User's Manual DX 730
Table of Contents Preface General Precautions Chapter 1 Getting Started Equipment checklist ............................................................................. 1-1 Getting Started ....................................................................................... 1-2 Chapter 2 The Grand Tour Computer ................................................................................................ 2-1 Wireless Keyboard ..........................................................................
Chapter 4 Utilities & Advanced Usage Utilities and Applications ...................................................................... 4-1 Special features ..................................................................................... 4-5 Using the TOSHIBA Sleep Utility ......................................................... 4-7 TOSHIBA Password Utility ................................................................... 4-9 HW Setup .................................................................
Copyright © 2012 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein. First edition June 2012 Copyright authority for music, movies, computer programs, databases and other intellectual property covered by copyright laws belongs to the author or to the copyright owner.
Memory Stick and Memory Stick PRO are trademarks or registered trademarks of Sony Corporation. MultiMediaCard and MMC are trademarks of MultiMediaCard Association. Blu-ray Disc™, Blu-ray™, Blu-ray 3D™, BDXL™ and the logos are trademarks of the Blu-ray Disc Association. QUALCOMM is a trademark of Qualcomm Incorporated, registered in the United States and other countries. ATHEROS is a trademark of Qualcomm Atheros, Inc., registered in the United States and other countries.
2. This device must accept any interference received, including interference that may cause undesired operation. Contact Address: TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618-1697 Telephone: (949) 583-3000 EU Declaration of Conformity This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CEMarking is TOSHIBA Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany.
product in working environments other than the above mentioned “Residential, commercial and light industry environments”. For example, the following environments are not approved: Industrial Environments (e.g. environments where a mains voltage of 380 V three-phase is used) Medical Environments Automotive Environments Aircraft Environments Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of TOSHIBA.
AND LICENSING MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM. Canadian regulatory information (Canada only) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications.
Disposal of batteries and/or accumulators The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators must be collected and disposed of separately from household waste. If the battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery Directive (2006/66/ EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.
Following information is only for Turkey: Compliant with EEE Regulations: TOSHIBA meets all requirements of Turkish regulation 26891 “Restriction of the use of certain hazardous substances in electrical and electronic equipment”. The number of possible pixel failures of your display is defined according to ISO 9241-307 standards. If the number of pixel failures is less than this standard, they will not be counted as defect or failure.
Optical disc drive safety instructions Be sure to check the precautions at the end of this section. The drive model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
Preface Congratulations on your purchase of this computer. This powerful computer provides excellent expansion capability, includes multimedia functionality, and is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions. Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment. Please read. A note is a hint or advice that helps you make best use of your equipment. Terminology This term is defined in this document as follows: User's Manual Start The word "Start" refers to the " Windows 7.
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
that can be caused by extensive keyboard use. It also includes information on work space design, posture and lighting that can help reduce physical stress. Heat injury If the computer has been used for a long time, avoid direct contact with the metal plate supporting the various interface ports as this can become hot. The surface of the AC adaptor can become hot when in use but this condition does not indicate a malfunction.
Chapter 1 Getting Started This chapter provides an equipment checklist, and basic information to start using your computer. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.
TOSHIBA Flash Cards TOSHIBA Disc Creator TOSHIBA VIDEO PLAYER TOSHIBA Resolution+ Plug-in For Windows Media Player TOSHIBA Blu-ray Disc Player Corel Digital Studio for TOSHIBA TOSHIBA Media Controller TOSHIBA HDD/SSD Alert Utility TOSHIBA eco Utility TOSHIBA HW Setup Utility TOSHIBA PC Diagnostic Tool TOSHIBA Web Camera Application TOSHIBA Accessibility TOSHIBA Service Station TOSHIBA PC Health Monitor TOSHIBA Sleep Utility CyberLink PowerCinema for TOSHIBA CyberLink YouPaint User's Manual (this manual) You
Use a virus-check program and make sure it is updated regularly. Never format storage media without checking its content - formatting destroys all stored data. It is a good idea to periodically back up the internal hard disk drive or other main storage device to external media. General storage media is not durable or stable over long periods of time and under certain conditions may result in data loss.
When you connect the AC adaptor to the computer, always follow the steps in the exact order as described in the User’s Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.
2. Connect the AC adaptor’s DC output plug to the DC IN 19V jack on the back of the computer. Figure 1-3 Connecting the DC output plug to the computer 2 1 1. DC output plug 3. 2. DC IN 19V jack Plug the power cord into a live wall outlet - the Power indicator on the front of the computer should glow. Be careful not to place your fingers on the hinge between the computer’s back and the stand as this could cause personal injury such as the finger pinch.
Keep the computer and wireless keyboard/mouse in a certain distance, otherwise the keyboard/mouse will not work properly. Installing the battery of the keyboard and mouse Installing the batteries of the mouse 1. 2. Open the battery cover on your wireless mouse. Put two AAA batteries into the battery groove. Figure 1-5 Installing the batteries of the mouse 1 2 1. Battery cover 3. 2. Batteries Close the battery cover. Installing the batteries of the keyboard 1. 2.
2. Press the Connect button of the dongle using a slender object such as a tweezers. Figure 1-7 Press the Connect button of the dongle 1 2 1. Connect button 3. 4. 2. Tweezers Slide the Power switch on the back of the keyboard/mouse to the ON position. Press the Connect button of the keyboard/mouse. Please refer to the Wireless Keyboard and Wireless Mouse section in Chapter 2, Grand Tour for the location of the connect button. The connection will be established.
Starting up for the first time The Windows 7 Startup Screen will be the first screen displayed when you turn on the power. Follow the on-screen instructions on each screen in order to properly install the operating system. When it is displayed, be sure to read the Software License Terms carefully. Turning off the power The power can be turned off in one of three modes, either Shut Down Mode, Hibernation Mode or Sleep Mode.
When you have to turn off your computer aboard an aircraft or in places where electronic devices are regulated or controlled, always completely shut down the computer. This includes turning off any wireless communication functionalities, and cancelling settings that reactivate the computer automatically, such as a timer recording function.
Press the power button. Please note that this feature must be enabled within the Power Options (to access it, click Start -> Control Panel -> System and Security -> Power Options). When you turn the power back on, you can continue where you left when you shut down the computer. When the computer is in Sleep Mode, the power indicator will blink amber. Sleep Mode limitations Sleep Mode will not function under the following conditions: Power is turned back on immediately after shutting down.
Automatic Hibernation Mode The computer can be configured to enter Hibernation Mode automatically when you press the power button. In order to define these settings, you can follow the steps as described below: 1. 2. 3. 4. 5. Click Start and click the Control Panel. Click System and Security and click Power Options. Click Choose what the power buttons do. Enable the desired Hibernation Mode settings for When I press the power button. Click the Save changes button.
Chapter 2 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section in Appendix C. Please handle your computer carefully to avoid scratching or damaging the surface. Computer Front side The following figure shows the computer’s front side.
Bluetooth antennas Some computers in this series are equipped with Bluetooth antennas. Wireless LAN antennas Some computers in this series are equipped with the Wireless LAN antennas. Legal Footnote (Wireless LAN) For more information regarding Wireless LAN, please refer to the Legal Footnotes section in Appendix C. Microphone A built-in microphone allows you to import and record sounds into your application. Web Camera LED The Web Camera LED glows when the Web Camera is operating.
Power button Press this button to turn the computer's power on and off. When connected to the AC adaptor, the Power indicator normally glows white when the computer is turned on and glows amber when the computer is off. However, if you turn the computer off into Sleep Mode, this indicator will flash amber - approximately two seconds on, two seconds off. Stereo speakers The speakers emit sound generated by your software as well as audio alarms generated by the system. Display screen 58.
Figure 2-2 The left side of the computer 1 2 3 4 5 6 7 8 9 10 1. Display off button 2. AV select button 3. Brightness up button 4. Brightness down button 5. Volume up button 6. Volume down button 7. Memory media slot 8. Headphone jack 9. Microphone jack 10.Universal Serial Bus (USB 3.0) ports Product appearance depends on the model you purchased. Display off button Press this button to turn off the computer’s display panel. AV select button Press this button to switch the AV input mode.
Memory media slot This slot lets you insert an SD™/SDHC™/ SDXC™ memory card, miniSD™/microSD™ Card, Memory Stick™ (PRO™) and MultiMediaCard™. Refer to the Optional devices section in Chapter 3, Operating Basics for more information. Headphone jack A 3.5 mm mini headphone jack enables connection of stereo headphones. Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for stereo microphone input. The microphone jack has Sleep and Music function.
Figure 2-3 The right side of the computer 1 1. Optical disc drive Optical disc drive The computer may be configured with a DVD Super Multi, Blu-ray™ Combo drive or Blu-ray™ Writer drive (BDXL™). 2.6GB and 5.2GB DVD-RAM media cannot be read from or written to. Back The following figure shows the computer’s back.
Figure 2-4 The back of the computer 1 2 3 4 5 6 7 10 8 11 9 1. Cooling vents 2. Memory module slots 3. TV antenna jack* 4. HDMI out port* 5. HDMI input port 6. Universal Serial Bus (USB 2.0) ports 7. Universal Serial Bus (USB 3.0) ports 8. LAN jack 9. DC IN 19V jack 10. Security lock slot 11. Wireless receiver (dongle) slot * Provided with some models. Product appearance depends on the model you purchased. Cooling vents The cooling vents help the processor to avoid overheating.
Memory module slot The memory module slot allows for the installation, replacement and removal of additional memory module. The size of memory modules varies depending on the model. The actual amount of useable system memory will be less than the installed memory modules. Refer to the Additional memory module section in Chapter 3, Operating Basics. Some models are provided with four memory module slots and only two of the memory module slots are user-accessible.
LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). Refer to chapter 3, Operating Basics, for details. Do not connect any cable other than a LAN cable to the LAN jack. It could cause damage or malfunction. Do not connect the LAN cable to a power supply. It could cause damage or malfunction.
Figure 2-6 Back of the wireless keyboard 1 2 3 4 1. Stand 2. Connect button 3. Power switch (keyboard) 5 4. Battery cover 5. Stand Stand Used to let the keyboard tilted at an angle. Connect button This button is not used under normal conditions. Power switch (keyboard) Used to turn on the power of the keyboard. Battery cover Used for covering the battery of the keyboard Wireless Mouse Front The following figure shows the front of the wireless mouse.
Right button Using for normal right controls of the mouse. Left button Using for normal left controls of the mouse. Back The following figure shows the back of the wireless mouse. Figure 2-8 Back of the wireless mouse 1 3 2 4 1. Power switch (mouse) 2. Optical sensor 3. Connect button 4. Battery cover Power switch (mouse) Using for turning on the power of the mouse. Optical sensor Using for locating the position of the mouse. Connect button This button is not used under normal conditions.
Figure 2-9 Remote controller 2 3 1 5 6 4 7 9 10 8 11 12 13 14 15 17 16 18 19 20 21 22 23 24 25 1. Power 8. Red Button 2. Start 3. Teletext 4. Recorded TV 5. Guide 9. Green Button 10.Yellow Button 11. Blue Button 12. Back 6. Live TV 13. More Information 14. Channel/Page Control 15. Arrows and OK 16. Mute 17. Replay 18. Skip 19. Record 20. Pause 21.Stop 22. Volume Control 23. Play 24. FWD (Fast Forward) 25. REW (Rewind) 7.
Guide Opens the Television Program Guide to display available TV channels and programs to watch and record. Live TV A shortcut to the full screen view. It also takes you to the current point in a live TV program after pausing live TV. DVD Menu Opens the main menu on a DVD movie, if available. Red, Green, Yellow and Blue buttons It jumps to a registration link.These buttons are not provided with some models. Back Displays the previous window.
Play Plays the selected media. FWD (Fast Forward) Moves the media (video, disc, music, and so on) forwards. REW (Rewind) Moves the media (video, disc, music, and so on) backwards. Using the Remote Controller Some computers include a remote control unit, which allows you to control some of your computer’s functions from a distant location. The remote controller is designed specifically for this computer. Some application programs may not support remote control functions.
Store the battery for the remote control beyond the reach of children. If a child swallows a battery, this might result in choking. If it happens, contact a doctor immediately. Observe the following precautions when using the battery of the Remote Controller. Do not use battery other than those specified. Ensure that you insert the battery with its polarities correctly aligned (+ or -). Do not recharge, heat, disassemble or short the battery, or put it into a fire or flame.
2. Slide the battery out of battery case. Figure 2-10 Installing/Replacing the battery MCE IR Remote Control Model: G83C000BF116 1x 3V CR2032 Lithium battery RC6 ir Made in China 3. 4. Insert the new battery in place. Be sure to place the battery with correct polarities. Push it forward to fit into the battery case. Close the battery cover securely. Internal Hardware Components This section describes the internal hardware components of your computer.
For more information regarding Hard Disk Drive (HDD) Capacity, please refer to the Legal Footnotes section in Appendix C. RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. Video RAM The memory in a computer's graphics adaptor, used to store the image displayed on a bitmap display. The amount of Video RAM available is dependent on the computer's system memory. Start -> Control Panel -> Appearance and Personalization -> Display -> Adjust resolution.
Graphics Control Some NVIDIA graphics models may include NVIDIA® Optimus™ technology feature. NVIDIA® Optimus™ technology intelligently optimizes All-In-One PC performance by seamlessly switching between a discrete NVIDIA GPU for great graphics performance and an Intel integrated graphics chip for sustained battery life. Switching is automatic and does not require the user to reboot the computer.
Chapter 3 Operating Basics This chapter describes the basic operations of your computer, highlights the precautions that should be taken when using it. Touch Screen Some models are equipped with an optical touch screen. You can use your finger to manipulate icons, buttons, menu items, onscreen keyboard, and other items on the touch screen.
The optical touch screen has retro tapes on the left, right and bottom sides of the screen. The retro tapes are for identifying the point you touch by calculating the reflections of lights from the upper bezel. Please keep the LCD bezel and retro tapes clean. Otherwise, the touch screen may not function properly.
Keyboard Battery The Keyboard Battery icon shows the keyboard battery four status as below: : Good level : Low level : Critical level : Unknown If the computer resumes from hibernation/hybrid sleep mode without keyboard operation, the keyboard battery icon will show as unknown.In this case, you can press any key on the keyboard to update the battery icon to the current status.
You can configure the Function Keys Mode by selecting the "Special function mode" or "Standard F1-F12 mode". Please refer to the HW Setup section in Chapter 4, Utilities & Advanced Usage. Hot Key Cards The Hot Key Cards are normally hidden from view. To use the Hot Key Cards: 1. Start the TOSHIBA Flash Cards using the following methods: Press and hold the FN key (in Standard F1-F12 mode). 2. Press the associated Hot key (in Special function mode). Select the desired option.
User's Manual Special function mode Standard F1F12 mode Function F4 FN + F4 Launches Internet browser (by default)/ Bulletin Board/Eco utility/ Intel® WiDi or changes the active display device according to the setting in TOSHIBA Button Support utility. The provided options in TOSHIBA Button Support utility will be different depending on the models.
FN Sticky key You can use the TOSHIBA Accessibility Utility to make the FN key sticky, that is, you can press it once, release it, and then press an "F Number" key. To start the TOSHIBA Accessibility utility, click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> Accessibility.
Blu-ray™ Combo drive In addition to the above formats, Blu-ray™ Combo drive supports BD-ROM and BD-ROM DL. Blu-ray™ Writer drive In addition to the above formats, Blu-ray™ Writer drive supports BD-R, BDR DL, BD-RE and BD-RE DL. Blu-ray™ Writer drive BDXL™ In addition to the above formats, Blu-ray™ Writer drive BDXL™ supports BD-R TL, BD-R QL and BD-RE TL. Some types and formats of DVD-R DL and DVD+R DL discs may be unreadable.
3. Lay the disc in the disc tray with its label facing to the front of the computer. Figure 3-4 Inserting a disc 1 1. Laser lens When the disc tray is fully opened, the edge of the computer will cover the disc tray slightly. Therefore, you will need to turn the disc at an angle when you place it in the disc tray. After seating the disc, however, make sure it lies flat. Do not touch the laser lens or any portion of its surrounding casing as this could cause misalignment.
When the disc tray pops open slightly, wait a moment to make sure the disc has stopped spinning before pulling the disc tray fully open. 2. 3. The disc extends slightly over the sides of the disc tray so you can grasp it. Gently lift out the disc. Push the center of the disc tray to close it. Press gently until it locks into place. How to remove disc when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off.
DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once. Blu-ray™ discs BD-R, BD-R DL, BD-R TL and BD-R QL discs can be written only once. The recorded data cannot be erased or changed.. BD-RE, BD-RE DL and BD-RE TL discs can be recorded more than once. Writing discs The TOSHIBA Disc Creator and Corel Digital Studio are provided as writing software with this computer. Corel Digital Studio can be used to write files in video format. TOSHIBA Disc Creator can be used to write data.
Damage that may be caused by using third party equipment or software. Given the technological limitations of current optical disc writing drives, you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices. In view of this, it is good practice to make two or more copies of important data, in case of any undesired change or loss of the recorded contents.
DVD+RW: MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x and 8x speed media) DVD-RAM: (DVD Super Multi drive only) DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Panasonic Corporation (for 3x and 5x speed media) Hitachi Maxell, Ltd. (for 3x and 5x speed media) BD-R: Panasonic Corporation BD-R DL: Panasonic Corporation BD-RE: Panasonic Corporation BD-RE DL: Panasonic Corporation BD-R TL: TDK.
Do not perform any of the following actions: Change users in the Operating Systems. Operate the computer for any other function, including such tasks as using a mouse. Start a communication application. Apply impact or vibration to the computer. Install, remove or connect external devices, including such items as a memory media card, USB device or an optical digital device. Use the audio/video control button to reproduce music or voice. Open the optical disc drive.
You might not be able to use the "Disc Backup" function of TOSHIBA Disc Creator to back up a DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL or DVD+RW disc that was made with other software on a different optical media recorder. If you add data to a DVD-R, DVD-R DL, DVD+R or DVD+R DL disc that you have already recorded to, you might not be able to read the added data under some circumstances.
How to make a DVD-Video or a Blu-ray Disc™ Movie Simplified steps for making a DVD-Video or a Blu-ray Disc™ movie from adding video source: 1. 2. 3. 4. 5. 6. 7. 8. 9. Click Start -> All Programs -> Corel Digital Studio for TOSHIBA -> Corel Digital Studio for TOSHIBA to launch Corel Digital Studio. Insert a disc in optical disc drive. Find a source video and drag it onto Media Tray. Click Burn -> Video Disc. Select DVD or Blu-ray in Select disc. Select DVD-Video or BDMV in Project format.
Before recording the video to DVD or Blu-ray Disc™ When you record DVD disc or Blu-ray Disc™, please use only discs recommended by the Drive manufacturer. Do not set the working drive to a slow device like a USB1.1 hard disk drive or it will fail to write DVD or Blu-ray Disc™. Do not perform any of the following actions: Operate the computer for any other function, including using a mouse. Bump or cause vibration to the computer.
Unfinalized DVDs created on home DVD recorders may not be playable on the computer. Use DVD-Video discs with a region code which is either "the same as the factory default setting" (if applicable) or "ALL". Do not playback video while watching or recording television programs using other applications. Doing so may cause DVD-Video playback or television program recording errors.
Display Devices & Audio TOSHIBA VIDEO PLAYER will only run when "Colors" is set to "True Color (32 bit)". Click Start -> Control Panel -> Appearance and Personalization -> Display -> Adjust resolution, click "Advanced settings", select "Monitor" tab, set "colors" to "True color (32 bit)". If the DVD-Video image is not displayed on an external display or television, stop the TOSHIBA VIDEO PLAYER, and change the screen resolution.
The “TOSHIBA VIDEO PLAYER” is intended for playing DVD-Video, DVD-VR and video files and for viewing 2D home video content in 3D. The 3D playback of any video content not created by the user may require the permission of third parties, where such content is protected by copyright. The protection of intellectual property rights is essential for TOSHIBA. In this respect, TOSHIBA underlines that the Player should not be used in a manner infringing such rights.
2. When a DVD-Video disc is set in the DVD drive (for models with DVD drive), if the application selection screen appears, select Play DVD movie (using TOSHIBA VIDEO PLAYER) to launch the TOSHIBA VIDEO PLAYER. Select Start -> All Programs -> Midia & Entertainment -> TOSHIBA VIDEO PLAYER to start TOSHIBA VIDEO PLAYER. Operating TOSHIBA VIDEO PLAYER Notes on Using TOSHIBA VIDEO PLAYER. Screen display and available features may vary amongst DVD-Videos and scenes.
TOSHIBA Blu-ray Disc™ Player supports AACS (Advanced Access Control System) copy protection technology. Renewal of the AACS key integrated into this product is required for uninterrupted enjoyment of Blu-ray Disc™. An Internet connection is required for renewal. AACS key renewal is provided free of charge for 5 years after the purchase of this product, however renewal beyond 5 years is subject to conditions specified by the software provider, TOSHIBA Corporation.
The 3D playback function CANNOT be used to playback 2D video contents of Blu-ray Disc™ or AVCHD in 3D using real-time 2Dto3D conversion. The Player's 3D playback function is meant for only personal home use. Please take note that applicable copyright laws may prohibit the public display when you offer 3D viewing of third party video contents to unidentified personels or mass public. The 2Dto3D conversion function uses TOSHIBA's original algorithm to apply a 3D effect to your own 2D videos.
Depending on the system environment, 3D playback may only be used when the "Video Display Window" is at full-screen. 3D playback may not function when windowed. In order for the 3D playback to work on an external display/TV, you need a 3D enabled display/TV that has an HDCP compliant HDMI port. 3D video content can only be displayed on an external display which supports 3D features connected using HDMI with 3D.
If the menu is opened in the Display Area using the Control window's Top Menu or Menu buttons, mouse menu operations may not be able to be used. Open TOSHIBA Blu-ray Disc™ Player Manual TOSHIBA Blu-ray Disc™ Player features and instructions are explained in details in TOSHIBA Blu-ray Disc™ Player Manual. Use the following procedure to open TOSHIBA Blu-ray Disc™ Player Manual. Press F1 key when TOSHIBA Blu-ray Disc™ Player is launched and click the Help button.
Frequency Channel Selection of 5GHz for IEEE 802.11a or/and IEEE802.11n Frequency Channel Selection of 2.4GHz for IEEE 802.11b/g or/and IEEE802.
Network Operating System Microsoft Windows Networking Media Access Protocol CSMA/CA (Collision Avoidance) with Acknowledgment (ACK) Radio Characteristics Radio Characteristics of Wireless LAN module may vary according to: Country/region where the product was purchased Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.
Radio links You can easily establish links between two or more devices, with these links being maintained even if the devices are not within a line-of-sight of each other. Security Two advanced security mechanisms ensure a high level of security: Authentication prevents access to critical data and makes it impossible to falsify the origin of a message. Encryption prevents eavesdropping and maintains link privacy.
100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). This section describes how to connect/disconnect to a LAN. Do not install or remove a memory module while Wake-up on LAN is enabled. The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature. The Link speed (10/100/1000 megabits per second) changes automatically depending on the network conditions (connected device, cable or noise and so on).
2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. Figure 3-6 Connecting the LAN cable 2 1 1. LAN cable 3. 2. LAN jack Plug the other end of the cable into a LAN hub connector or router. Check with your LAN administrator and hardware or software vendor before using or configuring a network connection. Optional devices Optional devices can expand the computer's capabilities and its versatility.
Keep foreign objects out of the Memory media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the Memory media slot. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury. This Memory media slot supports the following memory media.
SD, SDHC and SDXC memory cards appear the same externally. However, the logo on memory cards is different, so pay careful attention to the logo when purchasing. The SD memory card logo is ( ). The SDHC memory card logo is ( The SDXC memory card logo is ( ). TM ). The maximum capacity of SD memory cards is 2GB. The maximum capacity of SDHC memory cards is 32GB. The maximum capacity of SDXC memory cards is 64GB.
Do not leave a card partially inserted in the slot. Press the card until you hear it click into place. Set the write-protect switch to the lock position, if you do not want to record data. Memory cards have a limited lifespan, so it is important to backup important data. Do not remove a card while read/write is in progress. About the write-protect The memory media cards have a function for protect.
Do not turn the computer off or switch to Sleep Mode or Hibernation Mode while files are being copied - doing so may cause data to be lost. Removing a memory media The following instructions apply to all types of supported media devices. To remove a memory media, follow the steps as detailed below: 1. 2. 3. 4. Open the Safely Remove Hardware and Eject Media icon on the Windows Taskbar. Point to memory media and click it. Press the memory media to partially extend it out of the computer.
Do not try to install or remove a memory module under the following conditions. a. The computer is turned on. b. The computer was shut down in either Sleep or Hibernation Mode. c. Wake-up on LAN is enabled. d. The wireless communication function is on. e. Sleep and Charge function is enabled. Be careful not to let screws or other foreign matter fall into the computer. It could cause malfunction or electric shock.
6. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 30 degree angle before holding it down until the latches on either side snap into place. Figure 3-10 Seating the memory module 1 3 2 1. Notch 2. Slot B 3. Slot A Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.
7. Seat the memory module cover in place and secure it with the screw. Take care to ensure that the memory module cover is firmly closed. Figure 3-11 Seating the memory module cover 1 2 1. Memory module cover 8. 2. Screw Turn the computer on and make sure the added memory is recognized - to confirmed it, Start -> Control Panel -> System and Security -> System icon. Removing a memory module To remove the memory module, follow the steps as detailed below: 1. 2. 3. 4. 5. 6.
7. Grasp the module by its edges and remove it from the computer. If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Figure 3-12 Removing the memory module 1 1 1. Latches 8.
Using the TV Tuner Antenna The quality of sounds and pictures greatly depends on the radio propagation conditions. When you use your computer in areas where the radio waves are weak, which results in poor radio receiving conditions, contact the dealer you purchased it from, or use a commercially available antenna booster. Please refer to the manual provided with the booster for details. Connecting the Cable This section describes how to connect the coaxial cable to your computer.
HDMI Out Some models are equipped with an HDMI out port. An HDMI display device can be connected to the HDMI out port on the computer. To connect the HDMI display device, follow the steps as detailed below: As the port operation of all HDMI (High-Definition Multimedia Interface) display devices have not been confirmed, some HDMI display devices may not function properly. Connecting the HDMI out port 1. 2. Plug one end of the HDMI cable into the HDMI input port of the HDMI display device.
When you change the display output device by hot key like Windows + P, the playback device may not switch automatically. In this case, in order to set the playback device to the same device as the display output device, please adjust the playback device manually by the following steps: 1. 2. 3. 4. 5. Click Start -> Control Panel -> Hardware and Sound -> Sound. In the Playback tab, select the playback device which you want to switch to. To use the internal speakers on your computer, select Speakers.
3. Plug the other end of the HDMI cable into the HDMI input port on your computer. Figure 3-15 Connecting the HDMI input port 1 2 1. HDMI input port 2. HDMI cable Security lock A security locks enable you to anchor your computer a desk or other heavy object in order to help prevent unauthorized removal or theft. The computer has a security lock slot on its back side into which you can attach one end of the security cable, while the other end attaches to a desk or similar object.
Memory Kit (DDR3-1600) can easily be installed in the computer. The available option memory depends on TOSHIBA authorization. Universal AC Adaptor If you frequently use your computer at more than one site, it may be convenient to purchase an additional AC adaptor to be kept at each site in order to remove the need to always carry the adaptor with you. Sound System This section describes some of the audio control functions.
SRS SRS Premium Sound 3D™ provides the ultimate audio and entertainment experience for all PC applications related to music, movies and games. Utilizing SRS’ revolutionary 3D audio technology, SRS Premium Sound 3D provides the most immersive and realistic listening experience unlike any solution ever offered for a two speaker playback environment.
Default Format You can change the sample rate and bit depth of sound. Video mode Video mode settings are configured via the Screen Resolution dialog. To open the Screen Resolution dialog, click Start -> Control Panel -> Appearance and Personalization -> Display -> Change display settings. If you are running some applications (for example a 3D application or video playback and so on), you may see some disturbance, flickering or frame dropping on your screen.
Turn off (shut down) the computer. Disconnect the AC adaptor and all peripherals before moving the computer. Do not pick up the computer by its display panel. Do not push the speaker mesh cover area which is below the display strongly, otherwise it may cause mesh deformation. Before carrying your computer, shut it down, disconnect the AC adaptor and allow it to cool down - a failure to follow this instruction may result in minor heat injury.
Chapter 4 Utilities & Advanced Usage This chapter describes the utilities and special features of this computer, and the advanced usage of some utilities. Utilities and Applications This section describes the pre-installed utilities that come with the computer and details how to start them. For further information on their operation, you may refer to each utility's online manual, help files or README.TXT file (if applicable).
Bluetooth Stack for Windows by Toshiba This software enables communication between the computer and external Bluetooth devices such as printers and mobile phones. Bluetooth functions cannot be used in models that do not have a Bluetooth module installed. TOSHIBA Assist TOSHIBA Assist is a graphical user interface that provides access to specific tools, utilities and applications that make the use and configuration of the computer easier.
TOSHIBA Blu-ray Disc™ Player This software is provided for playback of Blu-ray Disc™. It has an on-screen interface and functions. To start this utility, click Start -> All Programs -> TOSHIBA -> Media & Entertainment -> TOSHIBA Blu-ray Disc Player. This feature of TOSHIBA Blu-ray Disc™ Player is only available in some models.
TOSHIBA Media Controller This application allows you to control your music, pictures and videos by streaming content to any compatible device in your home. To access this utility, click Start -> All Programs -> TOSHIBA -> Media & Entertainment -> TOSHIBA Media Controller. For more information, please refer to the TOSHIBA Media Controller Help. TOSHIBA Resolution+ The plug-in lets you upconverts wmv and mp4 Plug-in for Windows videos on Windows Media Player.
For more information, please refer to the Help by selecting Options. The default window is Help window. CyberLink YouPaint CyberLink YouPaint is a painting program that lets children use a touch screen or a mouse to make creative digital drawings. Children can draw, use a stamp, trace and erase. Access this utility by one of the following ways: Start -> All Programs -> CyberLink -> CyberLink YouPaint. Click YouPaint icon under More Programs in CyberLink PowerCinema main window.
System automatic Sleep/Hibernation Mode *1 This feature automatically shuts down the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time. This can be specified in the Power Options. Power on password Two levels of password security, supervisor and user, are available to prevent unauthorized access to your computer. Instant security A specific hot key function automatically locks the system providing data security.
TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor application proactively monitors a number of system functions such as power consumption and system cooling, informing you of significant system conditions. This application recognizes the system and individual component serial numbers and will track specific activities related to their usage.
When there is a current overflow of the external devices connected to the compatible ports, USB bus power (DC5V) supply may be stopped for safety reasons. When Sleep and Charge function is enabled, the USB Wakeup function does not work for compatible ports. In that case, if there is a USB port that does not have the Sleep and Charge function, attach the mouse or keyboard to it. If all USB ports have the Sleep and Charge function, change to disable Sleep and Charge function.
Enabling Sleep and Charge This utility can be used to enable and disable the Sleep and Charge function. Select the Enable Sleep and Charge check box to enable this function for the compatible USB ports. The default state is disabled. Power supply mode settings Your computer has multiple charging modes so that many different USB devices can be supported for Sleep and Charge function. Auto Mode (Default) is suitable for a wide range of digital audio players.
This utility lets you do the following: Register or delete the Supervisor Password. Specify restrictions for general users. Starting the computer by password If you have already registered a password, there is one way to start the computer: Enter the password manually. The password is necessary only if the computer was shut down in boot mode, not in Hibernation or Sleep mode. To enter a password manually, follow the steps as detailed below: 1. Turn on the power as described in Chapter 1, Getting Started.
HW Setup window The HW Setup window contains a number of tabs (General, Password, Display, Boot Setting, Keyboard, USB and LAN) to allow specific functions of the computer to be configured. In addition there are also three buttons : OK, Cancel and Apply. OK Accepts your changes and closes the HW Setup window. Cancel Closes the window without accepting your changes. Apply Accepts all your changes without closing the HW Setup window. Some options shown in grey are possible to confirm their status.
2. 3. Click OK. The following message appears, allowing you to verify the password. Verify Password: If character strings match, the password is registered. Click OK. If they do not match, the following message appears. You must repeat from step 1. Entry Error!!! To delete a user password: 1. 2. 3. Select Not Registered to display the following prompt: Enter Password: Enter the currently registered password. The character string you enter is displayed as a string of asterisks. Click OK.
Boot Setting This function allows you to modify the boot settings. Boot Priority Options This tab allows you to set the priority for booting the computer. The Boot Priority Options setting window will be displayed. Click the up and down arrow buttons to adjust the priority. To change the boot drive, follow the steps below. 1. 2. Hold down F12 and boot the computer. when the TOSHIBA Leading Innovation >>> logo screen appears, release the F12 key.
USB Internal USB 3.0 controller Use this option to enable or disable the internal USB 3.0 controller. If Disabled is selected, the internal USB 3.0 port(s) on the computer will work as USB 2.0 port(s), which will save power. Enabled Enables the USB 3.0 controller. (Default) Disabled Disables the USB 3.0 controller. LAN Wake-up on LAN This feature lets the computer's power be turned on from shutdown when it receives a wake-up packet (Magic packet) from the LAN.
The collected information includes device operation time and number of actuations or status changes (i.e.: number of power button and FN key combination uses, AC adaptor, LCD, fan, HDD, sound volume, wireless communication functionalities, TOSHIBA Express Port Replicator and USB information), date of initial system use, and also computer and device usage (i.e.: power settings, CPU, memory, backlight illumination time, and temperatures for various devices).
If a TOSHIBA PC Health Monitor message is displayed. A message will be displayed if any changes which may interfere with the operation of the program are detected. Follow the instructions displayed on screen in the message. System Recovery There is a hidden partition allocated on the hard disk drive for the System Recovery Options in the event of a problem. You can also create recovery media and restore the system.
Be sure to close all other software programs except the Recovery Media Creator. Do not run software such as screen savers which can put a heavy load on the CPU. Operate the computer at full power. Do not use power-saving features. Do not write to the media when the virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background.
Restoring the pre-installed software from your created Recovery Media If the pre-installed files are damaged, you are able to either use the Recovery Media you have created or the hard disk drive recovery process to restore the computer to the state it was in when you originally received it. To perform this restoration, follow the steps below: When the sound mute feature has been activated, be sure to disable this to allow sounds to be heard before starting the restore process.
Restoring the pre-installed software from the Recovery hard disk drive A portion of the total hard disk drive space is configured as a hidden recovery partition. This partition stores files which can be used to restore pre-installed software in the event of a problem. If you subsequently set up your hard disk drive again, do not change, delete or add partitions in a manner other than specified in the manual, otherwise you may find that space for the required software is not available.
Chapter 5 Power and Power-Up Modes The computer's power resources include the computer, wireless keyboard and wireless mouse. The computer is supplied with the AC adapter while the wireless keyboard and mouse are supplied with AAA batteries.This chapter provides details on making the most effective use of these resources, and includes information on the different power-up modes. Monitoring of power condition As shown in the below table, the Power indicator alerts you to the computer’s operating capability.
You can change the Real Time Clock settings in the BIOS setup utility. To access it, press and hold the F2 key, and then turn on the computer - the BIOS setup utility will load. Please refer to Chapter 6 Troubleshooting for further information. Batteries for the wireless keyboard and mouse The wireless keyboard and mouse equipped with the computer use the normal AAA batteries. When batteries run out, you need replace them in time.
Chapter 6 Troubleshooting TOSHIBA have designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place.
Check all cables to ensure they are correctly and firmly attached to the computer - loose cables can cause signal errors. Inspect all connecting cables for loose wires and all connectors for loose pins. Check that your disc media is correctly loaded Always try to make detailed notes of your observations and keep them in a permanent error log - this will help you to describe your problems to TOSHIBA Support. In addition, if a problem recurs, the log you have made will help to identify the problem faster.
Hardware If you cannot find a software problem, you should then check the setup and configuration of your hardware. First run through the items in the preliminary checklist as described previously then, if you still cannot correct the problem, try to identify the source - the next section provides checklists for individual components and peripherals.
indicator glows amber, the computer is connected to a live external power source. Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.
Problem Procedure AC adaptor doesn’t power the computer (Power indicator does not glow white) Check the connections to make sure that the power cord/adaptor is firmly connected to the computer and a working power outlet. Check the condition of the cord and terminals. If the cord is frayed or damaged it should be replaced, while if the terminals are soiled, they should be cleaned with a clean cotton cloth. If the AC adaptor still does not power the computer, you should contact TOSHIBA Support.
Internal display panel Apparent computer's display panel problems may be related to the computer's setup and configuration - please refer to the HW Setup section in Chapter 4, Utilities & Advanced Usage, for further information. Problem Procedure No display Press the hot key to adjust the display priority, and to make sure it is not set for output to an external monitor. Markings appear on the computer's display panel. These marks may have come from contact with fingers.
Problem Procedure You cannot access a Make sure the drive’s disc tray is securely closed. CD/DVD/Blu-ray Press gently until it clicks into place. Disc™ in the drive Open the disc tray and make sure the disc is properly seated. It should lie flat with the label facing up. A foreign object in the disc tray could block laser light from reading the disc. Make sure there is no obstruction. Remove any foreign object. Check whether the disc is dirty.
Wireless mouse Problem Procedure On-screen pointer does not respond to mouse operation In this instance the system might be busy - Try moving the mouse again after waiting a short while. Pair the wireless mouse again. Refer to the Pairing the keyboard/mouse section in Chapter 1 for details on pairing. Double-clicking does In this instance, you should initially try changing not work the double-click speed setting within the Mouse Control utility. 1. 2. 3.
Problem Procedure USB device does not Remove the USB device from the computer and work then reconnect it to a free port in order to ensure it is firmly attached. Ensure that any required USB device drivers are properly installed - to achieve this you should refer to both the device documentation and the operating system documentation. Sleep and Charge function For more information and settings, please refer to the Using the TOSHIBA Sleep Utility section in Chapter 4, Utilities & Advanced Usage.
Problem Procedure External devices connected to the compatible ports do not work when connected to a compatible port. Some external devices may not work when connected to a compatible port if the Sleep and Charge function is enabled. The "USB Wakeup function" does not work. When Sleep and Charge function is enabled, the "USB WakeUp" function does not work for ports that support the Sleep and Charge function. Reconnect the external device after turning the computer ON.
Problem Procedure Annoying sound is heard In this instance you may be experiencing feedback from either the internal microphone or an external microphone connected to the computer - please refer to Sound System in Chapter 3, Operating Basics for further information. Volume cannot be adjusted during Windows start up or shut down. If you are still unable to resolve the problem, contact TOSHIBA Support.
Problem Procedure No display Try adjusting the contrast and brightness controls on the external monitor. Press the hot key in order to change the display priority and ensure that it is not set for the internal display only. Check to see if the external monitor is connected. When the external monitor is set as the primary display device in extended desktop mode, it will not display when the computer wakes up from Sleep Mode if the external monitor has been disconnected while in Sleep Mode.
Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 3, Operating Basics. Problem Procedure Cannot access Wireless LAN Make sure the computer's Wireless communication function is on. If problems persist, contact your LAN administrator. Bluetooth For further information on Bluetooth wireless communication, please refer to Chapter 3, Operating Basics.
If a problem occurs when you are running software applications, consult the software documentation for troubleshooting suggestions and consider calling the software company's technical support department for assistance. Consult the reseller or dealer from where you purchased your computer and/or software - they are your best resource for current information and support.
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size 561.4 (w) x 190 (d) x 439 (h) millimeters (not including parts that extend beyond the main body).
Appendix B AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Certification agencies China: CQC U.S. and Canada: UL listed and CSA certified No.
The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia, Europe and China.
Appendix C Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. Non-applicable Icons Certain computer chassis are designed to accommodate all possible configurations for an entire product series. Therefore, please be aware that your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis. CPU Central Processing Unit (CPU) Performance Legal Footnotes.
Contact TOSHIBA technical service and support, refer to TOSHIBA support section in Chapter 6, Troubleshooting for more information. 64-Bit Computing 64-bit processors are designed to take advantage of 32 and 64 bit computing.
such as Microsoft Operating System and/or pre-installed software applications, or media content. Actual formatted capacity may vary. LCD Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Maximum brightness is only available when operating in AC power mode.
Appendix D Information for Wireless Devices Wireless LAN Interoperability The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum (DSSS) /Orthogonal Frequency Division Multiplexing (OFDM) radio technology, and is compliant to: The IEEE 802.11 Standard on Wireless LANs (Revision a/b/g/n or b/g/ n), as defined and approved by the Institute of Electrical and Electronics Engineers. The Wireless Fidelity (Wi-Fi®) certification as defined by the Wi-Fi Alliance®.
If you should experience any such problem, immediately turn off either one of your Bluetooth or Wireless LAN. Please visit http://www.pc.support.global.toshiba.com, if you have any questions about using Wireless LAN or Bluetooth Card from TOSHIBA. In Europe visit http://www.toshiba-europe.com/computers/tnt/bluetooth.htm Your Bluetooth product is not compatible with devices using Bluetooth Version 1.
Europe Restrictions for Use of 2400.0-2483.5MHz Frequencies in Europe France: Outdoor use limited to 10mW e.i.r.p. within the band 2454-2483.5MHz Military Radiolocation use.Refarming of the 2.4GHz band has been ongoing in recent years to allow current relaxed regulation Full implementation planned 2012. Italy: - For private use, a general authorization is required if WAS/ RLAN’s are used outside own premises. For public use, a general authorization is required.
Russian Federation: Limited e.i.r.p 100mW. Permitted to use only for indoor applications, closed industrial and warehouse areas, and on board aircraft. 1. 2. Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight. Permitted to use for public wireless access local networks on board aircraft during a flight at the altitude not less than 3000m.
check the current channel of operation. If operation is occurring outside of the allowable frequencies for outdoor use, as listed above, the user must contact the applicable national spectrum regulator to request a license for outdoor operation. Canada - Industry Canada (IC) This device complies with RSS 210 of Industry Canada.
Article 14 The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; If found, the user shall cease operating immediately until no interference is achieved. The said legal communications means radio communications is operated in compliance with the Telecommunications Act. The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices.
4. 5. 4 : The interference range of this equipment is less than 40m. : This equipment uses a frequency bandwidth from 2,400MHz to 2,483.5MHz. It is possible to avoid the band of mobile object identification systems. 3. Indication for Bluetooth The indication shown below appears on this equipment. 1. 2. 3. 4. 2.4 : This equipment uses a frequency of 2.4 GHz. FH : This equipment uses FH-SS modulation. 1 : The interference range of this equipment is less than 10 m.
Intel 2200BNHMW 802.11b/g/n Wireless LAN The Name of the radio equipment: 2200BNHMW DSP Research, Inc. Approval Number: D111209003 The following restrictions apply: Do not disassemble or modify the device. Do not install the embedded wireless module into other device. When using the wireless device in any country or region, refer to the section Radio approvals for wireless devices in the online manual.
Index A DVD Super Multi drive using writing AC adaptor additional 3-42 connecting 1-3 DC IN 19V jack 2-9 E Equipment checklist 1-1 ASCII characters 3-6 External monitor problems 6-11 B Battery real time clock 2-17, 5-1 F Function keys 3-3 Battery pack additional 5-1 Bluetooth Bluetooth Stack for Windows by Toshiba 4-2 problems 6-13 G Graphics controller 2-17 H Hard disk drive automatic power off 4-5 Boot Priority 4-13 C HDMI out port 2-8 Cleaning the computer 3-44 Cooling vents 2-7 Heat dispers
K power on 4-6 Starting the computer by 4-10 Supervisor 4-9 user 4-9 Keyboard FN Sticky key 3-6 Function keys F1...
Recovery Media 4-18, 4-19 Restarting the computer 1-11 W Wireless communication 3-24 S SD/SDHC/SDXC Card formatting 3-31 note 3-30 Wireless LAN problems 6-13 Security lock 3-41 Sleep Mode setting 1-8 System automatic 4-6 Sound system problems 6-10 T TOSHIBA Assist 4-2 TOSHIBA Disc Creator 3-13, 4-2 TOSHIBA HDD/SSD Alert Utility 4-2 TOSHIBA PC Diagnostic Tool 4-1 TV Tuner jack U USB device problems 6-8 V Video mode 3-44 Video RAM 2-17 User's Manual Index-3
