Manual

Beforecallinga seMce technician please
Probmem
TVwill not turn on
Picture )roblems
checktile fellowingtablefor a possiblecauseof tile problemand somesolutions.
Solution
o Make sure the power cord is plugged h/and then press POWER.
o Theremote control batteries maybe dead. Replacethe batteries or try the front par]elbuttons
o Pressthe RESETbutton on the TV front pane] (page 9)
o Ifyou have recently replaced the lamp unit, make sure the lamp Llnitand lampunit door are installed
properly (pages 98-100)
o The]ampunit may needto be replaced (pages 98-100)Also see "LED indications" on page 94.
o Checkthe anterlna/cable connections (Chapter 2}.
o PressINPUT on the remote control or TV/VIDEO or/the TVfront panel arid select a valid video ir/put
source (page 67), If no device is connected to any ofthe inputs on the 'FV,no picture will displaywhen
you selectthat palsicularinput source. Fordevice connection details, seeChapter 2.
o Anter/na reception may be pool- Use a highlydirectional outdoor antenr/a (if applicable}.
° The station mayhave broadcast difficulties. Tryanother channel
o Adjust the picture qualities (page 7(_).
o [fyou are using a VCR, make,_urethe TV/VCRbutton on the remotecontrol is set correctly (page 27)
o [fyou have two VCRs connected to your TV,do not connect the same VCR to the TV's output and input
connections at the ,_arnetime (page 18).
o Do not connect a standard video cable and an S-video cableto VIDEO-1 or VIDEO-2 on the W back (or
VIDEO-3 on the ]_/front) at the same time (Chapter 2).
Noisypk:'turs o [fyou are watching a tuned analog char/nel (off-air broadcast or Cable TV),set the CableClearDNR
featureto AUTOto reduce visible interference in the P,! picture (page 77)
Video/nput Selection
pr_:,b/ems
o [fthe hlput Selectionwir/dow does not appear wher/you press INPUTon the remote control or
TV/VIDEO on the TVfront panel, press INPUTor TV/V[DEO a second time, which will change to the next
video input source and display the InpLJtSelection window
(,_nnot view external signa/s
or channe/ 3 or 4
o Ifyou cannot view signalsfrom external devices connected to VIDE() 1,VIDEO 2
VIDEO 3 or ColorStream; or from channels 3 or 4, make sure the INPUT LOCKis set to OFF(page 90)
Black bo'<on screen
o Setthe CLOSEDCAPTION feature to OFF(page 78}
POOr CO/OF Of 120 CO/OF
° The station may have broadcast difficulties. Try another channel
o Adjust the TINT and/or COLOR (page 76}.
o When the ColorStream sigr/al source is active, the VIDEO OUT terminal outputs blank video. To receive
video frorn the VIDEO OUT signal, a starldard video or S-video [N jack must be used instead of the
ColorStream connections.
POPprob/ems
Memory card
problems
TheVIDEO OUTjack will not output the POPpicture (pages 18and 74)
Make sure you areusing a supported or walidmemory card format (page 82}
Make sure you havesaved the picture files in the correct file format (page 82}.
Thecard may be inserted improperly. Ren/ovethe card and reinsert it (page 82)
Thememory card may beempty.
Thememory card may bedamaged.
÷
HM94(E)09_
92
-97(10-Trbl)
92
Copyright #) 2004 TOSHIBA CORPORA]ION. All rights reserved.
÷
8/31/04,11:43 AM
F