libretto U100 TOSHIBA libretto U100 Portable Personal Computer User’s Manual
User’s Manual Copyright © 2005 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
User’s Manual FCC information Product Name : libretto U100 Model number : PLU10 FCC notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
User’s Manual Telephone: (949) 583-3000 EU Declaration of Conformity TOSHIBA declares, that the product: PLU10* conforms to the following Standards: Supplementary “The product complies with the Information: requirements of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.” This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
User’s Manual Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.
User’s Manual One of the labels is located on the module.
User’s Manual Type of service Your modem is designed to be used on standard-device telephone lines. Connection to telephone company-provided coin service (central office implemented systems) is prohibited. Connection to party lines service is subject to state tariffs. If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request.
User’s Manual Instructions for IC CS-03 certified equipment 1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
User’s Manual Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non-compliant manner.
User’s Manual ■ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem.
User’s Manual ■ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired. ■ It is recommended that this equipment be disconnected from the Telecom line during electrical storms.
User’s Manual Optical disc drive safety instructions Be sure to check the international precautions at the end of this section. Panasonic DVD-ROM&CD-R/RW UJDA765 ■ The DVD-ROM&CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
User’s Manual DVD Super Multi UJ-822 ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■ To prevent direct exposure to the laser beam, do not try to open the enclosure.
User’s Manual International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
User’s Manual OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
User’s Manual xvi User’s Manual
libretto U100 Table of Contents Preface Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xxv Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxvi Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xxvi Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xxvi Keys. . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Optical media drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Region codes for DVD drives and media . . . . . . . . . . . . . . . . . . . . Writable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DVDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Formats . . . . . .
Table of Contents Using the USB floppy disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Connecting USB floppy disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 Disconnecting USB floppy disk drive . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 Using optical media drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Loading discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Removing discs . .
Table of Contents Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wireless LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bluetooth wireless technology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . BluetoothTM Stack for Windows® by TOSHIBA . . . . . . . . . . . . . . . Wireless communication switch . . . . . . . . . . . . . . . . . . . . . . . . . . . Wireless communication Indicator. . . . . . . . . . . . . . . .
Table of Contents Care and use of the battery pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 Charging the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8 Monitoring battery capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9 Maximizing battery operating time . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents libretto DVD Dock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front and Left side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Right side and Back side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting the libretto DVD Dock. . . . . . . . . . . . . . . . . . . . . . . . . . Disconnecting the libretto DVD Dock . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Non-applicable Icons*5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2 Wireless LAN/Atheros*6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 TV Tuner*7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 Images*8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 LCD Brightness and Eye Stain*9 . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents xxiv User’s Manual
libretto U100 Preface Congratulations on your purchase of the libretto U100 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your libretto U100 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Preface Chapter 4, Operating Basics, includes instructions on using the following devices: Pointing Device, Fingerprint Sensor, USB floppy disk drive, optical media drives, sound system, modem, Wireless communication features, LAN. It also provides tips on care of the computer, floppy disks and CD/ DVDs. Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys.
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, CTRL + C means you must hold down CTRL and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
Preface xxviii User’s Manual
libretto U100 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Instruction Manual for Safety & Comfort.
General Precautions PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phone Use of mobile phones can interfere with the audio system. Computer operation is not impaired but it is recommended that a distance of 30 cm be maintained between the computer and a mobile phone in use.
libretto U100 Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction Software Microsoft® Windows XP Professional ■ The following software is preinstalled: ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Microsoft® Windows XP Professional Microsoft Internet Explorer TOSHIBA Utilities TOSHIBA SD Memory Boot Utility DVD Video Player TOSHIBA Power Saver TOSHIBA Assist TOSHIBA ConfigFree TOSHIBA Zooming Utility TOSHIBA PC Diagnostic Tool TOSHIBA Virtual Sound TOSHIBA Controls Online manual Microsoft® Windows XP Home Edition ■ The following software is preinstalled: ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Introduction Documentation ■ libretto U100 Portable Personal Computer User’s Manual ■ Microsoft Windows XP manual package ■ Instruction Manual for Safety & Comfort ■ End User License Agreement If any of the items are missing or damaged, contact your dealer immediately. Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability.
Introduction CPU performance may also vary from specifications due to design configuration. Under some conditions, your computer product may automatically shutdown. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium.
Introduction Disclaimer (Battery Life) Battery life may vary considerably depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Introduction libretto DVD Dock ■ The optical media drive is optional. ■ The optical media drive can be used by connecting libretto DVD Dock to this computer. 1-6 DVD-ROM&CD-R/RW drive Some models are equipped with a full-size, DVDROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at maximum 24 speed and CD-RW at maximum 24 speed.
Introduction Display The computer’s LCD display panel supports high-resolution video graphics. The LCD screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in*1 7.2” TFT LCD screen 16 M colors, with a resolution of 1280 horizontal × 768 vertical pixels WXGA. Disclaimer (LCD) Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology.
Introduction Universal Serial Bus (USB 2.0) The computer has Universal Serial Bus ports that comply with the USB 2.0 standard, which enables data transfer speeds 40 times faster than the USB 1.1 standard (The ports also support USB 1.1). Docking port This port enables connection of an optional libretto DVD Dock described in the Options section. i.LINK™ (IEEE1394) This port enables high-speed data transfer directly from external devices such as digital video cameras.
Introduction Communications User’s Manual Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to V.90 section in Appendix E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. It is preinstalled as a standard device in some markets. Both of V.90 and V.92 are supported only in USA, Canada and Australia. Only V.90 is available in other regions.
Introduction Wireless LAN Some computers in this series are equipped with a Wireless LAN mini-PCI card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision A or B or G). Refer to Wireless LAN section in Appendix F. ■ Theoretical maximum speed: 54Mbps (IEEE 802.11a/g) ■ Theoretical maximum speed: 11Mbps (IEEE802.11b) ■ Frequency Channel Selection (2.
Introduction Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. User’s Manual Hot keys Key combinations let you quickly change the system configuration directly from the keyboard without running a system configuration program. Display automatic power off This feature automatically cuts off power to the computer’s LCD display panel when there is no keyboard input for a time specified.
Introduction Battery save mode This feature lets you save battery power. You can specify the Power Save Mode in the Profile item in TOSHIBA Power Saver. Panel power on/off This feature turns power to the computer off when the computer’s LCD display panel is closed and turns it back on when the computer’s LCD display panel is opened. You can specify the setting in the When I close the lid item of the Setup Action tab in TOSHIBA Power Saver.
Introduction Hibernation This feature lets you turn off the power without exiting from your software. The contents of main memory are saved to the hard disk, when you turn on the power again, you can continue working right where you left off. Refer to the Turning off the power section in Chapter 3, Getting Started, for details. Standby If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory.
Introduction Fingerprint utility This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password to the fingerprint authentication device, it is no longer necessary to input the password from the keyboard. Just by swiping the finger against the fingerprint sensor, the following functions will be enabled: ■ Logon to Windows and access a securityenabled homepage through IE (Internet Explorer).
Introduction TOSHIBA PC Diagnostic Tool TOSHIBA PC Diagnostic Tool displays the basic information on PC, and the test of built-in devices can also be performed. To start TOSHIBA PC Diagnostic Tool, click start, point to All Programs, point to TOSHIBA, point to Utility and click PC Diagnostic Tool. Sound drivers A broad range of audio controls are available through the ADI sound driver, including Software Synthesize, Mic Volume, Noise Reduction and Audio Power Management.
Introduction TOSHIBA SD This utility has the function which formats SD Memory Card Format memory card by SD standard format. TOSHIBA Acoustic Silencer This utility has the function to set up the read speed of CD. It is ineffective in DVD. You can set up one of the modes: [Normal Mode] can read data early, and [Quiet Mode] can lessen noise. Options You can add a number of options to make your computer even more powerful and convenient to use.
Introduction User’s Manual Mobile HDD A mobile external hard disk drive that is compatible with USB2.0. Data can be read and written by connecting to the USB port of the computer. You can buy the module from TOSHIBA dealer. DVD-ROM&CD-R/RW drive DVD-ROM&CD-R/RW drive is available as an optional external optical disk drive. You can buy the drive from TOSHIBA dealer.
Introduction 1-18 User’s Manual
libretto U100 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer.*5 Disclaimer (Non-applicatable Icons) Certain notebook chassis are designed to accommodate all possible configurations for an entire product series.
The Grand Tour PC card eject lever This is a lever for taking out PC card from a PC card slot. i.LINK (IEEE1394) port Connect an external device, such as a digital video camera to this port for high-speed data transfer. System indicators LEDs let you monitor the status of various computer functions. Details are given in the System indicators section. Left side Figure 2-2 shows the computer’s left side.
The Grand Tour ■ Turn WiFi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any WiFi or Bluetooth functionality. ■ Always turn off WiFi or Bluetooth functionality if the PC is near automatic control equipment or appliances such as automatic doors or fire detectors.
The Grand Tour Volume control Use this dial to adjust the volume of the stereo speakers and the stereo headphones. Headphone jack A 3.5 mm mini headphone jack enables connection of stereo headphones. Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input. Universal Serial Bus (USB 2.0) port Two Universal Serial Bus ports are on the right side. The ports comply with the USB 2.
The Grand Tour LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX). Refer to Chapter 4, Operating Basics, for details. ■ Do not connect any cable other than a LAN cable to the LAN jack. It could cause damage or malfunction. ■ Do not connect the LAN cable to a power supply. It could cause damage or malfunction. Back side Figure 2-4 shows the computer’s back side.
The Grand Tour Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. Notches Battery lock Battery release latch Docking port Memory module cover Figure 2-5 The underside of the computer Battery lock Slide this lock to release the battery pack for removal. Battery release latch Slide and hold this latch to release the battery pack for removal.
The Grand Tour Notches Notches on the computer engage hooks on the libretto DVD Dock to hold the connection securely. Memory module cover This cover protects one memory module socket, one module is preinstalled. Refer to the Memory expansion section in Chapter 8, Optional Devices. Front with the display open This section shows the front of the computer with the LCD display panel open. Refer to the appropriate illustration for details. To open the LCD display panel lift up.
The Grand Tour Display hinge The display hinge holds the LCD display panel at easy-to-view angles. LCD screen The LCD screen displays high-contrast text and graphics. The computer’s WXGA screen consists of 1280 × 768 pixels. Refer to Display Controller and Modes in Appendix B. When the computer operates on the AC adaptor the LCD screen’s image will be somewhat brighter than when it operates on battery power. The lower brightness level is intended to save battery power.
The Grand Tour Fingerprint Sensor Just by swiping the finger against the fingerprint sensor, the following functions will be enabled: ■ Logon to Windows and access a securityenabled homepage through IE (Internet Explorer). ■ Files and folders can be encrypted/decrypted and third party access to them prevented. ■ Disable the password-protected screen-saver when returning from power-saving (standby) mode. Power button Press the power button to turn the computer’s power on and off.
The Grand Tour Wireless communication The Wireless communication indicator glows when the Wireless LAN and Bluetooth functions are turned on. Some models are equipped with a Wireless communication. USB floppy disk drive USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks. It connects to the USB port. Option or provided with some models.
The Grand Tour Optical media drives ■ The optical media drive is optional. ■ The optical media drive can be used by connecting libretto DVD Dock to this computer. One of the following optical media drives is installed in the computer: DVDROM&CD-R/RW and DVD Super Multi drives. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows.
The Grand Tour Writable discs This section describes the types of writable CD/DVD discs. Check the specifications for your drive to for the type of discs it can write. Use RecordNow! to write compact discs. Refer to Chapter 4, Operating Basics. CDs ■ CD-R discs can be written only once. The recorded data cannot be erased or changed. ■ CD-RW discs including multi speed CD-RW discs, high-speed CD-RW discs, ultra-speed CD-RW discs can be recorded more than once.
The Grand Tour DVD Super Multi drive The full-size DVD Super Multi drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge. DVD read 8 speed (maximum) DVD-R write 2 speed (maximum) DVD-RW write 2 speed (maximum) DVD+R write 2.4 speed (maximum) DVD+RW write 2.
The Grand Tour Figure 2-10 The AC adaptor (3-pin plug) ■ The Universal AC Adaptor and power cord bundled with this product may differ depending on the product model. Depending on the model, a 2-pin plug or 3-pin plug set of the above may be bundled. ■ Do not use a 3-pin to 2-pin conversion plug. ■ The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region.
libretto U100 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Select a work area that has: ■ a well-designed and functioning ventilation system that does not forcefully direct air on you ■ good air circulation ■ a comfortable ambient temperature and relative humidity.
Getting Started ■ Leave ample ventilation room for the fan. Do not block the vents. ■ If the PC interferes with radio equipment, turn the PC power off immediately. Such interference could cause equipment malfunction. ■ Never place your PC on a shaky table, uneven, tilted surface or other unstable location. Your PC may fall, causing damage to the PC or possibly injury. ■ Never leave the power to your PC on continuously for more than 24 hours. Turn the power off when this product is not in use.
Getting Started Seating and posture Maintain a comfortable working posture when using your PC where your body joints are naturally aligned to reduce stress on different parts of your body. Consider the following: Below eye level 90°angles Foot rest Figure 3-1 Posture and positioning of the computer ■ Keep hands, wrists, and forearms straight, in-line and roughly parallel to the floor. ■ Keep head level, or bent slightly forward, forward facing, and balanced.
Getting Started Consider the following suggestions regarding lighting your work environment: ■ Position the PC so that the light source does not shine or reflect directly onto the display or shine or reflect directly into the eyes of the user. ■ Shield the PC from direct light by using tinted windows or by installing blinds or a screen. ■ Use soft, indirect lighting. ■ Adjust the display panel to provide maximum visibility.
Getting Started Other Things to Note ■ Never turn off the power while an application is running. Doing so could cause loss of data. ■ Use a virus-check program and make sure it is updated regularly. ■ Never turn off the power, disconnect an external storage device or remove storage media during data read/write. Doing so can cause data loss. ■ Never format storage media without checking its content. Formatting destroys all stored data.
Getting Started ■ The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region. For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region. ■ Do not use a 3-pin to 2-pin conversion plug. ■ When you connect the AC adaptor to the computer, always follow the steps in the exact order as described in the User’s Manual.
Getting Started 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the left of the computer. DC IN 15V jack Figure 3-4 Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow. Opening the display The computer’s LCD display panel can be rotated in a wide range of angles for optimal viewing. 1.
Getting Started Turning on the power This section describes how to turn on the power. The Power LED indicates the status. Refer to the Power indicator section in Chapter 6, Power and Power-Up Modes. ■ After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Starting up for the first time. ■ If the USB floppy disk drive is connected, make sure it is empty.
Getting Started Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen. 1. If you have entered data, save it to the hard disk or to a floppy disk. 2. Make sure all disk (disc) activity has stopped, then remove the CD/ DVDs or floppy disk. ■ Make sure the HDD indicator is off. If you turn off the power while a disk (disc) is being accessed, you can lose data or damage the disk (disc).
Getting Started For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places: the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver. Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby mode will be lost. ■ You can return to your previous working environment immediately when you turn on the computer.
Getting Started Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Standby mode If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off. ■ When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility.
Getting Started Executing standby You can also enable Standby by pressing FN + F3. See Chapter 5, The Keyboard, for details. You can enter standby mode in one of three ways: 1. Click start, click Turn Off Computer and click Stand By. 2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver. 3. Press the power button.
Getting Started Creating the Optical Recovery Discs ■ A writable external optical media drive that is sold separately and compatible to the computer is required to create the Recovery Discs. It can be purchased from TOSHIBA dealers.
Getting Started 4. Insert the (first) blank media into the tray of the Optical Drive. 5. Double click the Recovery Disc Creator Launcher icon on the Windows XP desktop, or Select the application from start Menu. 6. After Recovery Disc Creator starts, select the type of media and the title you wish to copy to the media then click the Burn button. ■ If your Optical Drive can only write to CDs, select "CD" as the "Type" on Recovery Disc Creator.
Getting Started Restoring the preinstalled software from your creating Recovery Media ■ A external optical media drive that is sold separately and compatible to the computer is required to create the Recovery Discs. It can be purchased from TOSHIBA dealers.
libretto U100 Chapter 4 Operating Basics This chapter gives information on basic operations including using the TOSHIBA Pointing Device, the Fingerprint Sensor, the USB floppy disk drive, optical media drives, Sound System, Modem, Wireless communication features, LAN and Hard Disk Drive (HDD) protection. It also provides tips on care of the computer, floppy disks and CD/DVDs. TOSHIBA Pointing Device The computer is equipped with a point system: an AccuPoint pointing stick.
Operating Basics Using the AccuPoint To use the AccuPoint, simply push it with your finger tip in the direction you want to move the on-screen pointer. Two buttons above the Touch Pad work in the same way with the AccuPoint as they do with the Touch Pad. Two buttons below the AccuPoint are used like the buttons on a mouse pointer. Press the left button to select a menu item or to manipulate text or graphics designated by the pointer.
Operating Basics Replacing the cap The AccuPoint cap is an expendable item that should be replaced after prolonged use. The spare AccuPoint cap is supplied with the computer. 1. To remove the AccuPoint cap, firmly pinch the cap and pull it straight up. Figure 4-2 Removing the AccuPoint cap 2. Position a new cap on the peg and press it into place. The peg is square, so be careful to align the cap’s square hole with the peg.
Operating Basics Points to note about the Fingerprint Sensor Failure to follow these guidelines might result in (1) damage to the sensor or cause sensor failure, (2) finger recognition problems, or lower finger recognition success rate. ■ Do not scratch or poke the sensor with your nails or any hard or sharp objects. ■ Do not press the sensor strongly. ■ Do not touch the sensor with a wet finger or any wet objects. Keep sensor surface dry and free of water vapor.
Operating Basics ■ Check sliding position and speed (see the drawing below). Fingerprint Sensor Limitations. ■ The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. ■ A warning message will be displayed when recognition is abnormal or recognition is not successful within a fixed duration. ■ The recognition success rate may differ from user to user. ■ Toshiba does not guarantee that this fingerprint recognition technology will be error-free.
Operating Basics In the help file, it is stated that this software's Password Replacement function can be used for the Internet and general applications. However, the Internet Password Replacement function in the fingerprint utility provided in this computer can only be used with IE (Internet Explorer). There is a section on Strong Logon Security in the help file, but the function is not available in the fingerprint utility provided in this computer.
Operating Basics We recommend first-timers to click Practice, and then swipe the finger as a practice. 5. The Capture Fingerprint screen is displayed. Follow the onscreen instructions and use the same finger you have selected under Choose Finger to swipe three times to allow the sensor to read the fingerprint. The fingerprint will be shown in green if properly read, or in red if the reading is abnormal. 6. The Verify Fingerprint screen is displayed. Swipe the finger again to allow the sensor to read again.
Operating Basics How the Swipe the Finger Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures: 1. Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you. While lightly touching the sensor, swipe the finger towards you until the sensor surface becomes visible. Ensure the center of the fingerprint is on the sensor when swiping the finger. 2.
Operating Basics Connecting USB floppy disk drive To connect the drive, plug the floppy disk drive’s USB connector into a computer’s USB port. Refer to Figure 4-3. Make sure the connector is right side up and properly aligned with the socket. Do not try to force the connection, doing so can damage the connecting pins.
Operating Basics Using optical media drives ■ The optical media drive is optional. ■ The optical media drive can be used by connecting libretto DVD Dock to this computer. ■ Please ensure that it is used on a flat surface such as a table when a CD/DVD is used to connect to the libretto DVD Dock. If used when placed on an unstable location or if strong vibrations shake it during operation, the CD/DVD might be scratched and the drive might be damaged.
Operating Basics Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-4 to 4-7. 1. When the computer’s power is on, press the eject button to open the disc tray slightly. Eject button Figure 4-4 Pressing the eject button 2. Grasp the disc tray gently and pull until it is fully opened.
Operating Basics 3. Lay the CD/DVD, label side up, in the disc tray. Laser lens Figure 4-6 Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure 4-6. ■ Do not touch a laser lens and its circumference portion. Doing so could cause misalignment.
Operating Basics 5. Push the center of the disc tray to close it. Press gently until it locks into place. ■ Always keep fingers away from the sides of the tray when closing the tray of an optical drive (CD/DVD drive, CD-RW drive, Multi-drive or equivalent drive) to avoid pinching your fingers. ■ If the CD/DVD is not seated properly when the disc tray is closed, the CD/DVD might be damaged. Also, the disc tray might not open fully when you press the eject button.
Operating Basics 2. The CD/DVD extends slightly over the sides of the disc tray so you can hold it. Hold the CD/DVD gently and lift it out. Figure 4-8 Removing a CD/DVD 3. Push the center of the disc tray to close it. Press gently until it locks into place. How to remove CD/DVD when the disk tray will not open Pressing the eject button will not open the disc tray when the computer power is off.
Operating Basics Writing CDs on DVD-ROM&CD-R/RW drive Depending on the type of drive installed, you may be able to write CDs. The DVD-ROM&CD-R/RW drive lets you write as well as read CD-ROMs. Observe the precautions in this section to ensure the best performance for writing CDs. For information on loading and unloading CDs refer to the Using optical media drives section. Refer to the Writable discs, Chapter 2 for the details about the types of writable CD/DVD discs.
Operating Basics TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ The actual number of rewrites to CD-RW is affected by the quality of the disc and the way it is used. ■ Be sure to connect the AC adaptor when you write or rewrite. ■ Be sure to close all other software programs except the writing software. ■ Do not run software such as a screen saver which can put a heavy load on the CPU.
Operating Basics Writing CD/DVDs on DVD Super Multi drive You can use the DVD Super Multi drive to write data to either CD-R/RW or DVD-R/-RW/+R/+RW/-RAM discs. The following applications for writing are preinstalled: RecordNow!, and DLA licensed by Sonic Solutions. InterVideo WinDVD Creator 2 Platinum, which is a product of InterVideo, Inc. Refer to the Writable discs, Chapter 2 for the details about the types of writable CD/DVD discs.
Operating Basics Before writing or rewriting ■ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYO YUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: (Multi-Speed and High-Speed) MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd.
Operating Basics DVD+RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.0 or Version 2.1 Matsushita Electric Industrial Co., Ltd. Hitachi Maxell Ltd. This drive cannot use discs that allow writing faster than 8 speed (DVD-R, DVD+R), 4 speed (DVD-RW, DVD+RW), 3 speed (DVD-RAM). ■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it.
Operating Basics ■ Be sure to close all other software programs except the writing software. ■ Do not run software such as a screen saver, which can put a heavy load on the CPU. ■ Operate the computer in the full-power mode. Do not use power-saving features. ■ Do not write while virus check software is running. Wait for it to finish and then disable virus detection programs including any software that checks files automatically in the background.
Operating Basics RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■ DVD-Video cannot be created using RecordNow!. ■ DVD-Audio cannot be created using RecordNow!. ■ You cannot use RecordNow!'s “Audio CD for Car or Home CD Player” function to record music to the DVD-R/-RW or DVD+R/+RW disc. ■ Do not use the “Exact Copy” function of RecordNow! to copy DVDVideo and DVD-ROM with copyright protection.
Operating Basics Data Verification To verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD. 1. Click the Options button ( ) on the RecordNow! Console to open the Options panels. 2. Select the Data in the left-side menu. 3. Mark the Verify data written to the disc after burning check box in the Data Options. 4. Click the OK button.
Operating Basics 4. Click the Advanced tab in the System Properties window. 5. Click the Settings icon in the "Performance" section. 6. Click the Advanced tab in the Performance Options window. 7. Click the Change icon in the "virtual memory" section. 8. Select the Custom size button in the Virtual Memory window. 9. Specify much higher values for "Initial size" and "Maximum size." 10. Click the Set button in the Virtual Memory window. 11. Click the OK button in the Virtual Memory window.
Operating Basics ■ Do not change display settings while using WinDVD Creator. ■ Do not enter standby/hibernation mode while using WinDVD Creator. ■ Do not operate WinDVD Creator immediately after turning on the computer. Please wait until all Disc Drive activity has stopped. ■ When recording to a DV-Camcorder, to ensure you capture all of your data, let the camcorder record for a few seconds before you begin recording your actual data.
Operating Basics 3. About Disc Manager ■ WinDVD Creator can edit one play list on a disc. ■ WinDVD Creator might show a different a thumbnail than you previously set in CE (Consumer Electronics) DVD-RAM recorder. ■ Using the Disc Manager, you can edit DVD-VR format on DVDRAM, DVD+VR format on DVD+RW, and DVD-Video format on DVD-RW. 4. About recorded DVDs ■ Some DVD-ROM drives for personal computers or other DVD players may not be able to read DVD-R/+R/-RW/+RW/-RAM discs.
Operating Basics Floppy disks 1. Store your floppy disks in the container they came in to protect them and keep them clean. If a floppy disk is dirty, do not use cleaning fluid. Clean it with a soft damp cloth. 2. Never open the shutter or touch the magnetic surface of your floppy disk. You could permanently damage it and lose data. 3. Always handle floppy disks with care, to prevent the loss of stored data. Always apply the floppy disk label in the correct location.
Operating Basics To adjust the volume or activate Mute, click start, point to All Programs, point to Accessories, point to Entertainment and click Volume control. In the Master volume panel, you can use the slide bars to adjust the volume level or click Mute at the bottom of the panel. SoundMAX control panel The SoundMAX control panel lets you control additional functions for the Microphone Enhancement and Audio Power Management. To launch the SoundMAX Control Panel, follow the steps below. 1.
Operating Basics Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack. ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■ Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX).
Operating Basics Properties menu Click the icon with the secondary mouse button to display properties menu on the screen. Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection.
Operating Basics Attaching the ferrite core to the modular cable The ferrite core that attaches to the modular cable bundled with this product is explained here. When connecting the modular cable, attaching the bundled ferrite core to the modular cable will help to reduce noise. To attach the ferrite core, follow the steps below. When attaching the ferrite core to the modular cable, please ensure that the cable is set in the dimpled portion of the ferrite core.
Operating Basics 3. Wind the modular cable around the ferrite core as in the diagram shown below. Wind the modular cable loosely one full round around the ferrite core. Please do not forcibly pull the modular cable when winding. Modular cable Figure 4-12 Furling the modular cable 4. Please ensure that the ferrite core is closed properly without the cable or connector stuck in between. Please close properly until the core is locked with a clicking sound.
Operating Basics ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■ Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX). ■ Never connect the built-in modem to a key telephone system for residences or offices.
Operating Basics Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices. All models are provided with Wireless Communication switch. Some models are equipped with Wireless LAN and Bluetooth functions. Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum /Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE802.
Operating Basics Security ■ Be sure to enable WEP (encryption) function. Otherwise your computer will allow the illegal access by outsider through Wireless LAN to cause illegal intrusion, eavesdropping, and loss or destruction of stored data. TOSHIBA strongly recommend the customer to enable the WEP function. ■ TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof.
Operating Basics Release Notes related to the BluetoothTM Stack for Windows® by TOSHIBA 1. Install: On Windows2000 or Windows XP, BluetoothTM Stack for Windows® by TOSHIBA does not need signature. 2. Fax application software: Regarding FAX application software, there are some software that you cannot use on this BluetoothTM Stack. 3. Multi User: On Windows XP, Multi user does not supported. When you use Bluetooth, you might not use Bluetooth another logon user.
Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.
Operating Basics Connecting LAN cable To connect the LAN cable, follow the steps below. ■ Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up. ■ Do not connect any other cable to the LAN jack except the LAN cable. Otherwise, malfunctions or damage may occur. ■ Do not connect any power supplying device to the LAN cable that is connected to the LAN jack.
Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again. ■ Clean the computer using a slightly damp (with water) cloth. You can use glass cleaner on the LCD display screen.
Operating Basics Using the Hard Disk Drive (HDD) Protection There is a function for reducing the risk of damage on HDD in this computer. Using the acceleration sensor built in the computer, HDD Protection detects vibration, shocks and similar signs in the computer, and automatically moves the HDD head to a safe position in order to reduce the risk of damage that could be caused by a head-to-disk contact. ■ This function does not guarantee that the HDD will not be damaged.
Operating Basics TOSHIBA HDD Protection Properties You can make the HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start, point to All Programs, point to TOSHIBA, point to Utilities and click HDD Protection setting. The window can also be started from the icon on the Taskbar, or from the Control Panel. Figure 4-17 TOSHIBA HDD Protection Properties HDD Protection You can choose whether to enable or disable HDD Protection.
Operating Basics Different detection levels can be set depending on whether the computer is used as handheld or mobile usages, or whether it is used in a stable environment such as on a table in the workplace or at home. By setting different detection levels for the computer depending on whether it runs with the AC power (desktop) or with batteries (handheld or mobile usage), the detection level automatically switches according to the power connection mode.
Operating Basics Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. You can select whether to control the CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver.
libretto U100 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available.
The Keyboard Function keys: F1 … F12 The function keys (not to be confused with FN) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the FN key, keys marked with icons execute specific functions on the computer. Refer to the section, Soft keys: FN key combinations, in this chapter.
The Keyboard Press FN + F10 or FN + F11 to access the integrated keypad. When activated, the keys with gray markings on the upper surface become numeric keypad keys (FN + F11) or cursor control keys (FN + F10). Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for both settings is off. Press FN + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
The Keyboard Hot keys Hot keys (FN + a function or ESC key) let you enable or disable certain features of the computers. Sound mute: Pressing FN + ESC in a Windows environment turns sound on or off. When you press these hot keys, the current setting will change and be displayed as an icon. Instant security: Press FN + F1 to blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or press the AccuPoint.
The Keyboard Display selection: Press FN + F5 to change the active display device. When you press these hot keys, a dialog box appears. Only selectable devices will be displayed. Hold down FN and press F5 again to change the device. When you release FN and F5, the selected device will change. If you hold down these hot keys for five seconds the selection will return to the internal LCD. Internal LCD screen Brightness: Pressing FN + F6 decreases the LCD screen brightness in decrements.
The Keyboard If no wireless communication device is installed, no dialog box will appear. LCD screen resolution selection: Press FN + Space keys to change the LCD screen resolution. Each time when you press these hot keys, the LCD screen resolution changes as follows: With WXGA, you can change the resolution 800 × 600, 1024 × 768 and 1280 × 768 pixels. TOSHIBA Zooming Utility (reduce): To reduce the icon size on the desktop or the application window, press the 1 key while holding down the FN key.
The Keyboard Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one. The keys in the center of the keyboard with gray letters make up the numeric keypad overlay. The overlay provides the same functions as the numeric keypad on the 101/102-key enhanced keyboard in figure 5-2. Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control.
The Keyboard Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold FN and press any other key. All keys will operate as if the overlay were off. 2. Type upper-case characters by holding FN + SHIFT and pressing a character key. 3. Release FN to continue using the overlay.
libretto U100 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Table 6-1 Power conditions continued Power on AC adaptor not connected Battery charge is above low battery trigger point • Operates • LED: Battery off DC IN off Battery charge is below low battery trigger point • Operates • LED: Battery flashes orange DC IN off Battery charge is exhausted Computer goes into resume mode shuts down No battery installed • Cannot operate • LED: Battery off DC IN off Power off (no operation) Power indicators As shown in the above table, the Ba
Power and Power-Up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected: Green Indicates the AC adaptor is connected and supplying proper power to the computer. Flashing orange Indicates a problem with the power supply. Plug the AC adaptor into another power outlet. If it still does not operate properly, contact your dealer. No light Under any other conditions, the indicator does not light.
Power and Power-Up Modes ■ The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Always dispose of used battery packs in compliance with all applicable laws and regulations.
Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance. Safety precautions Mishandling of battery packs can cause death, serious injury or property damage.
Power and Power-Up Modes 7. Never allow a battery pack to become wet. A wet battery pack will overheat or ignite causing rupture or fire, possibly resulting in death or serious injury. 8. Never store a battery pack in an area of high humidity. This could cause a fire or explosion possibly resulting in serious injury. 9. Never expose a battery pack to abnormal shock, vibration or pressure.
Power and Power-Up Modes 15. Make sure the battery is securely installed in the computer before attempting to charge the battery pack. Improper installation could generate smoke or fire, or cause the battery pack to rupture. 16. Keep the battery pack out of reach of infants and children. It can cause injury. Caution 1. Never continue to use a battery pack after its recharging capacity has become impaired, or after the display of a warning message indicating that the battery pack’s power is exhausted.
Power and Power-Up Modes Charging the batteries When the power in the battery pack becomes low, the Battery indicator flashes orange indicating that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer enables Hibernation mode (so you don’t lose data) and automatically turns off.
Power and Power-Up Modes The Battery indicator may show a rapid decrease in battery operating time when you try to charge a battery under the following conditions: ■ The battery has not been used for a long time. ■ The battery has completely discharged and been left in the computer for a long time. ■ A cool battery is installed in a warm computer. In such case, follow the steps below. 1. Fully discharge the battery by leaving it in the computer with the power on until the power automatically shuts off. 2.
Power and Power-Up Modes Maximizing battery operating time A battery’s usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ■ How you configure the computer (for example, whether you enable battery-power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power.
Power and Power-Up Modes Extending battery life To maximize the life of your battery pack: ■ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below. 1. Turn off the computer’s power. 2. Disconnect the AC adaptor and turn on the computer’s power. If it does not turn on go to step 4. 3. Operate the computer on battery power for five minutes.
Power and Power-Up Modes ■ Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAM, so if the computer loses power it will be lost. ■ In Hibernation mode, data will be lost if you remove the battery pack or disconnect the AC adaptor before the save is completed. Wait for the HDD indicator to go out. ■ Do not touch the battery release latch while holding the computer. Or you may get injured by the dropped battery pack by unintentional release of the battery release latch.
Power and Power-Up Modes 8. Secure the battery pack lock. Check the battery lock (➁) was changed to the lock position ( ). Battery pack Battery lock Figure 6-2 Securing the battery pack 9. Return your computer to the upright position. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password.
Power and Power-Up Modes ■ After you set the password, a dialog box will be displayed asking whether you want to save it to a floppy disk or other media. If you forget the password, you can open the password file on another computer. Be sure to keep the media in a safe place. ■ When entering the character string to register the password, enter from the keyboard character by character and do not enter as ASCII code or copy-and-paste the character string.
Power and Power-Up Modes 3. Press ENTER. If you enter the password incorrectly three times in a row, the computer shuts off. In this case, you must turn the computer back on to retry password entry. Power-up modes The computer has the following power-up modes: ■ Boot: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode. ■ Hibernation: Data in memory is saved to the hard disk. ■ Standby: Data is maintained in the computer’s memory.
Power and Power-Up Modes 6-16 User’s Manual
libretto U100 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config and USB. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup.
HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you use the display to be used when the computer is booted.
HW Setup HDD −> FDD −> CDROM −> LAN The computer looks for bootable files in the following order: HDD, floppy disk drive*1, CDROM*2 and LAN (Default). HDD −> CD-ROM −> LAN −> FDD The computer looks for bootable files in the following order: HDD, CD-ROM*2, LAN and floppy disk drive*1. FDD −> CD-ROM −> LAN −> HDD The computer looks for bootable files in the following order: floppy disk drive*1, CD-ROM*2, LAN and HDD.
HW Setup 3. Use the left/right cursor keys to highlight the boot device you want and press ENTER. ■ If a supervisor password is set only, it is the following. ■ The menu above appears (able to run HW Setup). ■ The menu above does not appear (unable to run HW Setup). ■ If the supervisor and user password are set, it is the following. ■ The menu above appears when you use the supervisor and user password to start the computer (able to run HW Setup).
HW Setup Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in Standby mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in standby mode. Enabled Enables the Wake-up on Keyboard. Disabled Disables the Wake-up on Keyboard (Default). CPU This function lets you set the CPU operating mode.
HW Setup Built-in LAN This feature enables or disables the Built-in LAN. Enabled Enables Built-in LAN functions (Default). Disabled Disables Built-in LAN functions. Device Config Device Configuration This option lets you set the device configuration. All Devices BIOS sets all devices. Setup by OS Operating system sets devices that it can control (Default). USB USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation.
