copies to print. 4 Click Print. Backing up your work Back up all the files you create in case something happens to your computer. You can back up your files to different types of media such as CDs, DVDs, diskettes, or to a network, if available. To back up several files at one time, use the Microsoft® Windows® backup program preinstalled on the computer’s internal storage drive.
Learning the Basics Using the optical drive 97 TECHNICAL NOTE: Your optical drive is set to play region 1 (North America) DVD-ROMs. If you play a DVD disc from another region, the drive will automatically change to play in the format of the other region. The drive will allow you to change regions four times. On the fourth change, the region will be “locked in.” That is, the drive will only play DVDs from that last region.
Learning the Basics Using the optical drive Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. Media control buttons The media control buttons located on the system control panel above the keyboard let you mute the sound and play audio CDs or DVD movies when the computer is on.
Learning the Basics Using the optical drive 4 99 Grasp the tray and pull it fully open. (Sample Illustration) Drive tray fully extended 5 Hold the disc by its edges and check that it is free of dust. If the disc is dusty, clean it as described in “Caring for optical discs” on page 102. 6 Place the disc carefully in the disc tray, label side up. (Sample Illustration) Positioning the disc in the drive 7 Gently press the disc onto the center spindle until it clicks into place.
Learning the Basics Using the optical drive 8 Make sure the disc is completely on the spindle and is lying flat on the tray. If you insert the disc incorrectly, it may jam the drive. If this happens, contact Toshiba support for assistance. 9 Push the disc tray in by pressing gently on the center of the tray until it clicks into place. You are ready to use the disc. Playing an audio CD Insert an audio CD and close the disc tray. If the computer is turned on, the default player opens.
Learning the Basics Using the optical drive 101 Recording optical media Depending on the configuration, your computer may come with an optical drive that allows you to: ❖ Play pre-recorded and recorded optical media. ❖ Read/write data and multi-media files to recordable optical media. For more information regarding supported optical media formats please refer to your computer’s detailed specifications at pcsupport.toshiba.com.
Learning the Basics Toshiba’s online resources Removing a disc with the computer off To remove a disc with the computer turned off: 1 Insert a slender object, such as a straightened paper clip, into the manual eject hole. The disc tray slides partially out of the drive (about 1 inch). Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. 2 Pull the tray out until it is fully open, remove the disc, and place it in its protective cover.
Chapter 3 Mobile Computing This chapter covers all aspects of using your computer while traveling. Toshiba’s energy-saver design Your computer enters a low-power suspension mode when it is not being used, thereby conserving energy and saving money in the process. It has a number of other features that enhance its energy efficiency. Many of these energy-saving features have been preset by Toshiba.
Mobile Computing Running the computer on battery power Battery Notice Battery life may vary considerably from specifications depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage.
Mobile Computing Charging batteries 105 Power management Your computer ships with the power management options preset to a configuration that will provide the most stable operating environment and optimum system performance for both AC power and battery modes. Changes to these settings may result in system performance or stability issues. Users who are not completely familiar with the power management component of the system should use the preset configuration.
Mobile Computing Charging batteries Charging the main battery To charge the main battery while it is in your computer, plug the computer into a live electrical outlet. The battery charges whether the computer is on or off. TECHNICAL NOTE: The recharging of the battery cannot occur when your computer is using all of the power provided by the AC adaptor to run applications, features, and devices.
Mobile Computing Monitoring main battery power 107 If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date, or stop working. To recharge the RTC battery, plug the computer into a live electrical outlet and leave the computer powered on for 24 hours. NOTE It is seldom necessary to charge the RTC battery because it charges while the computer is on.
Mobile Computing Monitoring main battery power HINT: Be careful not to confuse the battery light ( light ( ). ) with the on/off When the on/off light flashes amber, it indicates that the system is suspended (using the Windows® operating system Sleep command).
Mobile Computing Monitoring main battery power 109 Highlight the power icon in the Notification Area. A pop-up message displays the remaining battery power as a percentage. With repeated discharges and recharges, the battery’s capacity gradually decreases. A frequently used older battery does not power the computer for as long as a new battery, even when both are fully charged. TECHNICAL NOTE: The computer drains the battery faster at low temperatures.
Mobile Computing Monitoring main battery power To change the default notification settings: 1 Click Start, Control Panel, Mobile PC, and then Power Options. The Power Options window appears. 2 Click Change plan settings under the power plan to be customized. The Edit Plan Settings window appears. 3 Click Change advanced power settings. The Advanced settings tab of the Power Options window appears.
Mobile Computing Monitoring main battery power 111 There are various ways in which you can conserve power and extend the operating time of your battery: ❖ Enable Sleep or Hibernation, which saves power when you turn off the computer and turn it back on again ❖ Use the Windows® power-saving option plans These power-saving options control the way in which the computer is configured. By using them, you can increase the length of time you can use the computer before you need to recharge the battery.
Mobile Computing Monitoring main battery power NOTE 4 To edit a plan or to edit advanced settings, continue to the following steps. Click Change Plan Settings to choose the plan you want to edit. This screen allows you to change basic settings. 5 Click Change Advanced Settings to access settings for battery notification levels, internal storage drive power save time, etc. You can click on the plus signs to expand each item and to see what settings are available for each item.
Mobile Computing Changing the main battery 2 113 While continuing to press Fn, press F2 until you select the desired Power Plan. The Power Plan options are: Balanced, Power Saver, and High Performance. 3 Release the Fn key. The hot key card disappears. You are now in the selected mode. Changing the main battery When your main battery has run out of power, you have two options: plug in the AC adaptor or install a charged main battery.
Mobile Computing Changing the main battery 5 Slide the battery release lock to the unlocked position. (Sample Illustration) Unlocking the battery release lock 6 Slide the battery release latch to release the battery. 7 Pull the discharged battery out of the computer. (Sample Illustration) Removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately.
Mobile Computing Changing the main battery 115 Inserting a charged battery To insert a battery: 1 Wipe the terminals of the charged battery with a clean cloth to ensure a good connection. 2 Insert the charged battery into the slot until the latch clicks. The battery pack has been designed so that you cannot install it with reverse polarity. If the battery does not slide into the slot easily, move the battery release lock to the unlocked position and try again. Do not force the battery into position.
Mobile Computing Taking care of your battery 4 Turn the computer right side up. 5 Reconnect any cables that were removed in step 3 of “Removing the battery from the computer” on page 113. 6 Restart the computer. Taking care of your battery The following sections offer tips on how to take care of your battery and prolong its life.
Mobile Computing Disposing of used batteries 117 Maintaining your battery Fully discharging your battery pack will allow better accuracy of the battery meter. To fully discharge your battery pack: ❖ Periodically, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below: 1 Turn off the computer’s power. 2 Disconnect the AC adaptor and turn on the computer’s power. If it does not turn on, go to step 4.
Mobile Computing Disposing of used batteries Never attempt to dispose of a battery pack by burning or by throwing it into a fire, and never allow exposure to a heating apparatus (e.g., microwave oven). Heat can cause a battery pack to explode and/or release caustic liquid, both which may possibly cause serious injury. Always dispose of used battery packs in compliance with all applicable laws and regulations.
Mobile Computing Traveling tips 119 Traveling tips The environmental precautions listed in “Selecting a place to work” on page 40, also apply while traveling. ❖ Never leave your computer on a sunny ledge or in a place where it could get wet or covered in dust. ❖ Always travel with the computer in a carrying case. Toshiba offers a choice of carrying cases for the computer. They all provide plenty of extra space for manuals, power cords, and compact discs.
Chapter 4 Exploring Your Computer’s Features In this chapter, you will explore some of the special features of your computer. Exploring the desktop The desktop is the launching pad for everything you can do in the Windows® operating system. You use its features to start programs, find documents, set up system components, and perform most other computing tasks. HINT: The illustrated examples in this guide may appear slightly different from the screens displayed by your system.
Exploring Your Computer’s Features Exploring the desktop 121 Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, Taskbar, Notification Area, and background pattern. Icons Start button Taskbar Notification Area (Sample Image) Windows® operating system desktop Icons An icon represents a folder, file, or program that can be quickly activated by double-clicking the icon.
Exploring Your Computer’s Features Exploring the desktop Your desktop may contain other icons depending on your configuration. See Windows® online Help for more specific information on each icon and how to use it.
Exploring Your Computer’s Features Setting up for communications 123 Setting up for communications To connect to the Internet, use an online service, or communicate across the telephone lines with another computer, you need: ❖ A browser or communications program ❖ An Internet Service Provider (ISP) or online service if you plan to use the Internet ❖ A way to connect to the ISP (for example modem/ Wi-Fi®/LAN, etc.
Exploring Your Computer’s Features Setting up for communications Accessing a network To access a network: ❖ At the office, connect an Ethernet cable to the RJ45 jack on your computer. For specific information about connecting to the network, consult your network administrator. Many hotels, airports, and offices offer Wi-Fi® access. If your computer has Wi-Fi®, ask them for help when connecting to their Wi-Fi® network. ❖ While you are at home or traveling, you need a dial-up connection.
Exploring Your Computer’s Features Setting up for communications 125 For more detailed information regarding your computer’s modem, visit Toshiba’s Web site at accessories.toshiba.com. Before you can communicate using the modem, you need to connect it to a telephone line. Your computer’s built-in modem port provides an RJ-11 jack, allowing you to connect the modem to a standard voice-grade telephone line.
Exploring Your Computer’s Features An overview of using the Internet An overview of using the Internet The following sections give a quick introduction to the Internet and some of its exciting features, under these headings: ❖ The Internet ❖ The World Wide Web ❖ Internet Service Providers ❖ Connecting to the Internet ❖ Surfing the Internet ❖ Internet features ❖ Uploading to, and downloading files from, the Internet The Internet The Internet is an association of thousands of networks and
Exploring Your Computer’s Features An overview of using the Internet 127 Connecting to the Internet To connect to the Internet, you need: ❖ A modem and telephone line, or a LAN connection ❖ A Web browser ❖ An Internet Service Provider (ISP) account Once you have established an ISP account, you can connect to the Internet. 1 Connect your computer’s modem (available on certain models) to a telephone line.
Exploring Your Computer’s Features An overview of using the Internet Internet features The Internet offers many types of communication tools to help you perform many tasks. ❖ Internet email To send and receive email of your own, you need a mailbox on the Web or an email address. If you have an account with an ISP, you can probably set up an email address at the same time you sign up for the service.
Exploring Your Computer’s Features Exploring audio features 129 Exploring audio features You can use your computer to record sounds using the computer’s internal microphone (available on certain models) or an optional external microphone. You can listen to sound files or audio CDs using the built-in speakers, headphones, or external speakers. Recording sounds You may record sounds using the computer’s internal microphone (available on certain models) or by connecting an optional external microphone.
Exploring Your Computer’s Features FM tuner TECHNICAL NOTE: When using amplified speakers, use speakers that require an external power source. Other types of speakers will be inadequate to produce sound from the computer. To play back sound files through external speakers or headphones: 1 Locate the headphone jack on the computer. 2 Using any necessary adapters, plug the cable from the headphones or external speakers into the headphone jack. The headphone jack requires a 16-ohm stereo mini-jack.
Exploring Your Computer’s Features Web Camera 131 Web Camera (Available on certain models) Your computer may come with a built-in Web Camera. With this Web Camera you can do the following: ❖ Take pictures and record videos with your computer ❖ Chat with others and have them see you while using instant messaging (IM) programs ❖ Have video conference calls NOTE To E-mail, instant message or video conference, you must be connected to the Internet.
Exploring Your Computer’s Features Using an ExpressCard® 2 Insert the ExpressCard. (Sample Illustration) Inserting an ExpressCard 3 Push the ExpressCard into the slot until it locks in place. Removing an ExpressCard® 1 Prepare the card for removal by clicking the Safely Remove Hardware icon in the Notification Area and then selecting the card or device you want to remove. If the system is unable to prepare the card for safe removal, a message will tell you to try again later.
Exploring Your Computer’s Features Using the Bridge Media Adapter Slot 133 Using the Bridge Media Adapter Slot (Available on certain models) The Bridge Media Adapter slot (available on certain models) supports the use of Memory Stick™, Memory Stick™ PRO, Secure Digital™ (SD™), MMC™ (MultiMediaCard™), or xD-Picture Card™ media. These media can be used with a variety of digital products: digital music players, cellular phones, PDAs, digital cameras, digital video camcorders, etc.
Exploring Your Computer’s Features Using the i.LINK® port Removing memory media 1 Prepare the media for removal by clicking the Safely Remove Hardware icon in the Notification Area and then selecting the card or device you want to remove. If the system is unable to prepare the media for safe removal, a message will tell you to try again later. If the media can be removed now, the system displays Safe to Remove Hardware. 2 Gently press the card inward to release it. The card pops out slightly.
Chapter 5 Utilities Your computer includes several utilities designed to help you to reconfigure your system to best meet your individual needs. Together, these allow you to ascertain certain system details, set additional options, or change default options. These utilities are described in this chapter. NOTE The utilities described in this chapter, and the icons shown in the sample images are applicable only if the related utility is available on your system.
Utilities TOSHIBA Assist ❖ TOSHIBA Accessibility ❖ Fingerprint Authentication Utility ❖ ConfigFree® TOSHIBA Assist The TOSHIBA Assist provides quick access to computer functions and allows you to customize a range of computer settings. To access TOSHIBA Assist, click Start, All Programs, Toshiba, Utilities, and then TOSHIBA Assist. The TOSHIBA Assist window appears.
Utilities TOSHIBA Assist Connect The features available in this category are: ❖ ConfigFree® Connectivity Doctor ❖ Bluetooth® Settings ❖ Bluetooth® Local COM Settings (Sample Image) TOSHIBA Assist window – Connect tab 137
Utilities TOSHIBA Assist Secure The features available in this category are: ❖ Supervisor password ❖ User password (Sample Image) TOSHIBA Assist window – Secure tab
Utilities TOSHIBA Assist 139 Protect & Fix The features available in this category are: ❖ TOSHIBA PC Diagnostic Tool Utility (Sample Image) TOSHIBA Assist window – Protect & Fix tab
Utilities TOSHIBA Assist Optimize The features available in this category are: ❖ Mouse Utility ❖ TOSHIBA Hardware Setup ❖ TOSHIBA Zooming Utility ❖ TOSHIBA Button Support ❖ CD/DVD Drive Acoustic Silencer ❖ TOSHIBA Accessibility ❖ TOSHIBA SD™ Memory Card Format Utility (Sample Image) TOSHIBA Assist window – Optimize tab
Utilities TOSHIBA Application Installer 141 TOSHIBA Application Installer (Available on certain models) The TOSHIBA Application Installer allows you to reinstall the drivers and applications that were originally bundled with your computer. To reinstall drivers and applications: 1 Click Start, All Programs, Toshiba, Recovery, and then TOSHIBA Application Installer. 2 Click Next. (Sample Image) TOSHIBA Application Installer screen 3 Click the item you want to install.
Utilities Setting passwords Setting passwords Setting a password lets you walk away from your computer while providing additional protection for your files. When you set a password, you must enter the password before you can work on your computer again. Toshiba supports several types of passwords on your computer: ❖ NOTE An instant password—Secures your open programs and files when leaving the computer temporarily.
Utilities Setting passwords 143 Using a supervisor password A supervisor password prevents other users from changing hardware configuration options. Setting a supervisor password If you choose to set a supervisor or user password, Toshiba strongly recommends that you save your password in a location where you can later access it should you not remember it. Toshiba is not responsible for any losses that may occur to you, your organization or others as a result of the inability to access your computer.
Utilities Setting passwords 6 Click OK. A pop-up screen appears asking for the User Password Mode. 7 Select whether the user password allows the user to change the hardware configuration: ❖ 8 Able to run HwSetup—User can change the hardware configuration ❖ Unable to run HwSetup—User cannot change the hardware configuration (supervisor password is required) Click OK. 9 Restart the system to complete the process.
Utilities Setting passwords 145 To register a password for the power-on password functions: 1 Click Start, All Programs, Toshiba, Utilities, and then TOSHIBA Assist. The TOSHIBA Assist window appears. 2 On the left side, click the Secure tab. 3 Click the User Password icon. The Password tab of the TOSHIBA Hardware Setup window appears. (Sample Image) Password tab of Hardware Setup window 4 Select Registered. 5 Enter your password, and then enter it again to verify. 6 Click OK to exit.
Utilities TOSHIBA PC Diagnostic Tool Utility 4 Click Not Registered. A pop-up screen appears asking for a password. 5 Enter the user password, then click OK. TOSHIBA PC Diagnostic Tool Utility This utility can help diagnose problems with devices in your computer. Refer to the online Help documentation within the application for additional help. NOTE The TOSHIBA PC Diagnostic Tool utility may show tests for features you do not have. This is normal and does not indicate a problem.
Utilities TOSHIBA SD™ Memory Card Format Utility 147 TOSHIBA SD™ Memory Card Format Utility This utility is used to format SD™ cards used with the Bridge Media Adapter slot. To format an SD memory card using this utility: 1 Click Start, All Programs, Toshiba, Utilities, and then SD Memory Card Format. The TOSHIBA SD Memory Card Format screen appears. (Sample Image) TOSHIBA SD Memory Card Format screen 2 Select the drive corresponding to the SD memory card.
Utilities Mouse Utility Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. To access the Mouse utility: 1 Click Start, Control Panel, and then Mouse under Hardware and Sound, or click the Mouse icon in the Optimize tab of TOSHIBA Assist. The Mouse Properties screen appears.
Utilities TOSHIBA Hardware Setup 149 TOSHIBA Hardware Setup TOSHIBA Hardware Setup is the Toshiba configuration management tool available through the Windows® operating system. To access it: ❖ Click Start, All Programs, Toshiba, Utilities, and then HWSetup, or click the TOSHIBA Hardware Setup icon in the Optimize tab of TOSHIBA Assist. The TOSHIBA Hardware Setup screen appears.
Utilities TOSHIBA Hardware Setup ❖ Display—Allows you to change various default settings for the built-in display NOTE When the computer restarts, it remembers the last configuration. If data does not appear on the display you are using after starting in Sleep Mode, press Fn + F5. For more information, see “Directing the display output when you turn on the computer” on page 69.
Utilities TOSHIBA Hardware Setup NOTE 151 ❖ The “USB Sleep and Charge function” only works for compatible ports. ❖ When “USB Sleep and Charge function” is Enabled, USB bus power (DC 5V) will be supplied to compatible ports even when the power of the computer is turned OFF. ❖ USB bus power (DC 5V) is similarly supplied to the external devices which are connected to the compatible ports. However, some external devices cannot be charged solely by supplying USB bus power (DC 5V).
Utilities TOSHIBA Hardware Setup If the function does not work with Mode-1 setting, change it to Mode-2. Some external devices may not be able to use this function in either mode. When this happens, change the setting to Disabled. Setting item: Enabled (Mode-1) -- Enables the function Enabled (Mode-2) -- Enables the function Disabled (Default) -- Disables the function USB Wakeup function—This function restores the computer from Sleep Mode depending on the external devices connected to the USB ports.
Utilities TOSHIBA Zooming Utility 153 TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot keys (see “Zoom (Display resolution)” on page 209).
Utilities TOSHIBA Button Support To zoom in, hold down the Fn key and press 2; to zoom out, hold down the Fn key and press 1. For more information about how to use the TOSHIBA Zooming Utility, right-click the icon in the Notification Area and then click Help. TOSHIBA Button Support TOSHIBA Button Support allows you to customize the Mute and Media buttons. These buttons are located on the system control panel directly above the keyboard.
Utilities CD/DVD Drive Acoustic Silencer 155 CD/DVD Drive Acoustic Silencer This utility can slow the speed of your optical drive to make it run more quietly. You can use this utility to make listening to music CDs more enjoyable. NOTE When you change the optical drive to “Silence” mode, the setting is only valid for the current Windows® session. If you shut down, restart, log off, or resume from Hibernation, the setting will revert back to Normal speed.
Utilities TOSHIBA Accessibility TOSHIBA Accessibility The TOSHIBA Accessibility utility allows you to use the Fn key to create a hot key combination with one of the function keys without pressing the two keys simultaneously as is usually required. Using Accessibility lets you make the Fn key a sticky key, meaning you can press it once, release it, and then press a function key to activate the hot key function.
Utilities Fingerprint Authentication Utility 157 Fingerprint Authentication Utility (Available on certain models) The fingerprint authentication utility (available on certain models) can be used to replace the keyboard-based user password authentication system when booting up. The fingerprint authentication utility can also be used for user logon. The user’s fingerprint is read; if the system recognizes the fingerprint, the user is automatically logged on.
Utilities Fingerprint Authentication Utility Fingerprint Logon The fingerprint utility enables logon to your computer using fingerprints. During user enrollment, fingerprint samples are saved and associated with the user’s Windows® user account. When the user attempts to log on again, the user’s fingerprint is read and compared with the user’s enrolled fingerprints; if the fingerprint is recognized, user logon is completed.
Utilities Fingerprint Authentication Utility ❖ 159 Avoid the following finger conditions for enrollment or recognition as they may result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate. ❖ Soaked or swollen finger (e.g., after taking bath) ❖ Injured finger ❖ Wet finger ❖ Soiled or oily finger ❖ Extremely dry skin condition on finger Observe the following to improve the fingerprint recognition success rate. ❖ Enroll two or more fingers.
Utilities ConfigFree® ❖ The recognition success rate may differ from user to user. ❖ Toshiba does not guarantee that this fingerprint recognition technology will be error-free. Toshiba does not guarantee that the fingerprint reader will recognize the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility.
Utilities ConfigFree® 161 Starting ConfigFree® To start ConfigFree®, be sure the computer has a wired or wireless connection. Then perform any of the following steps: ❖ Click Start, All Programs, Toshiba, Networking, and then ConfigFree. ❖ Double-click the ConfigFree icon ❖ Press the TOSHIBA Assist button (if applicable to your system) to open the TOSHIBA Assist, and then click the ConfigFree icon. ❖ Click the ConfigFree icon then click the desired utility. NOTE in the Notification Area.
Utilities ConfigFree® ❖ Status of Wireless Connection switch (Sample Image) Connectivity Doctor screen Profile Settings The Profile Settings utility lets you save network settings in “profiles.” ConfigFree® profiles are useful for easily switching network settings and devices. You can switch network settings simply by selecting the profile with the desired settings.
Utilities ConfigFree® To create a profile: 1 Click the icon in the Notification Area. 2 Move the pointer to Profile. 3 Click Open Settings. The ConfigFree Profile Settings window appears. (Sample Image) ConfigFree Profile Settings window 4 Click Add to start the Create Profile Wizard.
Chapter 6 If Something Goes Wrong Some problems you may encounter when using your computer are relatively easy to identify and solve. Others may require help from your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter.
If Something Goes Wrong Problems when you turn on the computer 2 165 Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End Task. Closing the failed program should allow you to continue working. If it does not, continue with the next step. 4 Close the remaining programs one by one by selecting the program name, then End Task.
If Something Goes Wrong Problems when you turn on the computer If you are using an AC adaptor, verify that the computer is receiving power from the external power source by looking at the AC power light. If the indicator is glowing, the computer is connected to a live external power source. The computer starts but when you press a key nothing happens. Verify that the active program accepts text input. Try clicking your mouse on an area where you can type text and try typing again.
If Something Goes Wrong Problems when you turn on the computer 167 If you are running on battery power, it is recommended that you do not leave the computer in Sleep mode for long periods of time. To charge the battery, leave the computer plugged into a live wall outlet for several hours. For more information see “Charging batteries” on page 105. The computer displays the Non-System disk or disk error message. Make sure there is no diskette in the optional external diskette drive.
If Something Goes Wrong The Windows® operating system is not working 5 Verify that the AC adaptor is the correct unit for your computer model. The computer may not be able to start from an AC adaptor that is rated for less current (amperage) than the computer requires, even if the rated voltage is correct, and the plug fits correctly in the DC-IN socket. The labels on the bottom of the computer and the AC adaptor show the specifications for voltage ("V") and current ("A") for each device.
If Something Goes Wrong ® The Windows operating system is not working ❖ Safe Mode with Command Prompt ❖ Enable Boot Logging ❖ Enable low-resolution video (640x480) ❖ Last Known Good Configuration (advanced) ❖ Directory Services Restore Mode ❖ Debugging Mode ❖ Disable automatic restart on system failure ❖ Disable Driver Signature Enforcement ❖ Start Windows® normally 169 When you highlight each option using the arrow keys, Windows® displays information about each option at the bottom afte
If Something Goes Wrong Resolving a hardware conflict The Windows® operating system can help you If the operating system has started properly but you still have a problem using your computer, the online Help can assist you in troubleshooting the problem. To access the Windows® operating system Help and Support: 1 Click Start, then click Help and Support, or press F1. The Help and Support window appears.
If Something Goes Wrong Resolving a hardware conflict 171 The device most recently connected to the system is the one most likely to be causing a conflict. Resolving conflicts There are several things you can do to resolve hardware conflicts: ❖ Get the most recent drivers from the manufacturer. ❖ Disable the device. For an older device, remove it from the computer. ❖ Disable another system component and use its resources for the new device. See “Fixing a problem with Device Manager” on page 171.
If Something Goes Wrong Resolving a hardware conflict ❖ The Resources tab, which lists resources assigned to the monitor, optional external optical drive, optional external diskette drive, and other power-using functions. This tab does not appear if the device is not using resources. ❖ The Driver tab, which displays the drivers being used by the device. This tab also provides options for updating the driver or rolling back the driver in case the new version is causing a problem.
If Something Goes Wrong Resolving a hardware conflict NOTE 173 For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. Power and the batteries Your computer receives its power through the AC adaptor and power cord/cable or from the system batteries (battery, optional secondary battery, and real-time clock (RTC) battery). Power problems are interrelated.
If Something Goes Wrong Resolving a hardware conflict The battery appears not to power the computer for as long as it usually does. If you frequently repeat shallow charge and discharge, the battery meter may become inaccurate. Let the battery discharge completely, then try charging it again. Check the power options via your Power Plans (see “Power Plans” on page 111).
If Something Goes Wrong Resolving a hardware conflict 175 Nothing happens when you press the keys on the external keyboard. You may have plugged the external keyboard in while the computer was turned on. Using the computer’s TouchPad: 1 Click Start, and then click the arrow next to the Lock button in the lower-right part of the Start menu. The Shut Down menu appears. 2 Click Restart. The computer will restart and recognize the device.
If Something Goes Wrong Resolving a hardware conflict ❖ Try adjusting the contrast and brightness controls on the external monitor. ❖ Press Fn and F5 simultaneously to make sure the display priority is not set for the built-in screen. The screen does not look right. You can change the display settings by clicking a blank area of the desktop with the secondary control button, then clicking Personalize. This opens the Personalization window.
If Something Goes Wrong Resolving a hardware conflict 177 Small bright dots appear on your TFT display when you turn on your computer. Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using highprecision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology.
If Something Goes Wrong Resolving a hardware conflict 6 7 You can choose one or both options: ❖ Automatically fix file system errors ❖ Scan for and attempt recovery of bad sectors Click Start. Error-checking tests and repairs the disk. Your hard disk seems very slow. If you have been using your computer for a long time, your files may have become fragmented. Run Disk Defragmenter. To do this, click Start, All Programs, Accessories, System Tools, and then Disk Defragmenter.
If Something Goes Wrong Resolving a hardware conflict 179 Optical drive problems You cannot access a disc in the drive. If the optical drive is an external drive, make sure that the drive’s cable is properly connected to the computer. Make sure the tray that holds the optical disc is closed properly. Press gently until it clicks into place. Open the tray and remove the disc. Make sure the tray is clean. Any dirt or foreign object can interfere with the laser beam. Examine the disc to see if it is dirty.
If Something Goes Wrong Resolving a hardware conflict The disc will not come out of the drive when you click the eject button on the screen. Press the button on the optical drive itself. For additional information see “You press the disc eject button, but the drive tray does not slide out.” on page 179. Sound system problems No sound is coming from the computer’s speakers. Adjust the volume control. Try pressing Fn + Esc to see if volume mute is disabled.
If Something Goes Wrong Resolving a hardware conflict 181 ExpressCard® checklist ❖ Make sure the card is inserted properly into the slot. ❖ Make sure all cables are securely connected. ❖ Occasionally a defective ExpressCard®slips through quality control. If another computer with a ExpressCard slot is available, try the card in that machine. If the card malfunctions again, it may be defective.
If Something Goes Wrong Resolving a hardware conflict 3 Select the item you wish to remove and click OK. 4 Remove the device when told it is safe to do so. Never swap modules when the computer is in Hibernation or Sleep mode. This is known as “warm swapping” and is not supported. For more information on Hibernation and Sleep modes see “Hibernation mode” on page 74 and “Sleep mode” on page 75. The system does not recognize your ExpressCard®. Refer to the ExpressCard® documentation.
If Something Goes Wrong Resolving a hardware conflict 183 Try printing another file. For example, you could create and attempt to print a short test file using Notepad. If a Notepad file prints correctly, the problem may be in your original file. If you cannot resolve the problem, contact the printer’s manufacturer. The printer will not print what you see on the screen. Many programs display information on the screen differently from the way they print it. See if your program has a print preview mode.
If Something Goes Wrong Resolving a hardware conflict Wireless networking problems NOTE This section provides general troubleshooting tips for networking problems, specifically wireless (Wi-Fi®) networking. The terms and concepts used assume a basic understanding of networks, and may be for more advanced users. If you need assistance or if you are not familiar with the terminology, please see Windows® Help and Support or contact your computer technician.
If Something Goes Wrong Resolving a hardware conflict ❖ ❖ 185 Verify that the network connection is configured to obtain its Internet Protocol (IP) address dynamically: 1 Click Start, and then Network. 2 Click View Status. 3 Click Details. 4 Verify that the DHCP Enabled setting is set to Yes. 5 Click Close. Use IPCONFIG to verify that the computer has a useful IP address—one other than the private address of 169.254.xxx.xxx assigned by Windows®. 1 Click Start to open the Start menu.
If Something Goes Wrong DVD operating problems The Windows® operating system wireless management facility does not work. If you are using an external Wi-Fi® adapter (an ExpressCard®, USB adapter, or other variety), check if the adapter comes with its own management utility. If it does, the utility may be disabling the Windows® operating system wireless management facility, in which case you must use the adapter's management utility.
If Something Goes Wrong Develop good computing habits 3 Select Never on When to turn off the display. 4 Click Save changes. 187 The screen saver runs while you are watching a movie or title. If the screen saver is enabled, it runs on top of any movie or title you are watching. To disable the screen saver: 1 Right-click on the desktop and click Personalize in the menu. 2 Select None for the screen saver. 3 Click OK. Develop good computing habits Save your work frequently.
If Something Goes Wrong Develop good computing habits Read the user’s guides. It is very difficult to provide a fail-safe set of steps you can follow every time you experience a problem with the computer. Your ability to solve problems will improve as you learn about how the computer and its software work together. Get familiar with all the user’s guides provided with your computer, as well as the manuals that come with the programs and devices you purchase.
If Something Goes Wrong Develop good computing habits 189 4 In the input field, enter a name that is descriptive enough to be easily understood in the future, such as “Before installing Brand X Accounting app.” Then click Create. 5 The Windows® operating system creates the Restore Point, automatically stamps it with the current date and time, and displays a message that the restore point was successfully created. 6 Click OK.
If Something Goes Wrong Develop good computing habits Backing up your data or your entire computer with the Windows® operating system The most valuable component of your computer system is the data you create and store on its internal storage drive. Since problems with either hardware or software can make the data inaccessible or even destroy it, the next most valuable component of your computer system may be a recent backup of your data.
If Something Goes Wrong Develop good computing habits 191 General tips for installing hardware and software Here are a few tips to help ensure safe and easy installation of new hardware (printers, pointing devices, external hard drives, DVD writers, scanners, etc.) and software (applications like Microsoft® Office and Adobe® Photoshop®, or utility software such as special toolbars for your web browser). ❖ Create a Restore Point (refer to “Saving system configuration with Restore Points” on page 188).
If Something Goes Wrong Develop good computing habits 3 Install one item of hardware or software. 4 Restart the Windows® operating system. 5 Use the new hardware or software for a while, noting any new problems. Make sure that your critical applications (email, business applications, etc.) are working correctly, and verify that important devices are still functioning.
If Something Goes Wrong If you need further assistance NOTE 193 Before connecting the eSATA device to your computer and external power source, read the documentation that came with the device and follow the manufacturer’s instructions. If you need further assistance If you have followed the recommendations in this chapter and are still having problems, you may need additional technical assistance. This section contains the steps to take to ask for help.
If Something Goes Wrong Other Toshiba Internet Web sites Toshiba voice contact Before calling Toshiba, make sure you have: ❖ Your computer’s serial number ❖ The computer and any optional devices related to the problem ❖ Backup copies of your Windows® operating system and all other preloaded software on your choice of media ❖ Name and version of the program involved in the problem along with its installation media ❖ Information about what you were doing when the problem occurred ❖ Exact err
If Something Goes Wrong Toshiba’s worldwide offices 195 France Toshiba Systèmes (France) S.A. 7, Rue Ampère; B. P. 131 92800 Puteaux Cédex France Germany Toshiba Europe GmbH Leibnizstraße 2 D-93055 Regensburg Germany Italy Centro Direzionale Colleoni Palazzo Perseo Via Paracelso 10 20041, Agrate Brianza Milano, Italy Japan Toshiba Corporation, PCO-IO 1-1, Shibaura 1-Chome Minato-Ku, Tokyo, 105-8001 Japan Latin America and Caribbean Toshiba America Information Systems 9740 Irvine Blvd.
Appendix A Hot Keys/TOSHIBA Cards Hot keys and TOSHIBA Cards provide a quick way to modify selected system functions and to launch applications. There are two types of TOSHIBA Cards: Hot Key Cards and Application Cards. Hot Key Cards The Hot Key Cards are used to set or modify the following system functions: ❖ Mute ❖ Lock (Instant security) ❖ Power Plan ❖ Sleep ❖ Hibernation ❖ Output (Display switch) ❖ Brightness control ❖ Wireless ❖ TouchPad ❖ Zoom (Display resolution) 196 5.375 x 8.
Hot Keys/TOSHIBA Cards Hot Key Cards 197 Using the Hot Key Cards The Hot Key Cards are normally hidden from view. The Cards appear when you press the Fn key. NOTE Hot keys are keys that, when pressed in combination with the Fn key, turn system functions on and off. Hot keys have a legend on the key indicating the option or feature the key controls. To use the Hot Key Cards: 1 Press and hold the Fn key. The TOSHIBA Cards appear along the top of the screen.
Hot Keys/TOSHIBA Cards Application Cards Application Cards The Application Cards are used to launch these applications: TOSHIBA Assist For more information, refer to “TOSHIBA Assist” on page 136. PC Diagnostic Tool utility For more information, refer to “TOSHIBA PC Diagnostic Tool Utility” on page 146. ConfigFree utility For more information, refer to “ConfigFree®” on page 160. Bluetooth settings This Application Card launches your Bluetooth® settings.
Hot Keys/TOSHIBA Cards Application Cards 199 Using the Application Cards To launch an application using the Application Cards: 1 Press and hold the Fn key. The TOSHIBA Cards display at the top of the screen. “stacked” Card (Sample Image) TOSHIBA Card display 2 Click the “stacked” card on the far right of the display. The Application Cards are hidden under this card. The Application Cards appear, and the Hot Key Cards are stacked under the Card on the far left.
Hot Keys/TOSHIBA Cards Hot key functions 3 4 5 The Card Case displays two rows of Cards. Cards that appear solid (not transparent) in the bottom row are enabled and can be selected when the Application Cards are displayed. The top row contains all of the disabled cards. To enable a card, drag it from the top row to the bottom row. To disable the card, drag it from the bottom row to the top row. To close the Card Case, click the icon in the top corner of the screen.
Hot Keys/TOSHIBA Cards Hot key functions 201 Lock (Instant security) This TOSHIBA Card or hot key blanks the display. Selecting this Card or pressing the hot key displays the following options: or Fn + (Sample Image) Security options ❖ To enable lock, select ❖ To cancel, select . . The Fn + F1 hot key function activates instant security. The user logon screen will appear and a user with a valid account will need to log back on to gain access to the computer. 5.375 x 8.375 ver 2.
Hot Keys/TOSHIBA Cards Hot key functions Power plan This TOSHIBA Card or hot key displays the power plans and cycles through the power plans. or Fn + The properties of each power plan, and the power plans that are displayed by this function, are set in the Power Options window. Selecting this Card or pressing the hot key displays the currently selectable power plans: (Sample Image) Power Plan options Cycle through the power plans, then select the desired power plan. 5.375 x 8.375 ver 2.
Hot Keys/TOSHIBA Cards Hot key functions 203 Sleep mode This TOSHIBA Card or hot key places the computer into Sleep mode. For more information about Sleep mode, please see “Using and configuring Sleep mode” on page 81. or Fn + Selecting this Card or pressing the hot key displays the following options: (Sample Image) Sleep options ❖ To enable Sleep mode, select ❖ To cancel, select 5.375 x 8.375 ver 2.3 . .
Hot Keys/TOSHIBA Cards Hot key functions Hibernation mode This TOSHIBA Card or hot key places the computer into Hibernation mode. or Fn + If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page 78. Selecting this Card or pressing the hot key displays the following options: (Sample Image) Hibernation options ❖ To enable Hibernation mode, select ❖ To cancel, select 5.375 x 8.375 ver 2.3 . .
Hot Keys/TOSHIBA Cards Hot key functions 205 Output (Display switch) or This TOSHIBA Card or hot key cycles through the poweron display options (only the first option is available when you do not have an external monitor attached) (the last option is available only if you are in Extended Display Mode). NOTE Fn + Some modes are only available with the appropriate device attached and turned on.
Hot Keys/TOSHIBA Cards Hot key functions Cycle through the display modes, then select the desired mode. Not all functions are supported on all models. NOTE Some systems also support an additional Swap Image Display mode. This mode is available only if the current setting is an extended desktop mode (Built-in Display and External Monitor, or Built-in Display and TV). In extended desktop mode, the image is split into two sides, one side per display device. To swap sides, select Swap Image Display.
Hot Keys/TOSHIBA Cards Hot key functions 207 Disabling or enabling wireless devices This TOSHIBA Card or hot key enables/disables the optional wireless devices* installed in your computer. The wireless modes are: or ❖ Wi-Fi® enabled—Enables just the Wi-Fi® module. ❖ Bluetooth® enabled—Enables just the Bluetooth® module. ❖ All disabled—Disables the Bluetooth® and Wi-Fi® modules. ❖ All enabled—Enables the Bluetooth® and Wi-Fi® modules.
Hot Keys/TOSHIBA Cards Hot key functions Disabling or enabling the TouchPad™ This TOSHIBA Card or hot key enables/disables the TouchPad. For more information on using the TouchPad, see “Disabling or enabling the TouchPad™” on page 68. or Fn + Selecting this Card or pressing the hot key displays the following options: (Sample Image) Disable or Enable TouchPad options ❖ To enable the TouchPad, select . ❖ To disable the TouchPad, select . 5.375 x 8.375 ver 2.
Hot Keys/TOSHIBA Cards Hot key functions 209 Zoom (Display resolution) This TOSHIBA Card or hot key switches screen resolution. Selecting this Card or pressing the hot key displays the following options: or Fn + [Space bar] (Sample Image) Screen resolution options Cycle through the screen resolutions, then select the desired resolution. 5.375 x 8.375 ver 2.
Hot Keys/TOSHIBA Cards Hot key functions Keyboard hot key functions Fn + This hot key turns the cursor control overlay on and off. Fn + This hot key turns the numeric overlay on and off. Fn + This hot key turns the scroll lock feature on and off. Fn + This hot key turns the TOSHIBA Zooming Utility to zoom-out. Fn + This hot key turns the TOSHIBA Zooming Utility to zoom-in. 5.375 x 8.375 ver 2.
Appendix B Power Cord/Cable Connectors Your computer ships with the correct power supply for the country of purchase. This appendix shows the shapes of the typical AC power cord/cable connectors for various parts of the world. USA and Canada United Kingdom UL approved CSA approved BS approved Australia Europe AS approved VDA approved NEMKO approved 211 5.375 x 8.375 ver 2.
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide.
Glossary DOS disk operating system DPI dots per inch DSTN dual supertwist nematic DVD digital versatile (or video) disc 213 DVD-ROM digital versatile (or video) disc read-only memory ECP enhanced capabilities port EPROM erasable programmable read-only memory FAT file allocation table FCC Federal Communications Commission GB gigabyte HDD hard disk drive HTML Hypertext Markup Language IEEE Institute of Electrical and Electronics Engineers I/O input/output IRQ interrupt request IS
Glossary SDRAM synchronous dynamic random access memory SRAM static random access memory SSD Solid State Drive SVGA super video graphics adapter TFT thin film transistor USB universal serial bus URL uniform resource locator WAN wide area network www World Wide Web Terms The following terms may appear in this user’s guide. A active-matrix display — A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology.
Glossary 215 baud rate — The speed at which a communication device, such as a printer or modem, transmits information. Baud rate is the number of signal changes per second (not necessarily the same as bits per second). See also bits per second. BIOS (basic input/output system) — Basic instructions, stored in readonly memory (ROM), containing the information the computer needs to check hardware and load the operating system when you start up the computer.
Glossary central processing unit (CPU) — The chip that functions as the “brain” of the computer. It takes information from outside sources, such as memory or keyboard input, processes the information, and sends the results to another device that uses the information. character — Any letter, number, or symbol you can use on the computer. Some characters are non-printing characters, such as a paragraph break in a word-processing program. A character occupies one byte of computer storage.
Glossary D 217 default — The setting selected by a program when the user does not specify an alternative setting. device — A component attached to the computer. Devices may be external (outside the computer’s case) or internal (inside the computer’s case). Printers, disk drives, and modems are examples of devices. device driver — A program (called a “driver”) that permits a computer to communicate with a device.
Glossary double-click — To press and release the pointing device’s primary button rapidly twice without moving the pointing device. In the Windows® operating system, this refers to the pointing device’s left button, unless otherwise stated. double-density diskette — A 3.5-inch diskette that can hold up to 720 KB of information (half the capacity of a high-density diskette). See also diskette, high-density diskette.
Glossary F 219 file — A collection of related information, saved on disk with a unique name. A file may be a program, information used by a program, or a document. See also document. file allocation table (FAT) — The section of an internal storage drive that keeps track of the location of stored files. file name — A set of characters that uniquely identifies a file within a particular folder. It consists of two parts: the actual name and the file name extension. See also file extension.
Glossary Hibernation — A feature of many Toshiba computers that saves to the internal storage drive the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned off. See also Sleep, Suspend. high-density diskette — A 3.5-inch diskette that holds 1.44 MB of data. See also diskette.
Glossary 221 liquid crystal display (LCD) — A type of display that uses a liquid substance between two transparent electrode panels. When an electric current passes through the electrodes, the molecules in the liquid form a crystalline pattern that polarizes the light passing through it. A filter over the electrodes permits only non-polarized light to pass to the surface of the display, creating light and dark pixels.
N Glossary network — A collection of computers and associated devices that are connected by communications facilities. A network allows you to share data and peripheral devices, such as printers, with other users and to exchange electronic mail. non-interlaced — A method of refreshing a computer screen, in which each pixel of every line is refreshed as the electron beam scans across and down the screen. Compare interlaced.
Glossary 223 Plug and Play — Generally, refers to the computer’s ability to automatically configure itself to work with peripheral devices. When capitalized, refers to a standard that, when followed by a device manufacturer, allows a computer to configure itself automatically to work with the device. pointing device — Any device, such as the TouchPad or a mouse, that enables you to move the cursor on the screen.
Glossary RJ11 — A modular connector used on most U.S. telephone systems and direct-connect modems. The RJ11 connector is a 6-wire connector. ROM (read-only memory) — Non-volatile memory that can be read but not written to. Non-volatile here means that information in ROM remains whether or not the computer is receiving power. This type of memory is used to store your computer’s BIOS, which is essential instructions the computer reads when you start it up. See also BIOS, memory. Compare RAM.
Glossary T U 225 TFT display — See active-matrix display. universal serial bus (USB) — USB is a serial bus that supports a data transfer rate of up to 480 Mbps (480 million bits per second). USB can connect up to 127 peripheral devices through a single allpurpose USB port. USB allows hot swapping of peripherals. See also bus, hot swapping, serial. upload — To send a file to another computer through a modem or network. See also download. USB — See universal serial bus (USB).
Index A AC adaptor 46 AC power connecting adaptor 47 accessories memory 51 adding memory 51 Alt keys 89 Application Cards 198 audio files 129 audio features 129 B backing up files 87 battery changing 113 charge indicator light 48, 107 charge not lasting 174 charging 46, 48 conserving power 110 disposal 117 low charge 109 monitoring power 48, 107 not charging 173 226 notifications 109 power plan 202 power plan hot key 112 real-time clock (RTC) 104 removing 113 BIOS Setup see TOSHIBA Hardware Setup Bridge
Index moving 84 non-system disk or disk error message 167 not accessing disk drives 166 running on battery power 103 setting up 43, 53 warning resume failure message 166 computer lock 85 computing tips 86 ConfigFree® 160 connecting 69 connecting to a power source 46 connection set up 124 control buttons 68 Ctrl keys 89 D desktop creating new icon 121 major features 121 desktop exploration 120 desktop icons 121 Device Manager 171 checking properties 171 devices keyboard 71 mouse 71 Disk Defragmenter 178 di
Index external diskette drive connecting 73 external display, adjusting 71 F FAT (File Allocation Table) 177 file extensions 95 file, backing up 87 files backing up 96 printing 95 restoring 96 saving 93 fingerprint authentication 157 fingerprint Authentication Utility using 157 FM tuner 130 Fn keys 89 function keys 89 H hard drive recovery utilities 60 hardware conflicts 170 resolving 171 headphones using 129 Help and Support Windows® operating system 170 Hibernation mode 74 configuring 78 starting
Index troubleshooting 174 using 88 keyboard, external 71 keyboard, full-size 88 L lock computer, using 85 M main battery removing 113 memory adding 51 problem solving 172 removing memory module slot cover 54 memory module inserting 55 installation 52 removing 58 memory module slot 54 microphone 129 modem connecting to telephone line 124 problem solving 183 monitor 68 connecting 68 not working 175 mouse installing 71 mouse utility 148 N network accessing 124 Connect to the Internet 124 networking wireles
Index using Shut Down 76 using Sleep 81 precautions 41 primary button 68 printer connecting 71 problem solving 182, 183 printing a file 95 problem solving AC power 173 accessing disk drives 166 battery charge does not last 174 battery not charging 173 cannot insert diskette in drive 178 cannot read a diskette 178 changing display properties 176 checking device properties 171 computer hangs when ExpressCard® inserted 181 computer will not power up 165 contacting Toshiba 193 corrupted/damaged data files
Index precautions 41 saving files 93 screen blank 175 does not look normal/flickers 176 secondary button 68 set up communications 123 setting up adding memory 51 computer 43, 53 work environment 40 setting up a connection 124 Sleep mode 75 hot key 203 starting again from 83 sound problem solving 180 sounds recording 129 speakers using external 129 start button 122 Start Search field 93 starting a program 91 Start Search field 93 Windows® Explorer 92 Windows® Start menu 91 starting up the computer from Shut
Index Windows® Start menu 91 wireless networking 123 Wizards Connect to the Internet 124 World Wide Web 126 www 126
