Introduction 2 DIGITAL VIDEO COMBINATION FLAT COLOR TELEVISION AND VIDEO CASSETTE RECORDER / DVD VIDEO PLAYER Connections Basic setup TV operation MW20FN3/R MW24FN3/R Playback (VCR) Recording (VCR) 14 19 23 35 40 OWNER’S MANUAL Other functions (VCR) 45 Basic playback (DVD) 49 Advanced playback (DVD) 52 Function setup (DVD) 56 Others ©2003 Toshiba Corporation This device does not tape-record copy protected DVD Video Discs.
Introduction IMPORTANT SAFEGUARDS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN REDUCE THE RISK OF ELECTRIC CAUTION: TO SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
IMPORTANT SAFEGUARDS 1. Introduction READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated. 2. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference. 3. HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to. 4. FOLLOW INSTRUCTIONS All operating and use instructions should be followed. 5. CLEANING Unplug this unit from the wall outlet before cleaning.
Introduction IMPORTANT SAFEGUARDS 14. POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal. 15.
IMPORTANT SAFEGUARDS / Power Source 27. NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
Introduction Precautions Notes on handling When shipping the unit, the original shipping carton and packing materials come in handy. For maximum protection, repack the unit as it was originally packed at the factory. Do not use volatile liquids, such as insect spray, near the unit. Do not leave rubber or plastic products in contact with the unit for a long time. They will leave marks on the finish. The top and rear panels of the unit may become warm after a long period of use. This is not a malfunction.
Notes on discs Structure of disc contents Do not touch the playback side of the disc. Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. Video CDs and Audio CDs are divided into tracks. Introduction On handling discs DVD video disc DVD video disc Title 1 Chapter 1 Title 2 Chapter 2 Chapter 1 Chapter 2 Chapter 3 Playback side Do not attach paper or tape to discs.
Introduction Notes on discs (continued) About this owner’s manual This owner’s manual explains the basic instructions of this unit. Some DVD video discs are produced in a manner that allows specific or limited operation during playback. As such, the unit may not respond to all operating commands. This is not a defect in the unit. Refer to instruction notes of discs. Playable discs This unit can play the following discs. Disc Mark Contents Disc Size Maximum playback time Approx.
Contents Basic playback (DVD) IMPORTANT SAFEGUARDS .......................... 2 Power source ................................................... 5 Precautions ...................................................... 6 Notes on discs.................................................. 7 Contents ........................................................... 9 Identification of Controls ................................. 10 Preparation ..................................................... 49 Playback procedure ....
Introduction Identification of Controls See the page in for details.
TV/VCR operation status While watching TV Introduction Press DISPLAY to display the information on the screen. To cancel the display, press DISPLAY again.
Introduction Identification of Controls (continued) The instructions in this manual describe the functions on the remote control. See the page in for details.
Introduction Inserting Batteries 1 Slide the battery compartment cover in the direction of the arrow. 2 Install two “AAA” batteries (supplied), paying attention to the polarity diagram in the battery compartment. 3 Replace the compartment cover. Battery precautions: The precautions below should be followed when using batteries in this device: 1. Use only the size and type of batteries specified. 2.
Connections Antenna connections If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If you are using a cable TV service (CATV), see page 15 for Cable TV connections. Combination VHF/UHF Antenna (Single 75 ohm Cable or 300 ohm Twin-lead Wire) Connect the 75 ohm Cable from the Combination VHF/UHF Antenna to the Antenna Jack.
Cable TV Connections This unit has an extended tuning range and can tune most cable channels without using a Cable TV Converter box. Some cable companies offer “premium pay channels” in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable company.
Connections Connecting to optional equipment Before connecting the unit to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections. You can enjoy the TV game, camcorder or high quality dynamic sounds of DVD video discs or audio CDs by connecting the unit to optional audio equipment. Connecting a camcorder or a TV game Select “LINE 2” using the INPUT SELECT button.
: Front speaker : Rear speaker : Sub woofer : Center speaker : Signal flow Connecting to an amplifier equipped with a Dolby Digital decoder Manufactured under license from Dolby Laboratories. “Dolby” “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works. ©1992-1997 Dolby Laboratories. All rights reserved.
Connections Warning: When playing DTS-encoded discs (unit), excessive noise may be output from the analog stereo jacks. To avoid possible damage to the audio system, you should take proper precautions when the ANALOG AUDIO OUT (L/R) jacks of the unit are connected to an amplification system. To enjoy DTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must be connected to the BITSTREAM/PCM AUDIO OUT jack of the unit.
Basic setup TV/VCR Setting the language POWER This unit can display the on screen language in English, Spanish or French. Language selection (step 3) will automatically appear on the screen when you press MENU initially. Select the language you prefer first, then proceed with the other menu options. 1-3 1,4 1-3 Setting the language • Press POWER to turn on the unit. • Press TV/VCR to select the TV/VCR mode. 1 Press MENU. Press or to select “SYSTEM SETUP”, then press ENTER. tion 56 .
Basic setup Clock setting POWER DISPLAY The Auto Clock function will automatically set the built-in clock (Month, Day, Year and Time) when the unit is connected to an Antenna or Cable system and it is turned off. As the unit searches for a receivable station in your area and it receives a broadcast signal for Auto Clock, the Auto Clock needs several minutes to set itself. 2,3 1,5 2,4 Auto Clock setting To set Auto Clock to OFF Preparation: When shipped from factory the AUTO CLOCK is set to “ON”.
To set standard time To set daylight saving time In the rare event that you live within broadcast range of two stations in two different time zones, the unit may recognize the wrong station for the Auto Clock set. To correct the situation: You can set the Daylight saving time automatically or manually. 1 1 Press MENU. MENU SETUP Press MENU. Press or to select “SYSTEM SETUP”, then press ENTER.
Basic setup Clock setting (continued) You must set the date and time manually for Timer Recordings, ON/OFF Timer and Daylight Saving Time if the Auto Clock process did not set them correctly. 2-4 1 2-4 Manual clock setting EXAMPLE: Setting the clock to “8:30 AM”, 29th. (WED) October, 2003. 1 6 After setting the clock, date and time starts functioning automatically. Press MENU. 8 : 30 AM WED MENU SETUP 2 Press or to select the “SYSTEM SETUP”, then press ENTER.
TV operation 2 1 5 3 TV Operation TV operation 1 5 To turn on the unit, press POWER. POWER Press TV/VCR to select the TV/VCR mode. 3 Adjust the volume level by pressing VOLUME ▲ or ▼. The volume level will be indicated on the screen by green bars. As the volume level increases, so do the VOLUME number of bars. If the volume decreases, the number of green bars also decreases. TV/VCR When TV/CATV menu is in the TV position, all channels can be instantly selected by using two buttons.
TV operation TV Operation (continued) CHANNEL / MUTE CHANNEL RETURN SLEEP Sleep Mute To set the unit to turn off after a preset amount of time, press SLEEP on the remote control. The clock will count down 10 minutes for each press of SLEEP (120, 110, ...10, 0). After the sleep time is programmed, the display will appear briefly every ten minutes to remind you that the sleep timer is operating. To confirm the sleep timer setting, press SLEEP and the remaining time will be display for a few seconds.
CLOSED CAPTION Closed Captions Press this button to switch between normal TV and the two closed caption modes (captions and full screen text). Closed captioning will display text on the screen for hearing impaired viewers. SKIP CAPTION CH 1 WHAT IS CLOSED CAPTIONING? This television has the capability to decode and display Closed Captioned television programs. Closed Captioning will display text on the screen for hearing impaired viewers or it will translate and display text in another language.
TV operation Tuner setting This unit is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the unit’s memory. In addition to normal VHF and UHF channels, this unit can receive up to 113 Cable TV channels. To use this unit with an antenna, set the TV/CATV menu option to the TV mode. When shipped from the factory, this menu option is in the CATV mode.
Direct channel selection 1,5 1,2,4 1-3 To ADD/DELETE channels 1 Press MENU. Press then press ENTER. or to select “CH SETUP”, 4 MENU SETUP ENTER 〈 / /ENTER/MENU〉 ENTER 2 Press or to select “ADD/DELETE”, then press ENTER. DEL TV operation MENU TIMER REC SET TV SETUP CH SETUP AUTO REPEAT ON OFF SYSTEM SETUP Press ENTER to select “ADD” or “DEL”. If you select an unmemorized channel, the Channel indication will be red.
TV operation Setting the V-Chip NUMBER buttons An age limitation can be set to forbid children to watch programs according to “TV RATING” and “MOVIE RATING” level set. To use the V-Chip function, you must register a password. / MENU ENTER To register password To set the V-chip 1 1 Press MENU. Press then press ENTER. or to select “TV SETUP”, MENU In “V-CHIP SET” menu, press or “TV RATING”, then press ENTER.
/ MENU ENTER 4 Press or to select desired rating, then press ENTER. ENTER 〈 / /ENTER/MENU〉 OFF G PG PG-13 : : : : R : NC-17 : X : 5 Press MOVIE RATING is not set All ages Parental guidance Parental guidance less than 13 years old Under 17 years old Parental guidance suggested 17 years old and above Adult only or Press MENU repeatedly until the MENU screen is cleared. MENU SETUP Note: The V-Chip function is activated only on programs and tapes that have the rating signal.
TV operation Setting the V-Chip (continued) 3,5,6 1,2,4 1,7 1-6 To Change password 1 Press MENU. Press or then press ENTER. to select “TV SETUP”, 5 Enter the new password using the Number buttons (0-9), then press ENTER.
To set the on timer This feature allows you to have the unit automatically turn on at a predetermined time. If you program the ON TIMER once, the unit will turn on on the programmed day (daily/weekly) at the same time to the same channel. 1,7 PROGRAM 1-6 1-6 To set the on timer EXAMPLE: Turning on the TV to channel 12 at 7:00 AM, MONDAY-FRIDAY. MENU or Set the desired minute, channel and daily or weekly timer date as in step 4.
TV operation To set the off timer This feature allows you to have the unit turn off automatically at a predetermined time. If you program the OFF TIMER once, the unit will automatically turn off at the same time everyday. 1,7 1-6 1-6 To set the off timer EXAMPLE: Turning off the TV at 11:30 PM. 1 5 Press MENU. Press or to select “TV SETUP”, then press ENTER. MENU You can also select ON/OFF TIMER by pressing PROGRAM twice. Press or to set the desired minute, then press ENTER.
Picture control adjustment Picture controls are factory preset but you can adjust them individually as follows: 1 1-2 CANCEL Picture control adjustment 1 To display the picture adjustment screen, press MENU. Press or to select “TV SETUP”, then press ENTER. MENU TIMER REC SET TV SETUP CH SETUP AUTO REPEAT ON OFF SYSTEM SETUP SETUP ENTER Press ENTER until “COLOR” appears on the screen, then press or to adjust the color intensity of the picture.
TV operation Sound control adjustment 1 1-3 CANCEL Sound control adjustment 1 To display the sound adjustment screen, press MENU. Press or to select “TV SETUP”, then press ENTER. MENU 〈 / /ENTER/MENU〉 ENTER 2 or to adjust the setting.
Playback (VCR) Loading and unloading a cassette tape Use only video cassette tapes marked . Loading Push the center of the tape until it is automatically inserted. Insert the cassette tape with its labeled side facing up and the erase prevention tab positioned at your left. An inverted cassette tape cannot be inserted. Erase prevention tab Automatic power ON When you insert a cassette tape the unit power will turn ON automatically.
Playback (VCR) Cassette tape playback To play a prerecorded tape. REV PLAY AUDIO PHONES VIDEO L/MONO R REW STOP/EJECT PLAY FF REC/OTR CHANNEL OPEN/CLOSE POWER VOLUME SKIP STOP PLAY SKIP POWER REC/OTR TIMER REC LINE IN 2 FWD STOP REW FF PLAY STOP/EJECT Playback Rewind or forward the tape 1 Load a prerecorded tape: Preparation: (When loading a cassette tape without the erase prevention tab, playback will start automatically). • Press TV/VCR to select the TV/VCR mode.
Special playback CM SKIP REV SLOW PLAY FWD PAUSE/STILL D.TRACKING TRK +/– Picture search Digital tracking controls Reverse picture search function Press REV once or twice during the playback. Forward picture search function Press FWD once or twice during the playback. To return to playback, press PLAY. When a tape is played, the Digital Auto Tracking system automatically adjusts the tracking to obtain the best possible picture.
Playback (VCR) Convenient function MENU DISPLAY REC PLAY COUNTER RESET ENTER Repeat playback Using the real time tape counter The entire video tape will be played until its end. The tape will automatically rewind to the beginning and the playback will be repeated. The On-Screen Real Time Tape Counter shows the tape running time in Hours, Minutes and Seconds. You can easily determine how long the tape has been running or how much time is left on the tape. 1 1 Press MENU. Press REPEAT”.
1 3 2 3 4 5 Video head cleaning The zero return function provides a convenient method of rapidly returning to the starting point of recording or playback. The starting point can be indexed for any location on the tape by pressing COUNTER RESET and ZERO RETURN. Video head clogging The video heads are the means by which the unit reads the picture from the tape during playback. In the unlikely event that the heads become dirty enough to be clogged, no picture will be played back.
Recording (VCR) TV/VCR 4 Recording a TV program Recording and viewing the same TV program. 5 2 Recording a TV program 1 Load a cassette tape with the erase prevention tab intact. The unit will automatically turn on. 5 Press both REC at the same time. “ ” will appear on the screen for about 4 seconds and the REC/OTR indicator on the front panel will light. CH 110 REC 2 Press SP/SLP to select the desired tape speed SP or SLP.
STOP PAUSE/STILL To stop recording Press STOP to stop recording. “ ” will appear on screen for about 4 seconds. Auto Rewind feature This VCR will automatically rewind the tape when the tape has ended (except during OTR and timer recording). It will also eject the tape. Note: If the erase prevention tab is removed, the tape will eject when both the REC buttons are pressed for recording. STOP To stop recording temporarily Recording (VCR) Press PAUSE/STILL to avoid recording unwanted material.
Recording (VCR) One-touch Timer Recording (OTR) 4 The One-touch Timer Recording feature provides a simple and convenient way to make a timed recording. 5 STOP 2 One-touch Timer Recording (OTR) Example: One-touch Timer Recording for 30 minutes. 1 2 Load a cassette tape with the erase prevention tab intact. 5 The unit will automatically turn on. Press both REC at the same time to begin recording. Press the buttons again to stop recording after 30 minutes.
TV/VCR Timer recording Timer recording can be programmed on-screen with the remote control. The built-in timer allows automatic unattended recording of up to 8 programs within 1 month. 2-3,5 6 1 1-3,5 CANCEL Timer recording Preparation: • Press TV/VCR to select the TV/VCR mode. • Load a cassette tape with the erase prevention tab intact. • Check the time and date are correct 22 . Example: Program a timer recording for 23rd day, channel 125 (CATV), 7:00 - 9:30 PM (Tape speed : SLP).
Recording (VCR) Timer recording (continued) PROGRAM ENTER CANCEL To set daily/weekly timer To confirm the settings Weekly (e.g. WKL-TUE: each Tuesday) or daily (e.g. MON-SAT: Monday to Saturday) Timer recording Follow the procedure of timer recording on the previous page. At picture 3 press or repeatedly until the desired setting appears. Then press ENTER. Press PROGRAM once. The TV screen displays the timer program list. Press PROGRAM again. The TV screen displays the ON/OFF timer setting.
Other functions (VCR) Setting the surround sound/ Setting the stable sound 1-2 1-2 1-2 Setting the surround sound Setting the stable sound The surround sound feature expands the audio listening field wider and deeper to create exceptional sound quality from the TV’s speakers. The stable sound feature limits the highest volume level to prevent extreme changes in volume when the signal source is changed. 1 1 Press MENU. Press or then press ENTER.
Other functions (VCR) Second Audio Program (SAP)/ Stereo recording and playback AUDIO SELECT 1-2 1-2 1-2 Second Audio Program (SAP) Stereo recording and playback Your unit is fitted with a SAP broadcast system which enables you to switch to a Second Audio Program when viewing a selected channel. This function applies only when the program is broadcast in multi-languages through the SAP broadcast system. The VHS Hi-Fi audio system permits high fidelity recording of MTS STEREO TV broadcasts.
TV/VCR Duplicating a video tape If you connect the unit to another VCR or Camcorder, you can duplicate a previously recorded tape. Make all connections before turning on the power. 3 3 2 1 Duplicating a video tape Preparation: • Press TV/VCR to select the TV/VCR mode. • Load a cassette tape with the erase prevention tab intact. • Load a previously recorded tape into the playback Connection with second video recorder • Select “LINE1” on step 2. Playback VCR VCR or Camcorder.
TV/VCR 2 Recording a DVD/CD disc You can record disc material in DVD, Audio CD, etc. onto a video tape with this unit. 4 3 5 1 Duplicating a DVD or CD disc Preparation: • Press TV/VCR to select the TV/VCR mode. • Load a cassette tape with the erase prevention tab intact. • Load a DVD/CD disc. 1 Notes: • You may not record the beginning of the disc, so start to playback the disc, then start to record. • You cannot record the disc with copy guard function.
Basic playback (DVD) 3 2 Preparation The following pages describe the setup/operation in DVD mode. DVD VCD CD Preparation 1 Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet. 2 Press POWER on the unit or on the remote control to turn on the unit. If the AC cord plug is plugged in for the first time, wait for about 5 seconds before pressing POWER. POWER • The POWER indicator will light. • Every time you press POWER, the unit starts from TV mode.
Basic playback (DVD) 7 Playback procedure 3,6 6,7 AUDIO PHONES VIDEO L/MONO R REW STOP/EJECT PLAY FF REC/OTR CHANNEL OPEN/CLOSE POWER VOLUME SKIP STOP PLAY SKIP POWER REC/OTR TIMER REC LINE IN 2 5 OPEN/CLOSE 4 DVD VCD CD 1 Playback procedure Press OPEN/CLOSE on the unit. 5 The disc tray will open. Press ENTER. Title is selected and play commences. ENTER OPEN/CLOSE 6 2 Place a disc onto the tray.
Special playback Note: There may be a slight delay between when you press the button and the function activating. DVD VCD CD Fast forward playback Press FWD during normal playback. FWD PLAY DVD VCD CD Press REV during normal playback. PLAY Each press of REV will increase the speed of the search , , , . To resume normal playback, press PLAY. Frame advance Press PAUSE/STILL during still playback. Each press of FWD will increase the speed of the search , , , . To resume normal playback, press PLAY.
Advanced playback (DVD) DVD Number button (0-9) Zooming/Locating desired scene JUMP ZOOM ENTER CANCEL DVD VCD Zooming This unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the frame. 1 Press DVD to select DVD mode. Press ZOOM during playback. The center part of the image will be zoomed in. DVD Each press of ZOOM will change the ZOOM 1 (x 2), 2 (x 3) and 3 (x 4). INPUT SELECT ZOOM 2 Press / / frame.
Repeat, Random and Program playback/Repeat A-B Number buttons (0-9) PLAY STOP CANCEL REPEAT A-B ENTER PLAY MODE DVD VCD CD Repeat, Random and Program playback Press PLAY MODE during playback or stop mode. TRK - Each time you press PLAY MODE, playback mode changes as follows. *Program menu Use number buttons (0–9) to enter the track’s number you want to program, then press ENTER.
Advanced playback (DVD) Changing soundtrack language/ Subtitles AUDIO SELECT SUBTITLE DVD Changing soundtrack language You can select the language when you play a multilingual disc. 1 Press AUDIO SELECT during playback. AUDIO SELECT The current soundtrack language will appear. 2/8 Fra Dolby Digital 2 Press AUDIO SELECT repeatedly until the desired language is selected. AUDIO SELECT 1/8 Eng Dolby Digital In case of video CD playback Audio type changes as follows each time you press AUDIO SELECT.
Changing angles/Title selection/DVD menu PLAY ENTER ANGLE TOP MENU DVD MENU DVD Changing Angles When playing back a disc recorded with multi-angle facility, you can change the view angle. 1 Press ANGLE during playback. The current angle will appear. 2 Press ANGLE repeatedly until the desired angle is selected. COUNTER RESET COUNTER RESET 1/9 ANGLE ANGLE Note: Depending on the DVD, you may not be able to change the angles even if multi-angles are recorded on the DVD.
Function setup (DVD) 1 Setting language You can change the default settings to customise performance to your preference. 1,5 RETURN 1-4 DVD 1 Setting Language Press DVD to select DVD mode. Press SETUP in the stop mode. Press or to select “Language”, then press or ENTER. DVD MENU SETUP 2 Press press Press SETUP to remove the Menu screen.
1 Setting the aspect ratio of TV screen/ Setting on screen display You can select the aspect ratio for your TV. On screen display can be switched on or off when you press the buttons. 1,4 RETURN 1-3 DVD 1 Setting the aspect ratio of TV screen Press DVD to select DVD mode. Press SETUP in the stop mode or No Disc. Press or to select “Picture”, then press or ENTER. DVD DVD 1 MENU Language Picture Sound Parental ENTER Press DVD to select DVD mode. Press SETUP in the stop mode or No Disc.
Function setup (DVD) 1 Dynamic Range Control DRC (Dynamic Range Control) enables you to control the dynamic range so as to achieve a suitable sound for your equipment. 1,4 RETURN ENTER DVD 1 Dynamic Range Control Press DVD to select DVD mode. Press SETUP in the stop mode. Press DVD MENU or to select “Sound”. Main Menu Language Picture Sound Parental SETUP ENTER /Enter/Setup/Return 2 Press or ENTER to select “DRC”.
1 Parental control setting 5 Some discs are specified not suitable for children. Such discs can be limited not to play back with the unit. 1,7 RETURN 1-4,6 5 DVD 1 Parental control setting Press DVD to select DVD mode. Press SETUP in the stop mode. Press or to select “Parental”, or ENTER. then press DVD 5 MENU Main Menu Language Picture Sound Parental SETUP ENTER Press number buttons (0–9) for the password. Don’t forget the password. 1 2 3 4 5 6 7 8 9 2 or press or ENTER.
Function setup (DVD) DVD To change the parental level 3,8 RETURN 1,10 ENTER CANCEL To change the parental level DVD 1 Press DVD to select DVD mode. Press SETUP in the stop mode or No Disc. Press “Parental”, then press or to select 5 or ENTER. Press or to select “Parental Level”. Then press or ENTER. The Parental Level screen is displayed.
To change the parental level (continued)/Temporary disabling of rating level by DVD disc 1 3 2,3 9 Press ENTER. The parental level is now changed and locked. 10 Press SETUP to remove the parental control screen. MENU Parental Password Parental Level ENTER On 8 /Enter/Setup/Return SETUP Note: Do not forget the password. If you forget the password, contact the dealer that you purchased the unit from. • If you want to return to the previous menu, press or RETURN.
Others Before calling service personnel Check the following guide for the possible cause of a problem before contacting service. Symptoms and correction SYMPTOMS CAUSE POSSIBLE SOLUTIONS PAGE POWER The AC power cord is not connected. No power. Although the power is on, the unit does not operate. Cassette or disc is not inserted. The TIMER REC buttons are depressed. Connect the AC power cord to the AC outlet. Insert a video cassette or disc. Press the TIMER REC buttons.
SYMPTOMS CAUSE POSSIBLE SOLUTIONS PAGE VCR TV recording does not work. Timer recording does not work. Noise bars appear on the screen. The video cassette's erase prevention tab is broken off. The time is not set correctly. The recording start/end time is not set correctly. The TIMER REC buttons have not been pressed at the same time (the TIMER REC indicator is not lit). Tape is old or worn. Tracking adjustment is beyond range of automatic tracking circuit. Video heads are dirty.
Others Reception disturbances Most types of television interference can be remedied by adjusting the height and position of the VHF/UHF antenna. Outdoor antennas are recommended for best results. The most common types of television interference are shown below. If one of these symptoms appear when the unit is connected to a Cable TV system, the disturbance may be caused by the local Cable TV company broadcast. IGNITION Black spots or horizontal streaks may appear, the picture may flutter or drift.
Language code list Enter the appropriate code number for the initial settings “Menu”, “Audio” and/or “Subtitle” (see page 56).
Others Specifications General / input / output / supplied accessories GENERAL Picture Tube Speaker Audio Output Power Power supply Power consumption Weight Dimensions Operating conditions Tuner Antenna input/output Color system Video head Audio track Hi-Fi frequency response Hi-Fi dynamic range F.
Limited warranty Toshiba America Consumer Products, Inc. (“TACP”) and Toshiba Hawaii Inc. (“THI”) make the following limited warranties. These limited warranties extend to the original consumer purchaser or any person receiving this set as a gift from the original consumer purchaser and to no other purchaser or transferee .
How to Obtain Warranty Service If after following all of the operating instructions in this manual and checking the section “Before calling service personnel” and you still find that service is needed; ( 1 ) Call the TACP toll free number 1-800-631-3811 after you find a defective product or part to find the nearest Toshiba Authorized Service Station. ( 2 ) Please present your bill of sale or other proof to the Authorized Service Station.
