Operation Manual

53
PC connection
As PCs are sometimes supplied with a ‘conventional’ CRT monitor, you may need to adjust the display
settings of your PC’s graphics card, otherwise the pictures may not appear correctly. Switch on your PC (still
with your original monitor) - select ‘1360 x 768’ for the screen resolution, and select 60 Hz for the on-screen
refresh rate. Switch off your PC, then connect it to your LCD TV while both items are still switched off.
Use a PC-VGA cable (not supplied) to connect the LCD-Monitor
to your PC. You can also connect the PC with HDMI cable. If
you use HDMI cable, you don’t have to connect the audio cable.
If you use HDMI-to-DVI cable, please connect audio cable as
same way as VGA cable. Make the connections carefully so as
not to break or bend the contacts inside the plug.
Select PC input
Switch on the LCD-TV.
Select the PC input mode (see page 11).
(When you use HDMI cable, select HDMI
input mode.)
Note:
If there is no video signal from the
computer when the unit is in PC
mode, “NO SIGNAL” will appear on
the TV screen.
Digital PC connection via HDMI input
is not supported.
If you try to connect your PC digitally
anyway, the TV-operation might
freeze. TV will stop to respond
properly on usercommands.
Countermeasure: Switch-off
your TV and disconnect from the
220~240V power-supply.
Disconnect the digital PC connection.
Now you may retry operating your TV.
If a digital PC connection does show
a picture, proper working is not
guaranteed. Digital PC connection is
not granted for this TV.
•
•
•
Description about the each setting option:
PICTURE Menu
BRIGHTNESS and CONTRAST: You can adjust these
according to your personal preferences.
HOR POSITION and VER POSITION: To adjust the
horizontal and vertical placing of the image.
PHASE and CLOCK: Eliminates the horizontal (PHASE)
and vertical (CLOCK) interfering lines.
RED/GREEN/BLUE: Influences the colour balance.
BACKLIGHT: Press ◀ or ▶ to adjust the level you require.
WXGA INPUT: When you input an WXGA signal, set this
option to “ON”.
RESET: Press ENTER to reset BRIGHTNESS,
CONTRAST, RED, GREEN, BLUE and BACKLIGHT to the
factory preset values.
AUDIO Menu
BASS/TREBLE/BALANCE: Tone setting
menu.
SURROUND (26DV615DG): Press ◀ or ▶ to
select surround sound feature ON or OFF.
RESET: Press ENTER to reset BASS,
TREBLE and BALANCE to the factory preset
values.
Example: Adjust the contrast.
1
During PC mode press MENU.
The Menu will appear on the screen.
BRIGHTNESS 25
CONTRAST 40
HOR POSITION 0
VER POSITION
PHASE 25
CLOCK
0
0
2
Select CONTRAST, then press
ENTER. Press ◀ or ▶ to adjust
CONTRAST.
3
Press EXIT to return to the normal screen.
VGA cable
(not supplied)
Audio cable
(not supplied)
PC
TV (Back side view)
to PC/HDMI1
AUDIO input
Monitor Display modes
MODE Resolution V. Frequency H. Frequency Pixel Clock Frequency
VGA 640 x 480 60.000Hz 31.500kHz 25.200MHz
SVGA 800 x 600 60.317Hz 37.879kHz 40.000MHz
XGA 1024 x 768 60.004Hz 48.363kHz 65.000MHz
WXGA 1280 x 720 59.870Hz 47.776kHz 79.500MHz
WXGA 1280 x 768 59.939Hz 44.955kHz 74.175MHz
WXGA 1360 x 768 60.015Hz 47.712kHz 85.5000MHz
(according to Graphic card)
to HDMI
input
to DVI
output
or
52R0131A_ENG.indd 5352R0131A_ENG.indd 53 4/3/09 11:09:00 AM4/3/09 11:09:00 AM