Manual

ManualsBrandsToshiba ManualstelevisionOfficial Toshiba dlp television

A ÷ [

Programmingthe remote control to operate yourother devices

Device code setup

1_ Refer to the muIti-brand remote contro_ device code table

on pages 32-33 to find the code for the brand of'yottr

device.

If'more than one code is listed, try each one separatdy until

3xmfind the one that works.

2. Press MODE mlfiI the Mode indicator fbr the device

(CBL/SAT, VCR/PVR, DVD, AUDIO 1, AUDIO 2)

lights up.

3. While holding down the RECALL bumm, press the

Channel Number buttons to enter d_efbur-digit code fbr

your brand of'device. If'a valid code is entered, the mode

indicator will blink twice. If'an invalid code is entered, she

mode indicator will blink one long blink.

4. Point the remote control at the device and press POWER to

test the code.

ff'&edevice l*'sf,ovds> &e l_','_ow_,wol:

You have entered the correct code.

ff'&e devicedoeyJ_otre_j.,ovdh &e re,,_olecomrol:

You may have entered the wrong code. Repeat steps 3

and 4 using another code.

Note: ir_addition to POVdER,coslfhz71that aNnecessa/y keys

of 7the TV f_fTsotecrJp_/olopel_ffe you[ cievice ff some keys

are not opei_@)na/, repeat the device code setup LisiiW

8fsothe/ code (if otlse/ codes 8re//{_ted for you/ devicej

St,afte/ tfyieg all i/sted codes, the necessa/y keys rio slot

oper_m your dev/ce, use rise device_ of_4ii?aitemote cont/o/

5. Press MODE to select the TV mode to control the TV.

Note:

• /although the TV_emote c'of7tlol inciudes codes for masly device& it may

not/rsclude codes for some or all of the features on certain ciev/cesyou

wish to controL ifyou are unable to progr_sm the TV femote cofstf_)/to

operate you/cievice o_ some of the features on that o'ev/ce, use the

device's fwnote control or the cosltmh oslthe device

• _)schtimeyoudsailgetheba_eriesyouw///needtoreprog/_mthe

remote cosfffoZ

• Some fsewe/VORs [espof)ci to e/the/of two codes These VCR_ have a

sw/lch bbe/ed "VCRWVCR2" /@our VCR has this kind of switch and

does not _espond to tile codes for VotJ/VCP,brand, set the switch to _?se

other posiUon ("I/'CR 7"or "VC?R2') and teptogm£rl tile tWTsoteco/st[oL

Searching and sampling the code

of a device (8500)

If'you do riot know the device code f'ora particular device, you

can cycIe the remote controI through the avaiIabIe codes for that

device mode and sample the f'mlctions to find the code that

operates the target device. The keys avaihbIe to be sampled,

provided they are applicable to that mode, are POWER, 1,

VOL &, CH &, and PLAY.Invalid keys will be ignored while in

program mode.

To cycle through each available device code and sample its

_nctions:

Press MODE to select the mode you want to set up.

WhiIe biding down RECALL, press 8 - 5 - 0 - 0.

The remote control will enter program mode.

Point the remote control at the target device and press

POWER (or other f'ttnction buttons that are available to be

sampled).

/TiDe device respowts> &e re,,_otec0mr0L'

Press RECALL to store the device code. The mode

indicator will blink twice and the remote control will exit

the program mode.

ff'&edevicedoess_otres?ond > &e rev_olecovtrol:

Press A, arid then press POWER.

Repeat this step until the device responds co the remote

control, and then press RECALL.

Note: When a seamh cycle h comp/eter/, the mode

indioalor vdii b/ink throe times. The remote oontto/ wi//

begin Io r:yc/e Usmugh the avai/ab/e codes again, if no key

is pressed wilhir? 10 seconr/s whi/e programming, lfse

remote cotstsT/ win exit he program mode and return to file

pmvsbus corse.

-- POWER

-- Numbers

MODE

--VOL A/_

i RECALL

HM94(E)026 33(3-RC)

30 . 8/31/04, 1:08 PM [