Manual

A ÷ L
The TheaterNet fbature allows you to control many brands of"
IEEE-1394 and/or infrared rernote<ontrolDd A/V devices
through your TV using on-screen control icons and the TV's
remote control
Note:
• Ah'hol_qh the777eaterNetonscreendevke c:ontmlfem'uzeincludes
codesformanycleviees,it maynotincludecodesforsomeoraNof
therestartsonoert;dndeviees you wishtoCOfTtfeLff J/OU am unable
toprogramrite Theate/Netteature17>operate yourdeviceofso177eof
thefeatul>sonthatdevice, use thedevice_remotecontlo/of the
COfTtfel!_ Of 7 the device
• For IR pass thmt\qh device control bfo/mation, see "('onnecting
kFmmd remote cof?tlo//ed (Jel/ioes to the/R OUT[/Jol<" Oll page 2 7
Setting up TheaterNet
AII de, ice types except IEEE-1394 require the fblh)wing seRtp
process befbre you can contro_ them using the TheaterNet
on-screen icons.
AH CompatibD IEEE-1394 devices are atnomaticaIIy recognized
by the TheaterNeE fbature and do not require setup.
Note: .Seepnge 22 for det_dsaboutthe IEEE 1394per> IfyoL/_
/EEE 1394deviceisf}ot recognizedthrotJgh theIEEE 1384po£ or
ffTletJ_h {lie 7heaterNetfentu/_,it maybe possibleto set ituptot IR
passt/IrotLq/Ioontro/ as atlhTf/_lreddevice(seepage 20
To set up TheaterNet device control:
1. Make sure you have properly connected your infrared
remote-controlled device(s). See page 21 for details.
2. Press MENU and open the SETUP menm
3. HigNight INSTALLATION and press ENTER. (A new set
of'INSTALLATION menu icons will appear on-screen, as
shown in step 4).
Open the DEVICES menu, highlight THEATER NET
DEVICES, and then press ENTER.
Navigate _Se]ect _t3.ck _,_E×Jt
The TheaterNeE Setup menu opens.
5. Using the _t _ buttons, sdect the INPUT the device is
connected to.
Note: Ygher7the input/s change< all unsaved settings
Jvi/Ibe lost
6. Press V and then *__ to sdect the device TYPE.
7. Press _' and then @_ to sdecr the device BRAND
Note: Whorl selecting a tlew brand, the IR oode will/)e set
I_) 7ere
8. Press _' and then *__ to sdect the device's IR code.
9. If the desired IR code is found, skip to step 10.
If the desired IR code is not in the list, press V and use the
ChamM Number buttons to enter the device IR code.
Note: _)u can find tile IR code _)r you/ device in the
oil sc/_en list or k7the 2?eaten\let device ooo'e t_bb of 7
pages 4U 48
10, Highlight TEST and press ENTER to test whether the
device responds to the code.
If"the device does not respond to the code, repeat steps
8 and 9 using another code for the same device.
11. When done, highlight SAVE and press ENTER.
To remove a device from TheaerNet:
1, Follow steps 1-5 above.
2. Highlight RESET and press ENTER.
3. Highlight SAVE and press ENTER.
÷
HM94(E}O4Z
44
-51(6b-Setup} 44
Copyright @)2904 TOSHIBA CORPORATION. A[] rights reserved.
÷
8/31/04, 2:09 PM
[