TOSHIBA Wireless UWB Port Replicator Users Guide Version 0.
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1 CONTENTS : RIGHTS ................................................................................................................................................................................2 INTRODUCTION .................................................................................................................................................................4 1 TOSHIBA WIRELESS UWB PORT REPLICATOR FEATURES .............................
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1, Rights Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. WiQuest™ and WiDV™ are registered trademarks of WiQuest Communications, Inc.. No right, license, or interest to such trademark is granted hereunder.
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1, Regulatory Notices This equipment may only be operated indoors. Operation outdoors is in violation of 47 U.S.C. 301 and could subject the operator to serious legal penalties. THIS DEVICE MUST BE INSTALLED IN A LOCATION THAT IS NOT ACCESIBLE TO THE GENERAL PUBLIC. INSTALL THE DEVICE SO THAT THE ANTENNA IS MORE THAN 20 cm FROM UNSUSPECTING PERSONNEL.
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1, Introduction This document outlines how to install the WiQuest USB drivers and software of the TOSHIBA Wireless UWB Port Replicator. One of the most important parts of this document is the driver and software installation procedure. Make sure to follow the stepby-step procedures. These procedures are proven to work. If followed, the setup, installation, and evaluation will go smoothly.
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1, 2.1 Installing the Driver NOTE: From a driver perspective, the Wireless USB Hub represents two separate and unique USB devices. At least two drivers must be installed on the PC. The installed driver is tied to a PC’s particular USB port, so you will need to install the drivers for each port where the Wireless USB Hub might be installed. 2.
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1, Figure 1 - Select Setup Language Step 2 The WiQuest EVK Control Center Setup wizard will start as shown in shown in Figure 2 - Setup . Note: It is recommended that all user applications be closed while running the install shield; this will ensure that any open work is not unexpectedly closed or destroyed. Click “Next” to continue with the install process.
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1, Once the “I accept the agreement” radio button is selected, click “Next” to continue the setup. Figure 3 - Accept License Agreement Step 4 The install wizard allows you to select where to install the WiQuest EVK Control Center and driver files. If desired, change the installation directory and click “Next” to continue the installation.
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1, Figure 5 - Select Start Menu Folder Step 6 The install wizard allows you to create desktop and quick launch icons. The desktop and quick launch icons will allow the user to quickly start the ECC application. Select both and click “Next” to continue. Figure 8 - Select Additional Tasks Step 8 The next window shows the destination location for the installation, as well as the components and installation tasks indicated in the previous steps.
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1, Figure 9 - Ready to Install The installer will now install the application and copy the necessary drivers to the installation directory. This may take a few minutes. Step 9 Once the driver has finished installing the EVK Control Center, click “Finish” to exit the installer. Figure 6 - Click Finish to exit the installer.
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1, 2.3 Connect the TOSHIBA Wireless UWB Port Replicator hardware After installing the drivers and software, it is now time to install the hardware. Plug the TOSHIBA Wireless UWB PORT REPLICATOR into a USB port on the PC. The PC will make a sound indicating the detection of new hardware and will display a dialog box for installing the new hardware. Select “No, not this time” if it asks to connect to live update for the driver.
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1, Figure 13- Don't search, I will choose the driver to install Select “Toshiba WQST100 WiDV Source/HWA WUSB Device” when it asks the 2nd time for the device driver to install. Click “next” to continue.
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1, When it says “Completing the Found New Hardware Wizard,” select “finish.” Figure 9 - Click finish to complete installing the driver The driver is installed according to a procedure similar as for the following devices.
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1, Figure 16 – Target Menu 3.2.1 Select the Device Identifier (Address) and Time Frequency Code # EVK Control center supports changing the Device Identifier and Time Frequency Code (TFC#). Select Target -> Properties from the main window to see current setting and to change it. By default, most units are configured with a device identifier of “café" and a TFC of 6. To change the TFC, type in the desired value and click apply.
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1, 3.2.2 Receive Window The receive window displays information on all received packets. If you have two TOSHIBA WIRELESS UWB PORT REPLICATOR devices, or another WQST110 or WQST110-based device, you can use this window to configure the receiving device (MUST BE INSTALLED ON A SEPARATE PC). Figure illustrates the features and functions of the Receive Window. The receive window is split up into different sections.
TOSHIBA Wireless UWB Port Replicator Users Guide Revision 0.1, RX Settings 1. Receive Stream # - The active receive stream number. 2. Rx Mode - For the selected receive stream, the receiver can be placed into different verification modes. a. Basic Verification - All received frames have their FCS value verified. b. Fw CRC Verification -All received frames have their firmware computed checksum verified. This is in addition to the basic verification. 3.
