Specification

2
HomewerksWW.com
PRODUCT SPECIFICATIONS
Max. Flow Rate: 1 .2 GPM (4.5 LPM) at 60 PSI Ceramic cartridge
ASME A 11 2. 1 8. 1 /CSA B 1 25
Manufactured to include no more than 0.25% weighted average lead content
on wetted surfaces
NSF 6 1 -9
Polished chrome, brushed nickel or matte black finish
Total weight: 3.42 lbs.
ASSEMBLY INSTRUCTIONS
1 .
Turn off water at the supply valve
under the sink or at the main water
supply. Disconnect the supply lines
and remove the old faucet.
Clean and dry the surface area
where the new faucet will be
mounted.
1
5.
To install the push pop-up drain
assembly (F), turn the drain body
(5.1) in a clockwise direction to
separate it from the flange (5.2).
Remove the mounting nut (5.3),
flat washer (5.4), and rubber cone
washer (5.5) from the flange (5.2).
Leave the rubber gasket (5.6) in
place against the underside of the
push pop-up stopper and trim
ring (5.7).
5.2
5.3
5.4
5.5
5.7
5.6
5.1
Push pop-up drain assembly (F)
5
2. Before installation, unscrew the
mounting nut (C) and remove the
metal washer (D) and the rubber
washer (E).
NOTE: Single hole sinks do not
require the optional deckplate and
gasket (B).
C
D
E
2
6.
From the top of the sink, push the
pre-assembled flange (6.1). with the
rubber gasket (6.2) down through
the drain opening (6.3) in the sink.
6.
6.2
1
6.3
6
3.
Insert the faucet body (A) through
the mounting hole in the sink (3.1).
From underneath the sink, slide
the rubber washer (E) and metal
washer (D) onto the metal shank
(3.2) on the faucet body (A). Secure
the faucet body (A) to the sink by
threading the mounting nut (C)
onto the shank (3.2). Hand tighten
the mounting nut (C) onto the
shank (3.2) until it is securely in
place against the underside of the
sink. DO NOT OVERTIGHTEN.
A
E
C
D
3.2
3.1
3
7.
From underneath the sink, slide
the rubber cone washer onto the
flange (7.1) with the narrow end
up facing the sink drain opening.
Slide on the flat washer. Secure
the flange (7.1) to the sink by
twisting the mounting nut (7.2)
clockwise onto the flange (7.1)
until it is securely in place against
the bottom of the sink. Reas-
semble the push pop-up drain
assembly (F) by turning the drain
body (7.3) clockwise until it is
firmly attached to the bottom of
the flange (7.1). DO NOT
OVERTIGHTEN.
7.1
7.2
7.3
7
4. Optional deckplate installation:
Align the center hole in the
deckplate and gasket (B) with the
center mounting hole (4. 1 ) in the
sink. Insert the faucet body (A)
through the hole in the deckplate
and gasket (B) and the hole in the
sink. From underneath the sink,
slide the rubber washer (E) and
metal washer (D) onto the metal
shank (4.2) on the faucet body (A).
Secure the faucet body (A) to the
sink by threading the mounting
nut (C) onto the shank (4.2). Hand
tighten the mounting nut (C) onto
the shank (4.2) until it is securely in
place against the underside of the
sink. DO NOT OVERTIGHTEN.
A
A
CC
DD
E
4.2
4.1
B
4
8.
To connect the water supply lines,
use 1/2 in. I.P.S. faucet supply lines
(8.1) or coupling nuts (8.2) with
3/8 in. O.D. ball-nose risers (8.3).
These parts are not included.
Attach one end of each of the
water supply lines to the hot and
cold shut-off valves and tighten
with a wrench. Place each of the
remaining ends of the water supply
lines in a bucket. Open both of the
supply valves to turn on the water.
Run the hot and cold water
uninterrupted for about 30
seconds to remove any residue
from the lines. Turn off the water
supply.
8.
8.1
8.2
8.3
8