CMOS COLOR CAMERA INSTRUCTION MANUAL IK-HR2D For Customer Use Enter the Serial # (which is located on the bottom of the cabinet) below. Retain this information for future reference. Model # Serial # IK-HR2D FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
SAFETY PRECAUTIONS Safety icons This manual contains safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and the icons highlight these instructions as follows: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Note the following instructions when installing. • Do not cover the product with any material. • Do not place the product on any inflammable material such as a carpet or blanket. • Do not place the product in a confined space, as this may cause heat to build up inside the product. Failure to follow the above cautions may result in fire. Do not place the product in direct sunshine and/or high temperature. Temperature build up inside the product may result in fire.
Limitation of Usage The product is not designed for any “critical applications.” “Critical applications” means life support systems, exhaust or smoke extraction applications, medical applications, commercial aviation, mass transit applications, military applications, homeland security applications, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage.
(3) WHT BAL (White Balance) .......................................................................................... (3.1) Changing the setting in AWB (Automatic White Balance) mode ........................ (3.2) Changing the setting in ATW (Automatic Tracking White balance) mode ......... (3.3) Changing gain in MANUAL mode ....................................................................... (4) PROCESS ....................................................................................................
1. CAUTIONS ON USE AND INSTALLATION • • Handling the unit. • • Install the camera in a location free from noise. If the camera or the cables are located near power utility lines or a TV, etc. undesirable noise may appear on the screen. In such a case, try to change the location of the camera or the cable wiring. • Operating ambient temperature and humidity. • Do not use the camera in places where temperature and humidity exceed the specifications.
3. NAMES AND FUNCTIONS 2 DC IN 12V terminal 1 Prism faceplate 5 DISP button 7 MENU UP button 9 DATA UP (AWB) button 10 DATA DOWN button 8 MENU DOWN button 6 PAGE button 4 DVI-D terminal 3 USB terminal [ Front ] 11 [ Rear ] 12 Rear [ Bottom ] 䐖 Prism faceplate The protection cap is attached on the lens mount portion. After removing the cap, mount the lens. Be careful not to scratch or touch the optical area. 䐗 DC IN 12V terminal Accepts a DC power input (12V). 䐘 USB Terminal USB terminal.
4 CONNECTION 4 1 Standard Connection Lens (option) DVI terminal IK-HR2D Less than 11 mm [0.433”] DVI cable (not supplied) DVI monitor (not supplied) USB terminal DC IN 12V DC power supply Tri-pod adapter (option) (option) USB cable (not supplied) PC (not supplied) 4 2 Cautions on Connection ࣭When connecting the camera cables, be sure to turn off the CMOS color camera and any other equipment connected to it.
* Recommended PC: O S : Windows® XP SP2 - SP3 Windows Vista® Windows® 7 C P U : Intel® Pentium® compatible (x86 or x64) CPU 1 GHz or more. Memory : 512 MB or more * Please be aware that this camera will depend on the computer, environment, or cables and unless these are compatible, the camera may not operate correctly. * Please be aware that the PC will be required to run DirectX® as the API (Application Program Interface) to interface with the video from the camera.
5 OPERATION 䐖 Refer to the item "4. CONNECTION", and connect the equipment correctly. 䐗 Turn on the connected equipment and the camera. 䐘 Aim the lens at the object, adjust the lens iris adjustment, focus adjustment, etc. 䐙 Refer to the item “5.1 White Balance”, make the adjustment. 䐚 Please see “5.2 Gain”, “5.3 Switching video signal output” and “7. MODE SETTING BY THE ON SCREEN DISPLAY” to carry out necessary operations. 䐛 Please see “5.
Display Meaning AWB OK Automatic white balance adjustment finished correctly. AWB NG Automatic white balance adjustment cannot be performed because the video level is too low. Adjust the video level by increasing the illumination or opening the lens iris. LEVEL LOW AWB NG LEVEL HIGH AWB NG C. TEMP LOW Automatic white balance adjustment cannot be performed because the video level is too high. Adjust the video level by decreasing the illumination or closing the lens iris.
5 2 Gain When the image is dark even if the lens iris is open, change the gain (video gain) to get the desired video level. For gain adjustment of the unit, MANUAL (Manual), OFF (0 dB) modes are provided. Select the mode on the GAIN menu. (Refer to the item “7.3 (2) GAIN (Video gain)”.) (1) MANUAL(Manual gain) Gain adjustment is performed on the GAIN menu. The adjustment range is from 0 to 18dB in 1dB steps. (Refer to the item “7.3 (2) (2.1) Changing gain in MANUAL mode”.) (2) OFF Gain is fixed at 0 dB.
5 4 Display video with USB 䞉㻌 Connect a USB terminal of the camera and a USB terminal of the computer with a USB cable. 䞉㻌 Turn on the power of both the camera and the computer. 䞉㻌 Run the viewer software. * Please use a cable supporting mini-USB (B type) for the USB terminal of the camera. * To display video captured by the camera, viewer software supporting USB Video Class is required separately. 䚷 * In case of Windows® XP SP2 or SP3, the built-in viewer software can be used.
6 ITEMS CONTROLLED BY THE ON SCREEN DISPLAY Item Available selections Electronic shutter MODE AUTO level AUTO peak : average AUTO response speed AUTO area Gain White balance Process Matrix color correction AUTO, MANUAL, SS -100 0 100 00 10 05 05 10 00 1 10 20 PRESET A, PRESET B, PRESET C, PRESET D, PRESET E MANUAL speed OFF, 1/100s, 1/125s, 1/250s, 1/500s, 1/1000s, 1/2000s, 1/4000s Syncro.
7 MODE SETTING BY THE ON SCREEN DISPLAY Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The contents once set are memorized in the scene files (A, B, C, D, E) selected, so if the power turns off, it is unnecessary to set the values again when using the unit next time. When the setting is performed, select the menu of the item to be set.
7 2 Scene File Five scene files (A, B, C, D, E) are available as user memories for this unit. These are chosen depending on shooting conditions. By pressing [DATA UP], [DATA DOWN] buttons while [DISP] button is pressed and the index menu is displayed, the camera operation is changed immediately from the currently selected scene file to the next.
䟺1䠀 䠀1䟻 䟻 Changing the setting in AUTO mode Move up and down by pressing MENU UP,DOWN Select the desired value by pressing DATA UP,DOWN Shutter mode -- 1 SHUTTER -- MODE LEVEL PEAK AVE SPEED AREA AUTO, MANUAL, SS Video level adjustment -100 to 100 Peak and average ratio adjustment AUTO 0 05 05 10 PRESET A 00 10 to 10 Automatic shutter response speed adjustment 1 to 20 Automatic shutter area selection PRESET A, PRESET B, PRESET C, PRESET D, PRESET E < MODE = AUTO> (a) Changing the vi
(d) Changing the automatic shutter zone area 䐖 Move the “䊲” to AREA by pressing [MENU UP], [MENU DOWN] buttons. 䐗 Select the measurement light area by pressing [DATA UP], [DATA DOWN] buttons. 䠭DATA UP䠯 PRESET A PRESET B PRESET C PRESET D 䠭DATA DOWN䠯 PRESET E The available picture area is divided into 64 rectangles. The user can choose one of 5 presets. The shaded rectangles represents the area/pattern where the sampling is taken from.
(a) Changing the shutter speed 䐖 Move the “䊲” to MANU by pressing [MENU UP], [MENU DOWN] buttons. 䐗 Select the shutter speed by pressing [DATA UP], [DATA DOWN] buttons. 䠭DATA UP䠯 OFF 1/100s 1/125s 1/250s 1/500s 1/1000s 䠭DATA DOWN䠯 1/2000s 1/4000s Note: The shutter speed can be set in every effective scanning line (1080/720). The figures of shutter speed in the menu screen are approximate. The accurate shutter speed is calculated using the following mathematical formula.
2 GAIN (Video gain) GAIN has two modes; MANUAL, OFF. Move the “䊲 ” to MODE, press the [DATA UP], [DATA DOWN], and select one of the two modes : MANUAL, OFF. In the OFF mode, gain is fixed to 0dB.
(a) Changing R PAINT 䐖 Move the “䊲” to R PAINT by pressing [MENU UP], [MENU DOWN] buttons. 䐗 Select the desired value of red paint by pressing [DATA UP], [DATA DOWN] buttons. [DATA UP] - 10 Red is decreased. ࠉRed is increased. 0 10 ࠉ [DATA DOWN] (b) Changing B PAINT 䐖 Move the “䊲” to B PAINT by pressing [MENU UP], [MENU DOWN] buttons. 䐗 Select the desired value of blue paint by pressing [DATA UP], [DATA DOWN] buttons. [DATA UP] - 10 Blue is decreased. ࠉBlue is increased.
䟺3䠀 䠀2䟻 䟻 Changing the setting in ATW(Automatic Tracking White balance) mode Move up and down by pressing MENU UP,DOWN -- 3 Select the desired value by pressing DATA UP,DOWN WHT BAL -- MODE R PAINT B PAINT ATW 0 0 White balance mode AWB, ATW, MANUAL R PAINT adjustment -10 to 10 B PAINT adjustment -10 to 10 (a) Changing R PAINT 䐖 Move the “䊲” to R PAINT by pressing [MENU UP], [MENU DOWN] buttons. 䐗 Select the desired value of red paint by pressing [DATA UP], [DATA DOWN] buttons.
䟺3䠀 䠀3䟻 䟻 Changing gain in MANUAL mode Move up and down by pressing MENU UP,DOWN -- 3 Select the desired value by pressing DATA UP,DOWN WHT BAL -- MODE R GAIN B GAIN C TEMP MANUAL 0 0 3200K White balance mode AWB, ATW, MANUAL Red gain adjustment -100 to 100 Blue gain adjustment -100 to 100 Color temperature setting 3200K, 5600K (a) Changing the red gain 䐖 Move the “䊲” to R GAIN by pressing [MENU UP], [MENU DOWN] buttons.
䟺4䟻 䟻 PROCESS Move up and down by pressing MENU UP,DOWN Select the desired value by pressing DATA UP,DOWN Gamma correction -- 4 PROCESS -- GAMMA ON/OFF GAMMA DTL GAIN DTL B.FREQ M PED ON, OFF Gamma correction level setting Detail gain setting ON 0 0 HIGH 0 -10 to 10 -7 to 7 Detail boost frequency Master pedestal setting HIGH, NORMAL, LOW -128 to 127 䟺4䠀 䠀1䟻 䟻 Changing gamma correction ON/OFF 䐖 Move the “䊲” to GAMMA ON/OFF by pressing [MENU UP], [MENU DOWN] buttons.
䟺 4䠀 䠀3䟻 䟻 Changing detail (outline) gain 䐖 Move the “䊲” to DTL GAIN by pressing [MENU UP], [MENU DOWN] buttons. 䐗 Select the desired value of the detail gain by pressing [DATA UP], [DATA DOWN] buttons. [DATA UP] -7 The detail decreases. ࠉThe detail increases. 0 7 ࠉ [DATA DOWN] 䟺 4䠀 䠀4䟻 䟻 Changing DTL B.FREQ (detail boost frequency) This setting adjusts the thickness of the image outline. 䐖 Move the “䊲” to DTL B.FREQ by pressing [MENU UP], [MENU DOWN] buttons.
䟺5䟻 䟻 MATRIX(Matrix color correction) Move up and down by pressing MENU UP,DOWN Red hue setting -- 5 MATRIX -- Red gain setting MATRIX ON Green hue setting R R G G B B 0 0 0 0 0 0 Green gain setting Blue hue setting Blue gain setting Select the desired value by pressing DATA UP,DOWN HUE GAIN HUE GAIN HUE GAIN Matrix color correction ON, OFF Yellow hue setting Yellow gain setting Ye Ye Cy Cy Mg Mg HUE GAIN HUE GAIN HUE GAIN 0 0 0 0 0 0 Cyan hue setting Cyan gain setting Magenta hu
䟺6䟻 䟻 OPTION Select the desired value by pressing DATA UP,DOWN -- 6 OPTION MONITOR -- MONITOR PC PC, TV 䟺 6䠀 䠀1䟻 䟻 Changing a type of output monitors Select either PC or TV by pressing [DATA UP], [DATA DOWN] buttons. 䝿 PC: When using PC as an output monitor. 䝿 TV: When using TV as an output monitor. Note: Select PC or TV depending on the DVI monitor you use. If TV is selected, the brightness on the monitor will be increased. This setting has nothing to do with the USB video output.
8.
10. EXTERNAL APPEARANCE DIAGRAM Unit : mm [inch] 26 [1.02] 2-M3 Depth 3 [0.118] 5 [0.2] 78 [3.07] 10.65 [0.42] 6.3 [0.25] 44 [1.73] 22 [0.87] 44 [1.73] 32.51[1.28] [Front] [Rear] 56 [2.2] 4-M2 Depth 3 [0.118] 4-M3 Depth 3 [0.118] 26 [1.02] 25 [0.98] 26 [1.02] 5 [0.2] 25 [0.98] 25 [0.
Limited Warranty –TOSHIBA CMOS Color Camera The Imaging Systems Division of Toshiba America Information Systems, Inc. ("ISD") makes the following limited warranties with regard to this CMOS Color Camera ("Product"). These limited warranties extend to the Original End-User ("You[r]"). One (1) Year Limited Warranty of Labor and Parts ISD warrants that this Product will perform in accordance with specifications for a period of one (1) year from the date of purchase by the Original End-User.
