9EL833G 22EL833G DIGITAL Series OWNER’S MANUAL
Contents A01_MB60_[GB]_(IB_INTERNET)_DVB-TC_(CT90326)_1007xxxx_5018xxxx_v4.indd 1 English Viewing Info Banner.......................................... 19 Electronic Programme Guide............................ 19 Language Selection .............................................. 20 Language Settings ............................................ 20 Preferred ........................................................... 20 Current ..............................................................
English Using a Conditional Access Module ................. 27 Setting Timers, Setting Date/Time ........................ 28 Timers ............................................................... 28 Setting Sleep Timer .......................................... 28 Setting Programme Timers ............................... 28 Configuring Date/Time Settings ........................ 28 Source Settings, Other Controls ........................... 29 Configuring Source Settings .............................
Safety Precautions Air Circulation Do not Leave more than 10cm clearance around the television to allow adequate ventilation. This will prevent overheating and possible damage to the television. Dusty places should also be avoided. DON’T remove any fixed cover as this may expose dangerous voltages. Heat Damage Damage may occur if the television is left in direct sunlight or near a heater.
Installation and Important Information Where to install English Sturdy tie (as short as possible) P Clip * Button and stand style is dependent on model. P Clip “P” Clip position on TV is dependent on model. Locate the television away from direct sunlight and strong lights. Soft, indirect lighting is recommended for comfortable viewing. Use curtains or blinds to prevent direct sunlight falling on the screen. Place the TV on a stable, level surface that can support the weight of the TV.
Important safety information USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL. English WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT. Headphone Warning Loud music can damage your hearing irreversibly.
Important safety information (continued) English • Ensure that the unit is sufficiently ventilated! Never place it next to or underneath curtains! • This set should only be connected to an 220-240V AC 50Hz mains power supply. Do not attempt to connect it to any other type of supply. • The unit becomes warm when in operation. Do not place any covers or blankets on the unit in order to prevent overheating. The ventilation holes should not be blocked. Do not set up near radiators.
To display your LCD TV using a wall bracket (1) Caution: Two people are required for installation. (2) Unplug and remove any cables and/or other component connectors from the rear of the TV. (3) Follow the instructions provided with your wall bracket. Before proceeding, make sure the appropriate bracket(s) are attached to the wall and the back of the TV as described in the instructions provided with the wall bracket.
The Remote Control English Simple at-a-glance reference of your remote control. Standby / On mode AV / Source To switch your TV to standby mode. To select input from external sources. Subtitle On/Off Freeze Picture To enable the displaying of subtitles. To freeze the picture on the screen. TEXT button Mono-Stereo / Dual I-II To call up text services in analogue broadcasts and interactive services in digital mode. Stereo/Bilingual Transmissions To select TV programme number Direct number entry.
Connecting External Equipment Side View English Before connecting any external equipment, remove the mains plug from the wall socket. COMMON INTERFACE The Common Interface is for a Conditional Access Module (CAM). USB HDMI Input Sockets USB Input 5Vdc Max:500mA VGA Input ANT. (Aerial) Input SPDIF Coaxial Out +/- Controls P/V-AV Button SIDE AV Standby Button SIDE AV Input Headphone SCART Socket * a decoder could be Digital Satellite, Free to Air or any other compatible decoder.
Connecting an HDMI® or DVI Device to the HDMI Input English This input is designed to accept HDCP (High-Bandwidth Digital-Content Protection) programme material in digital form from EIA/CEA-861-D–compliant [1] consumer electronic devices (such as a set-top box or DVD player with HDMI or DVI output). NOTE: • Some early HDMI equipment may not work properly with your latest HDMI TV. • Supported Audio format: Linear PCM, sampling rate 32/44.1/48kHz.
Connecting a Computer USB MEMORY... To Connect a Computer To Connect a USB Disk With either an RGB/PC or an HDMI connection, you can watch your computer’s display on the television and hear the sound from the television’s speakers. • You can connect a USB disk to your TV by using the USB input of the TV. This feature allows you to display/play music, photo or video files stored in a USB stick.
Power Save Mode English Environmental Information • This television is designed to consume less energy to save environment. • You not only help to save the environment but also you can save money by reducing electricity bills thanks to the energy efficiency feature of this TV. To reduce energy consumption, you should take the following steps: • You can use Power Save Mode setting, located in the Feature menu.
Controlling the TV English A wide variety of external equipment can be connected via the sockets located on the side and back of the television. Whilst all the necessary adjustments and controls for the television are made using the remote control, the buttons on the left side of the television may be used for some functions.
Initial Installation English Before switching on the television put your decoder and media recorder to Standby if they are connected and ensure the aerial is connected to your television. To set up the television use the buttons on the remote control as detailed on page 8. IMPORTANT: Ensure that the aerial or cable is connected and a Common Interface module is not inserted before switching on the TV for the first time installation. 1.
Initial Installation - continued Auto Tuning English Auto Tuning As new services are broadcast, it will be necessary to retune the television in order to view them. • Auto Tuning will completely retune the television and can be used to update the channel list. It is recommended that Auto Tuning is run periodically to ensure that all new services are added. All current channels and settings, i.e. locked channels, will be lost. Note: You can press MENU button to cancel.
Manual Tuning, Analogue Fine Tuning The television can be tuned-in manually using Manual Search feature. English Digital Aerial Manual Search Analogue Manual Search The feature is available for service engineers or can be used for direct channel entry if the multiplex channel is known. The television can be tuned-in manually. For example: if the television cannot be connected to a media recorder/decoder with a SCART lead or to tune-in a station on another System.
General Operation English Stereo and Bilingual Transmissions Viewing Main Menu If stereo or dual language broadcasts are transmitted, the word Stereo or Dual will appear on the screen each time positions are changed, disappearing after a few seconds. If the broadcast is not in stereo, the word Mono will appear. • Press MENU button on the remote control to view main menu. Stereo… Press Volume to select Stereo or Mono. Bilingual… Bilingual transmissions are rare.
Channel List, Sorting Programmes, Programme Locking English You can view stored channels and sort them by using the Channel List feature. Viewing Channel List Deleting a Channel The channel order may be changed to suit your personal preference. You can press GREEN button to tag/untag all channels; YELLOW button to tag/untag channel. • Select Channel List from the main menu and press OK. The following menu will be displayed: • Select the channel that you want to delete and select Delete option.
Viewing Info Banner, Electronic Programme Guide English Viewing Info Banner • Press GREEN button to list the schedule. • Press i+ button the information screen will appear giving details of the channel and programme currently being viewed. • Press BLUE button to display filtering options. Note: There are alternative views of EPG screen. Button functions will be displayed at the bottom of the menu screen.
Language Selection English Language Settings Using this menu you can adjust the preferred language settings. • Select Language from Setup menu and press OK to view this menu. Press the RETURN button on the remote control to exit. Preferred These settings will be used if available. Otherwise the current settings will be used. Audio: by pressing Left or Right keys change the audio language. Subtitle: alter the subtitle language with Left or Right keys. The chosen language will be seen in subtitles.
Digital Settings - Parental Control, Menu Lock, Set PIN English You can view or set parental preferences of your TV. Viewing Parental Control Menu Maturity Lock (*) Press MENU button and select the Settings by using Left or Right button. Press OK button to view Settings menu. Use Up or Down button to highlight Parental and press OK to continue: Press MENU button and select settings by using Left or Right button. Press OK to continue. Use Up or Down to select parental and then press OK to continue.
Configuring Picture Settings English You can configure picture settings of your TV by using Picture Settings menu. Configuring Picture Settings Brightness You can use different picture settings in detail. You can customize current picture mode settings as desired. For example you change items such as, Brightness, Contrast, Colour, Sharpness and Hue. Press MENU button and select picture by using Left or Right button. Press Up or Down to select brightness. Sets the brightness value for the screen.
Configuring Picture Settings - continued English Noise Reduction Press MENU button and select picture by using Left or Right button. Press Up or Down to select noise reduction. Sometimes some words or picture elements to become distorted or pixelated. Using the Noise Reduction feature reduces this effect by smoothing out the edges. Picture Zoom Press MENU button and select picture by using Left or Right button. Press Up or Down to select picture zoom.
Changing Picture Format English Depending on the type of broadcast being transmitted, programmes can be viewed in a number of formats. Press the QUICK button and select Picture Zoom. Press OK repeatedly to select between auto, 16:9, subtitle, 14:9, 14:9 zoom, 4:3, panoramic or cinema. When Auto is selected the format being displayed is determined by the picture being broadcast. “Note: Using the special functions to change the size of the displayed image (i.e.
Configuring PC Picture Settings English You can set PC Mode picture settings when using the TV as a PC monitor. PC Picture Settings (*) H Position (*) While in VGA/PC mode, some items in Picture menu will be unavailable. Instead, VGA mode settings will be added to the Picture Settings while in VGA/ PC mode. H (Horizontal) Position shifts the image horizontally to right hand side or left hand side of the screen. PC Picture controls • Press the Left or Right button to adjust the value.
Configuring Sound Settings English You can configure sound settings of your TV by using Sound Settings menu. Configuring Sound Settings Sound settings can be configured according to your personal preferences. Press MENU button and select the Sound icon by using Left or Right button. Press OK button to view Sound Settings menu. In equalizer menu, the preset can be changed to Music, Movie, Speech, Flat, Classic and User. Press the MENU button to return to the previous menu.
Settings Menu Operation, Conditional Access English Configuring Your TV’s Settings Detailed settings can be configured to suit your personal preferences. Down to select timers and then press OK to continue. Using this menu you can adjust the preferred language settings. Sets timers for selected programmes. Date/Time Settings Viewing Settings Menu Press MENU button and select Settings icon by using Left or Right button. Press OK button to view Settings menu.
Setting Timers, Setting Date/Time English • The CAM should be correctly inserted, it is impossible to insert fully if reversed. The CAM or the TV terminal may be damaged if the CAM is forcefully inserted. Connect the TV to the mains supply, switch on and then wait for few moments until the card is activated. • When no module is inserted, “No Common Interface module detected” message appears on the screen. Date: Enter a date using the numeric buttons. Start: Enter a starting time using the numeric buttons.
Source Settings, Other Controls English Configuring Source Settings Configuring Other Settings - General You can enables or disable selected source options. The TV will not switch to the disabled source options button is pressed. when You can configure the settings of your TV. Select Configuration from Setup menu and press OK to view this menu. Press the RETURN button on the remote control to exit. To view general configuration preferences, select Other Settings in the Settings menu and press OK button.
Other Controls English Backlight Hard of Hearing This setting controls the backlight level. Select Backlight by pressing Up or Down button. Press Left or Right button to set Backlight to Auto, Medium, Maximum or Minimum. Note: Backlight adjustment is not available when Power Save mode is switched ON. Please see page 12 of this manual for explanation. Power Save Mode Use Up or Down button to select Power Save Mode. Press Left or Right button to set Power Save Mode as On or Off.
Other Controls - continued English Select Standby Search using Up or Down buttons and use Left or Right to set. If the Standby Search is set to to on and the TV is in standby mode, the TV will look for any changes in the saved channels. Full Mode (optional) If you connect a device via HDMI or YPbPr connectors and set 1080i/1080p resolutions, Full Mode item will be visible. TXT Language Press MENU button and select settings by using Left or Right button. Press OK to continue.
USB Media Browser English This TV allows you to enjoy photo, video or music files stored on a USB device. Manual Start • To display Media Browser window, you can press MENU button on the remote control and then select Media Browser by pressing Left or Right button. • Press OK button to continue. Media Browser menu contents (depending on the contents of your USB drive) will be displayed. Auto Start • When you plug a USB device, the following menu will be displayed.
USB Media Browser - continued This TV allows you to enjoy photo, video or music files stored on a USB device. English Viewing JPG Files Slideshow Feature To view photo files from a USB disk, you can use this menu screen. When you select Photos from Media Browser, available image files will be filtered and listed on this screen. You can use this feature to display photos on your TV. • Press RED button to zoom picture. • Press GREEN button to continue with the slideshow.
USB Media Browser - continued English This TV allows you to enjoy photo, video or music files stored on a USB device. Video Playback When you select Videos from Media Browser, available video files will be filtered and listed on this screen. You can use Up or Down button to select a video file and press OK button to play a video. the playback. Selected subtitles may not be displayed correctly in some cases. In order to display movie subtitles correctly, you should set a “Movie Subtitle” language.
Analogue Text Services Analogue Text Services Revealing Concealed Text Before using the text services, the required language region must be chosen. To discover the solutions on quiz and joke pages press the button. • Select Language from the SETTINGS menu. • Press the Left or Right button to choose the required language region. • After the teletext language is selected, press MENU button to exit. English This television has a multi-page text memory, which takes a few moments to load.
Appendix A: PC Input Typical Display Modes English The display has a maximum resolution of 1360 x 768. The following table is an illustration of some of the typical video display modes. Your TV may not support different resolutions. Supported resolution modes are listed below. If you switch your PC to an unsupported mode, a warning OSD will appear on the screen.
Appendix B: AV and HDMI Signal Compatibility (Input Signal Types) EXT (SCART) SIDE AV YPbPr HDMI1 HDMI2 Supported Signals Available PAL 50/60 O NTSC 60 O RGB 50 O RGB 60 O PAL 50/60 O NTSC 60 English Source O 480i 60Hz O 480p 60Hz O 576i 50Hz O 576p 50Hz O 720p 50Hz O 720p 60Hz O 1080i 50Hz O 1080i 60Hz O 1080p 50Hz O 1080p 60Hz O 480i 60Hz O 480p 60Hz O 576i 50Hz O 576p 50Hz O 720p 50Hz O 720p 60Hz O 1080i 50Hz O 1080i 60Hz O 1080p
Appendix C: Supported File Formats for USB Mode English Media Movie Music Remarks Format File Extension Video Audio (Maximum resolution/Bit rate etc.) MPEG1 MPEG Layer 1/2/3 MPEG2 MPEG2 .mpg/ .dat/ MPEG2-TS EAC3/ AC3 .vob/ mkv/ H.264-TS MPEG4 PCM/MP3 MS ISO PCM/MP3 MPEG4 .avi MJPEG PCM MPEG 1/2 .mp3 - 20Mbit/sec 20Mbit/sec Support SP and ASP 30fps@VGA Sample Rate: 8k ~ 48kHz, Layer 1/ 2/ Bit Rate: 128kbps~320kbps 3 (MP3) Photo .
Specifications and Accessories Broadcast Systems/Channels English DVB-T: MPEG2, DVB-T: MPEG4 HD DVB-C: MPEG2, DVB-C: MPEG4 Video Input PAL, SECAM, NTSC 4.
License Information English This product achieved the European Eco label award issued by the European Commission. You can get more information in following link: http://ec.europa.eu/environment/ecolabel/ For more information on the Eco-flower accreditation of our model range please refer to the advanced owners manual at the web site (www.toshiba-om.net).
Questions and Answers Questions and Answers English Below are the answers to some of the most common queries. For more information, go to www.toshiba.co.uk Q A Q A Q A Why is there no sound or picture? Check the television is not in standby mode. Check the mains plug and all mains connections. Why is there a picture but no sound? Check the volume has not been turned down or that sound mute has not been selected. What can cause a poor picture? Interference or a weak signal.
Questions and Answers English Below are the answers to some of the most common queries. For more information go to www.toshiba.co.uk Q A Q A Q A Why doesn't the Media Browser feature operate? Make sure that USB is connected correctly. Incorrect behaviour may occur with a USB Hub connection. Why is the digital channel locked? Parental control is activated. Check parental settings. Why are some encrypted digital channels unavailable? Your subscription needs upgrading. Contact your service provider.
If you wish to view the advanced functions but do not have access to a computer or the internet then please contact your nearest owner's manual Helpline number from the numbers shown below.
