User Guide

Battery WiFi Camera
Infrared Light
Light Sensor
Pickup Device
PIR detection
Lens
Indication Light
Speaker
Used for sending system alert tones and the voice intercom
Reset Key
Turn off and turn on the device battery power through the
switch key
The Battery
Switch
Reset Key
Device working status; press and hold for 5 seconds to
restore factory settings
TF Card
Install the TF card to support local video
Bracket
Mounting Hole
Mounting on the wall using accessory brackets
Rear Cover
Screws
Install the battery to power the device by opening the
rear cover
Installation Instructions
Device Connection
① Download " " in the mobile application marketTosee
and open the APP software.(For a better user
experience, please allow all notification permissions
to avoid not getting notifications)
④ On the page, fill in your home WiFi account
Network Configuration
and password, and start the configuration.
⑤ Set the device for sharing and management
administrator password
If you need to reconfigure your WiFi network, press and hold the reset
key for 5 seconds,The red light will flash slowly and you can follow the
instructionsagain to connect
Appearance Introduction
Two 3400mAh original 18650 batteries can be used for
2-3 months
Full HD resolution
Two-way Audio
Support the PIR human body infrared detection, when
someone lingers in the doorway,immediately send alarm
information to the smartphone APP
Day and night mode switches automatically. The clear and
distinct image will help to ensure the safety of you and your
family
Support the 2.4G wireless connection
Support the phone wake-up device
Feature Technical Parameters
Visual Angle Diagonal 104°
Infrared Light 850mm 6pcs
WIFI Support 802.11b/g/n
Audio Two-way intercom with echo cancellation
Video TF card (15 seconds each time)
Storage 8G/16G/32G
Battery 2 pcs of 18650 batteries
Wake-up Method PIR human body induction wake-up
Phone Active Wake-up
Push Speed Push in 2 Seconds
Wake-up Duration Within 600ms
Power Consumption Standby current 300uA
Working current 250mA
It can be used for 2-3 months if working 30 minutes a day with 2
pcs of 18650 batteries (6800mAh).
Installation Instructions
Installation: ① The human body induction effective distance is 3-5
meters, so please adjust the monitoring angle
according to the actual situation.
② Please avoid the installation position where the
temperature changes too much, such as heat
source, airoutlet, etc. which will cause frequent
alarms to the device.
Alarm Adjustment: The device defaults 10 seconds to trigger alarm.
If you need to adjust the sensitivity, please go to
the Device Settings page.
Quick Operation Guide
*Please read the Quick Operation Guide carefully before
using the product and keep it properly.
USB Interface
USB Interface
Charge the device battery through the USB interface
As shown in the figure, remove the screws
and open the back cover
⑥ Device added successfully, please change the name of the device.
Q&A
1. Please confirm that the wireless network to be connected is the
2.4G protocol
2. Make sure that the indication light is in the red light flashing
slowlystate
3. Check if the account password is correct and whether there are
extra spaces
Q: The device cannot connect to WiFi.
A：
Turn on the "Self-Starting" on APP and turn on the notification
function on the "Apply Permissions",Turn off the "Battery
Optimization" and aslo the "End the APP at Background and
Reset Screen"
(Different mobile phone manufacturers have different optimization
methods, please refer to the actual situation)
Q: The device is online and there is a triggering event, but the phone
does not receive push information.
A：
1. The device can work alone with 18650 batteries
2. Possible to charge the device through USB
Q: What power supply methods does the device support?
A：
The device can use the TF card for video storage, or it can use
the real-time recording and capture functions of the mobile phone
for storage
Q: What storage methods does the device support?
NO.006
PIR detection
Lens
Indication Light
Light Sensor
Pickup Device
Infrared Light
Battery Switch
TF Card
Bracket
Mounting Hole
Speaker
Rear Cover
Screws
Push up the snap button upwards to open the
battery compartment and install the battery
+
-
+
-
Pay attention to installation polarity: "+"
positive pole should be installed inwards
(Improper installation can cause damage
to the device)
Name Description
Name Description
Note: You need to open the bottom silicone to see the function interface
as shown in the figure.
Used for collecting the ambient brightness value; when the
illumination is below 2Lux, enable the infrared light
Used for collecting the environment sound and the voice
intercom
When the human body moves in front of the device, it can
generate a trigger signal to the mobile phone
Used for collecting the image video
Red Light Flashing Slowly: System waits for WiFi
configuration
Blue Light Flashing Slowly: System is in normal working
condition
Red and Blue Lights Flashing Alternately: System WiFi
connection failed
When the ambient light is not enough, enable the infrared
light to increase the brightness of the environment
③ Enter the setting page of the mobile phone system according WiFi
tothe prompt. Connect the WIFI sent by the device , return ToSee
to APPand continue to the .next step
② Click the at the top right corner of the APP to add device, select +
Add Device and go to next step.
https://www.camapp365.com/tosee/
battery-wifi-camera