operation manual

ManualsBrandsTorqeedo ManualsBoats & Boat EnginesElectric outboard motor Travel

100

Table Of Contents

1 Einleitung
- 1.1 Allgemeines zur Anleitung
- 1.2 Zeichenerklärung
- 1.3 Aufbau der Sicherheitshinweise
- 1.4 Zu dieser Betriebsanleitung
- 1.5 Typenschild
2 Geräteregistrierung
3 Ausstattung und Bedienelemente
- 3.1 Lieferumfang
- 3.2 Bedienelemente und Komponenten
4 Technische Daten
- 4.1 Lithium-Ionen-Akku
5 Sicherheit
- 5.1 Sicherheitseinrichtungen
- 5.2 Allgemeine Sicherheitsbestimmungen
6 Inbetriebnahme
- 6.1 Anbau des Antriebs an das Boot
- 6.2 Fixierung der Lenkung
- 6.3 Trimmung des Motors
- 6.4 Akkuversorgung
- 6.5 Inbetriebnahme des Bordcomputers
  - 6.5.1 Anzeigen und Symbole
  - 6.5.2 Anzeige-Einstellungen
7 Betrieb
- 7.1 Not-Stopp
- 7.2 Fahrbetrieb
- 7.3 Kippen des Motors
8 Demontage des Antriebs
9 Trailern/Slippen des Bootes
10 Fehlermeldungen
11 Pflege und Service
- 11.1 Pflege der System-Komponenten
  - 11.1.1 Korrosionsschutz
- 11.2 Service-Intervalle
  - 11.2.1 Ersatzteile
  - 11.2.2 Akkupflege
- 11.3 Wechsel des Propellers
- 11.4 Wechseln der Finne 503 S/L, 1003 S/L und 1003 CS/CL
12 Allgemeine Garantiebedingungen
- 12.1 Gewährleistung und Haftung
- 12.2 Garantieumfang
- 12.3 Garantieprozess
13 Zubehör
14 Entsorgung und Umwelt
- 14.1 Entsorgung von Elektro- und Elektronik-Altgeräten
- 14.2 Entsorgung von Batterien
15 EG-Konformitätserklärung
16 Urheberrecht
1 Introduction
- 1.1 General information on the instructions
- 1.2 Explanation of symbols
- 1.3 Layout of the safety information
- 1.4 About this operating manual
- 1.5 Name plate
2 Registering the device
3 Equipment and controls
- 3.1 Scope of delivery
- 3.2 Controls and components
4 Technical data
- 4.1 Lithium-ion battery
5 Safety
- 5.1 Safety features
- 5.2 General safety provisions
6 Start-up
- 6.1 Installation of the drive to the boat
- 6.2 Fixing the steering in place
- 6.3 Trimming the motor
- 6.4 Battery power
- 6.5 Start-up of the on-board computer
  - 6.5.1 Displays and symbols
  - 6.5.2 Display settings
7 Operation
- 7.1 Emergency Stop
- 7.2 Travel mode
- 7.3 Tilting the motor
8 Disassembling the drive
9 Towing/slipping the boat
10 Error messages
11 Care and service
- 11.1 Care of the system components
  - 11.1.1 Corrosion protection
- 11.2 Maintenance intervals
  - 11.2.1 Replacement parts
  - 11.2.2 Battery maintenance
- 11.3 Replacing the propeller
- 11.4 Replacing the 503 S/L, 1003 S/L and 1003 CS/CL fin
12 General conditions of warranty
- 12.1 Warranty and liability
- 12.2 Scope of warranty
- 12.3 Warranty process
13 Accessories
14 Disposal and environment
- 14.1 Disposal of waste electrical and electronic equipment
- 14.2 Disposal of batteries
15 EC Declaration of Conformity
16 Copyright

Error messages

DE EN

Display Cause What to do

E21 Incorrect calibration of tiller Recalibrate:

1. Press and hold the CAL button for ten seconds.

cal up appears on the display.

2. Set the tiller to full throttle forwards.

3. Press the CAL button.

cal stp appears on the display.

4. Set the tiller to the neutral position.

5. Press the CAL button.

cal dn appears on the display.

6. Set the tiller to full throttle reverse.

7. Press the CAL button.

E22 Magnetic sensor defective

Recalibrate, see "E21". If the error code appears several times, then con-

tact Torqeedo Service.

E23 Value range incorrect

Recalibrate, see "E21".

E30 Communication error with motor Check the cables and the plug connections of the data cables.

Clean the contacts using contact spray.

If necessary, contact Torqeedo Service and tell them the error code.

E32 Tiller communication error Check the plug connections on the tiller.

Clean the contacts using contact spray.

Check the cable.

page 94 / 112