IPCN064 Access Point Operation Manual All other product names and trademarks in this document are trademarks of their respective companies.
Access Point User’s Manual No part of this publication may be reproduced in any form by any means without the prior written permission. Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies. 2003/07/09 Rev:01 Safety Notes For Installation n Use only the type of power source indicated on the marking labels. n Use only the power adapter supplied with the product.
Contents Chapter 1: Introduction ....................................................................................................................................................... 1 Unpacking ................................................................................................................................................................ 1 Chapter 2: Hardware Connection .........................................................................................................................
Access Point User’s Manual iv
Chapter 1: Introduction Chapter 1: Introduction IPCN064, a base station, functions as a bridge among a router/gateway and computers. Through the Access Point, any client (like notebook or PDA) with a wireless network card installed can connect to a host by air to access into Internet easily. Unpacking Check the contents of the package against the pack contents checklist below. If any of the items is missing, then contact the dealer from whom the equipment was purchased.
Access Point User’s Manual 2
Chapter 2: Hardware Connection Chapter 2: Hardware Connection LAN Connection Attach one end of the Ethernet cable with RJ-45 connector to the LAN port on a router or gateway, and the other end to the client station directly or through a hub. Wireless Connection Insert the wireless LAN card to the client station. Refer to the documentation of your wireless LAN card for instructions.
Access Point User’s Manual 4
Chapter 3: Configuring the Access Point via Web Browser Chapter 3: Configuring the Access Point via Web Browser Setting up a Host PC To configure the Access Point via web browser, at least one properly-configured PC must be connected to the network (either connected directly or through an external hub to the LAN port of the device). The host PC must meet the following requirements: l With Ethernet network interface. l Must have TCP/IP installed. l With a web browser installed: Internet Explorer 5.
Access Point User’s Manual Home Page The Access Point comes with the default IP address of 192.168.1.20 and subnet mask of 255.255.255.0. The home page of this Access Point is shown as above. Status This is the web page for the System Status. It lists the wireless and network settings currently for this Access Point.
Chapter 3: Configuring the Access Point via Web Browser Change the User Name and Password You might want to change the username and password for some reason. Please open Configuration – Administration web page to change it as you desired. Username You can change the username for your necessity. Please type in the new username on this box. Password Please enter the new password on this box. Re-enter Password You have to retype the new password on this box for confirmation.
Access Point User’s Manual Update the Firmware The Access Point supports the upgrading by using HTTP. To update the firmware that you get from your distributor, please open Configuration – Firmware Update web page. Follow the steps below: 1. Download and unzip the new software file from vendor. 2. In the Locate New Firmware field, click Browse to locate the upgrade file. 3. Click the Upgrade button. .
Appendix: Specifications Appendix: Specifications Frequency and Modulation Frequency band 5.15 to 5.25 GHz (MKK/Japan) 5.15 to 5.35, 5.725 to 5.825 GHz (FCC) Wireless Medium Transmit Power Range and Throughput Distance Range (Indoor) (Estimate) Distance Range (Outdoor) (Estimate) Network Standard Wireless Speed Ethernet Speed Architecture SSID 5GHz U-NII (OFDM) 16dbm @ 6 Mbps 13dbm @ 54 Mbps 54 Mbps @ 40 feet (10m) 6 Mbps @ 300 feet (90m) 54 Mbps @ 100 feet (30m) 6 Mbps @ 1000 feet (300m) IEEE 802.
Access Point User’s Manual United States FCC Part15 Physical Characteristics Ethernet Port 10/100 Base-T (RJ-45) with MDI-X auto crossover LED(s) Status (Green, Blue) LEDs, Ethernet Green LED Default Button Hold the button until green LED blinking. The system configuration will reset to default and reboot PWB 77 x 78 mm Dimensions 10 Housing 88mm(L) x 88mm(W) x 29mm(H) (±0.2mm) Black housing with black cable 2651mm(±70mm) TORX screw type used.
Appendix: Specifications 000510w-rt 11