Blu-ray Disc™ Player BDX2300KE Owner’s Manual BDX2300KE full manual_3-6.
Contents English 1 Important.................................................................................................................... 3-4 Safety and important notice...............................................................................................3 Disposal of your old product and batteries....................................................................... ...3 Notice for Trademark...................................................................................................
Safety and important notice • • • • • • Disposal of your old product and batteries Warning: Risk of overheating! Never install the product in a confined space. Always leave a space of at least 10cm around the product for ventilation. Ensure curtains or other objects never cover the ventilation slots on the product. Never place the product, remote control or batteries near naked flames or other heat sources, including direct sunlight. Only use this product indoors.
Notice for Trademark English HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. BONUSVIEW ™ Blu-ray DiscTM, Blu-rayTM, BD-LiveTM, BONUSVIEWTM, and the logos are trademarks of the Blu-ray Disc Association. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Manufactured under license under U.S.
Region Regions Codes Both the Blu-ray DiscTM Player and the discs are coded by region. These regional codes must match in order to play the disc. If the codes do not match, the disc will not play. The Region Number for this Blu-ray DiscTM Player is described on the rear panel of the Blu-ray DiscTM player. Region DVD discs that can be played U.S.A.
Product overview English Main Unit 8 7 6 5 4 3 NO Control Function a USB jack Connect a USB flash drive. b 1 Turn the power on or restores the unit to the standby mode. c B/X Playback/Pause. d x Stop play. e Z Open or close the disc compartment. f IR Sensor Point the remote control at the IR sensor. g Display panel Show information about the current status of this unit. h Disc compartment Load a disc into the disc drive.
English Remote Control OPEN/CLOSE • Open/ Close the disc tray Number Buttons Select numbered items in a menu Press to enter track/ chapter/ title numbers/password directly CLEAR • To clear an entry or the bookmark and program you set MC(Media Center) • To open/close Media Center POP UP/MENU • To display a menu included on many Blu-ray Disc™/DVD video discs OK • Acknowledge/ Confirm menu selection • Navigation/ Cursor buttons for moving to the left / right / up / down • Press during JPEG playback to ro
3 Connections English Make the following connection to use this product. Connecting to a TV Option 2: Connect to network Connect this product to the network to enjoy BD-LiveTM bonus content and software upgrade by network. Connect the product to TV via HDMI jack to view the playback from the disc. Connect to the HDMI Jack HDMI IN 1. Connect the network cable from the LAN jack on the product to the LAN jack on the network system.
Connect USB device English The USB jack supports USB flash drive, TOSHIBA's USB Wi-Fi® adapter (Model name: WLM-12EB1) and 4 ports USB HUB. A USB flash drive provides an additional memory to software upgrade and enjoy BD-LiveTM bonus content. You can also enjoy playing back MP3/ JPEG/MPEG4/DivX® files stored in the USB flash drive. 1. Connect the USB flash drive or TOSHIBA's USB Wi-Fi® adapter to the USB jack on this product.
4 Preparation English Always follow the instructions in this chapter in sequence. Note: - Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. Setting up the player Find the correct viewing input 1. Press 1 to turn on this product. 2. Turn on the TV and switch to the correct video-in input (refer to the TV user manual on how to select the correct input).
Playback Functions Basic Playback 1. Press button on the front panel or the remote control, your Blu-ray Disc™ player will turn on. The unit will take around 20 seconds to warm up. When the power supply is first switched on, the setup of the Power Down Mode is in Normal mode. 2. Turn on the TV, and then select the input setting on the TV that matches the connection method you used to connect your player. 3. Press OPEN/CLOSE Z to slide out the disc tray. 4.
Advanced Playback English DISPLAY Press this button and the screen will display some information about disc, such as: Title number, Chapter number, Track number, Elapsed Time, Mode, Audio, Angle, and Subtitle languages. Press this button again to turn off the information display. During DVD/CD playback, you may edit the chapter and track REPEAT Press REPEAT repeatedly to select different repeat modes. Blu-ray DiscTM: Repeat Chapter and Title. DVD: Repeat Chapter, Title and All.
[Time]: View the elapsed/remaining playback time of title/chapter. Use / to view: the elapsed playback time of title, the remaining playback time of title, the elapsed playback time of chapter, and the remaining playback time of chapter. [Mode]: Select playback mode among shuffle, random, and normal. [Audio]: The Blu-ray DiscTM/DVD disc’s soundtrack language. Use / to view the audio available in the disc and select your desired Audio type.
Blu-ray DiscTM BONUSVIEWTM English Playing Secondary Video (Picture-in-Picture) and Secondary Audio is for Blu-ray DiscTM only. Secondary video can be played from a disc compatible with the Picture-in-Picture (PIP) function. For the playback method, refer to the instructions for the disc. 1. Turn on secondary video by pressing the PIP button. 2. Press the PIP AUDIO button to select the secondary audio, and select an option except Off.
Load Default Select "Yes" or "No" using /. Resolution has been changed! 14s Yes Does everything looks all right with this resolution? Press Yes if you want to apply it. Press No to rollback to previous one. Previous English all REGZA-LINK-compliant devices that are connected through HDMI connectors. {On} - Turns on REGZA-LINK features. -With CEC on, during TV standby with the Blu-ray DiscTM player on, pressing SETUP, PLAY/PAUSE will power on the TV.
English UPG_ALL, and copy the upgrade file into this folder. SW upgrade by Internet introduction There are two modes to upgrade via internet: Automatic Mode and Interactive Mode. Automatic Mode: The player will check the internet whether it is connected automatically when powered on. If connected, player will try to connect the Toshiba server to check if there is new firmware for the player.
General Setting System OSD English Language Menu English Playback Audio English Security Subtitle English Network Move cursor key to select menu option then use “OK ” key to select SETUP Exit • [OSD] Select the default on-screen display language. • [Menu] Select the default menu language. • [Audio] Select the default audio language. • [Subtitle] Select the default subtitle language. [Playback] General Setting System Angle Mark On Language PIP Mark On Playback Secondary Audio...
[Security] 3. Select a rating level, then press OK. General Setting General Setting Change Password More... System Language Country Code More... Language Playback Parental Control More... Playback English System Screen Save Off Parental Control Disc Auto Playback On Select level: Off CEC On [1] KID SAFE Security Security [2] G Disc Auto Upgrade On Network Network Load Default More...
3. Then open web browser to go to the router setting page to input the PIN code. 4. Select "Next" on the Blu-ray DiscTM player. 5. Press SETUP to exit. Notes: - USB Wi-Fi® adapter is required for a wireless connection (not supplied). - This unit is compatible with TOSHIBA's USB Wi-Fi® adapter only (Model name: WLM-12EB1). - Connect the TOSHIBA's USB Wi-Fi® adapter to the USB jack on this product. - Ensure that the Wifi router is switched on.
English by using the on-screen software keyboard. Strings(1-15 characters), [A-Z][A-Z0-9]* {User Name} Input the User Name (to control the Blu-ray DiscTM player from the iPhone etc.) by using the on-screen software keyboard. Strings(Max. 16 characters), [a-zA-Z0-9] [a-zA-Z0-9_-¥.]* {Password} Input the Password (to control the Blu-ray DiscTM player from the iPhone etc.) by using the on-screen software keyboard. Strings(Max. 16 characters), [a-zA-Z0-9] [a-zA-Z0-9_-¥.
Notes about HDMI 1080/24p: If you want the 1080/24p output, it should fulfill below 3 conditions: 1.TV supports the 1080/24p display; 2.Player choose the 1080/24p option in the setup menu; 3.Media must be the 1080/24p video. Notes: - This resolution becomes effective only when the playing Blu-ray Disc™ contents are Film source. - During HDMI 1080/24p playback, there will be no composite output. [Video Process] Display Setting TV Video Adjust More...
English • [Down_samp] Select the digital audio signal sampling frequency. (Only Coaxial) {48K} – For discs recorded at sampling rate of 48 kHz. {96K} – For discs recorded at sampling rate of 96 kHz. {192K} – For discs recorded at sampling rate of 192 kHz. • [Dolby DRC] Select the Dynamic Range Control mode which makes it available to listen to a movie at a low volume without losing sound clarity. {Off} – Non-dynamic range compress. {On} – Dynamic range compress.
English • Featured: Display the featured photos from Picasa website. • Friends: Display the list of friends. • Search: Search photos based on keywords. • Favorites: Display the favourite photos from your Picasa Web Albums. • Tag: Display the photos that have been tagged in your Picasa Web Albums. 6. To exit the Picasa page, press RETURN. Play a slideshow 1. Use the remote control to select “My Photos” from the Picasa page, and press OK. »» The photos in your Picasa Web Albums are displayed in thumbnails.
7 Specification English Playable media This product can play: • Blu-ray Disc™-Video, BD-R/RE2.0, BDAV • DVD, DVD-Video, DVD+R/+RW, DVD-R/-RW, DVD+R/-R DL (Dual Layer) • Video CD/SVCD • Audio CD, CD-R/CD-RW • AVCHD • USB flash drive Video Signal system: PAL/NTSC HDMI Output: 480i/576i, 480p/576p, 720p, 1080i, 1080p, 1080/24p. Audio • Digital output (Coaxial): 0.5 Vp-p (75 ohm) • HDMI output LAN • LAN terminal 10BASE-T/100BASE-TX USB • USB 1.1 / USB 2.0 Full-speed / USB 2.
8 Troubleshooting Problem Tip No reaction to the remote control. Connect the product to the power outlet. English If you experience any of the following difficulties while using this unit, check the list below before consulting your nearest TOSHIBA dealer. Point the remote control at the product. Insert the battery correctly. Insert new battery in the remote control. No video signal on the display device. Turn on the TV. Set the TV to the correct external input. Select the correct video resolution.
Cannot find a JPEG file. Make sure that the selected group (folder) does not contain more than 9,999 files for DVD and 999 files for CD. English Make sure that the file extension is .jpg, .JPG, .jpeg or .JPEG. Cannot find a MP3 file. Make sure that the selected folder does not contain more than 9,999 files for DVD and 999 files for CD. Make sure that the file extension is .mp3 or .MP3. Cannot upgrade SW.
Aspect ratio Aspect ratio refers to the length to height ratio of TV screens. The ratio of a standard TV is 4:3, while the ratio of a high definition or wide TV is 16:9. The letterbox allows you to enjoy a picture with a wider perspective on a standard 4:3 screen. AVCHD™ AVCHD™ is a new format for high definition video camcorders which can record and play high-resolution HD images. AVI Audio Video Interleave, known by its acronym AVI, is a multimedia container ormat.
English DTS-HD Master AudioTM A disc encoded with DTS-HD Master Audio delivers ALL of the information from the original master recording — bit-for-bit, it's identical to what the sound engineers laid down. Audio doesn't get any better than this. HDCP High-bandwidth Digital Content Protection. This is a specification that provides a secure transmission of digital contents between different devices (to prevent unauthorized copyright.
The software pre-installed in this product consists of multiple, independent software components. Each software component is copyrighted by a third party. This product uses software components that are distributed as freeware under a third-party end-user license agreement or copyright notice (hereinafter referred to as a “EULA”). Some EULAs require that the source code of the applicable component be disclosed as the condition for distributing the software component in executable format.
English gzip GPLv2 inetutils GPLv2 ncurses ncurses.txt gdb (gdbserver) GPLv2 Das U-Boot GPLv2 International Components for Unicode ICULicense.txt OpenSSL openssl.txt zlib zlib.txt FreeType FreeType.txt Expat expat.txt libcurl libcurl.txt libjpeg libjpeg-7.txt c-ares c-arse.txt mtd-utils GPLv2 libmtp LGPLv2.1 libusb LGPLv2.1 libusb-compat LGPLv2.1 WPA Supplicant WPASupplicant.txt WPA Supplicant (WPS) WPASupplicant.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software.
English 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. the library.
English any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute. 7.
PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. English 16.
The FreeType Project is distributed in several archive packages; some of them may contain, in addition to the FreeType font engine,various tools and contributions which rely on, or relate to, the FreeType Project. 3. All advertising materials mentioning features or use of this software must display the following acknowledgement: "This product includes cryptographic software written by Eric Young (eay@cryptsoft.
English 1. No Warranty http://www.freetype.org THE FREETYPE PROJECT IS PROVIDED `AS IS' WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL ANY OF THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED BY THE USE OR THE INABILITY TO USE, OF THE FREETYPE PROJECT. Expat 2.
This software is copyright (C) 1991-1998, Thomas G. Lane. All Rights Reserved except as specified below.
THIS SOFTWARE AND ITS DOCUMENTATION, EVEN IF THE COPYRIGHT HOLDER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. English THE COPYRIGHT HOLDER SPECIFICALLY DISCLAIMS ANY WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE SOFTWARE PROVIDED HEREUNDER IS ON AN "AS IS" BASIS, AND THE COPYRIGHT HOLDER HAS NO OBLIGATION TO PROVIDE MAINTENANCE,SUPPORT, UPDATES, ENHANCEMENTS, OR MODIFICATIONS.
THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED WARRANTY. IN PARTICULAR, NEITHER THE AUTHOR NOR LUCENT MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE. bison_parser The distribution terms for Bison-generated parsers permit using the parsers in nonfree programs. Before Bison version 2.2, these extra permissions applied only when Bison was generating LALR(1) parsers in C.
