operation manual

ManualsBrandsTorqeedo ManualsBoats & Boat EnginesElectric outboard motor Travel

Table Of Contents

1 Einleitung
- 1.1 Allgemeines zur Anleitung
- 1.2 Zeichenerklärung
- 1.3 Aufbau der Sicherheitshinweise
- 1.4 Zu dieser Betriebsanleitung
- 1.5 Typenschild
2 Geräteregistrierung
3 Ausstattung und Bedienelemente
- 3.1 Lieferumfang
- 3.2 Bedienelemente und Komponenten
4 Technische Daten
- 4.1 Lithium-Ionen-Akku
5 Sicherheit
- 5.1 Sicherheitseinrichtungen
- 5.2 Allgemeine Sicherheitsbestimmungen
6 Inbetriebnahme
- 6.1 Anbau des Antriebs an das Boot
- 6.2 Fixierung der Lenkung
- 6.3 Trimmung des Motors
- 6.4 Akkuversorgung
- 6.5 Inbetriebnahme des Bordcomputers
  - 6.5.1 Anzeigen und Symbole
  - 6.5.2 Anzeige-Einstellungen
7 Betrieb
- 7.1 Not-Stopp
- 7.2 Fahrbetrieb
- 7.3 Kippen des Motors
8 Demontage des Antriebs
9 Trailern/Slippen des Bootes
10 Fehlermeldungen
11 Pflege und Service
- 11.1 Pflege der System-Komponenten
  - 11.1.1 Korrosionsschutz
- 11.2 Service-Intervalle
  - 11.2.1 Ersatzteile
  - 11.2.2 Akkupflege
- 11.3 Wechsel des Propellers
- 11.4 Wechseln der Finne 503 S/L, 1003 S/L und 1003 CS/CL
12 Allgemeine Garantiebedingungen
- 12.1 Gewährleistung und Haftung
- 12.2 Garantieumfang
- 12.3 Garantieprozess
13 Zubehör
14 Entsorgung und Umwelt
- 14.1 Entsorgung von Elektro- und Elektronik-Altgeräten
- 14.2 Entsorgung von Batterien
15 EG-Konformitätserklärung
16 Urheberrecht
1 Introduction
- 1.1 General information on the instructions
- 1.2 Explanation of symbols
- 1.3 Layout of the safety information
- 1.4 About this operating manual
- 1.5 Name plate
2 Registering the device
3 Equipment and controls
- 3.1 Scope of delivery
- 3.2 Controls and components
4 Technical data
- 4.1 Lithium-ion battery
5 Safety
- 5.1 Safety features
- 5.2 General safety provisions
6 Start-up
- 6.1 Installation of the drive to the boat
- 6.2 Fixing the steering in place
- 6.3 Trimming the motor
- 6.4 Battery power
- 6.5 Start-up of the on-board computer
  - 6.5.1 Displays and symbols
  - 6.5.2 Display settings
7 Operation
- 7.1 Emergency Stop
- 7.2 Travel mode
- 7.3 Tilting the motor
8 Disassembling the drive
9 Towing/slipping the boat
10 Error messages
11 Care and service
- 11.1 Care of the system components
  - 11.1.1 Corrosion protection
- 11.2 Maintenance intervals
  - 11.2.1 Replacement parts
  - 11.2.2 Battery maintenance
- 11.3 Replacing the propeller
- 11.4 Replacing the 503 S/L, 1003 S/L and 1003 CS/CL fin
12 General conditions of warranty
- 12.1 Warranty and liability
- 12.2 Scope of warranty
- 12.3 Warranty process
13 Accessories
14 Disposal and environment
- 14.1 Disposal of waste electrical and electronic equipment
- 14.2 Disposal of batteries
15 EC Declaration of Conformity
16 Copyright

Start-up

DE EN

6.5.2 Display settings

Fig. 53: Multifunction display - Set-up menu

In the Set-up menu, you can select the units to be displayed on screen (in orange).

1. Press the Set-up button in order to access the Set-up menu.

2. Use the CAL button to set the unit in which the remaining range is to be dis-

played.

You can select between kilometres, American miles, nautical miles,

and hours.

3. Confirm your selection using the Set-up button.

The setting for the speed display is shown.

4. Use the CAL button to set the unit in which the speed is to be displayed.

You can select between kilometres per hour, miles per hour, and knots.

5. Confirm your selection using the Set-up button.

The setting for the battery status display is shown.

6. Use the CAL button to set the unit in which the battery status is to be displayed.

You can select between Volts and percent.

7. Confirm your selection using the Set-up button.

page 82 / 112