Form No. 3447-163 Rev A Pole Hedge Trimmer Attachment Flex-Force Power System™ 60V MAX String Trimmer Model No. 88713—Serial No. 321000001 and Up Register at www.Toro.com.
Important: With your mobile device, you can scan the QR code (if equipped) on the serial number plate to access warranty, parts, and other product information. For assistance, please see www.Toro.com/support for instructional videos or contact your Authorized Service Dealer before returning this product. Introduction This pole hedge trimmer attachment is intended to be used by residential homeowners to maintain bushes and hedges. It is to be used only by adults.
Safety Use of a cord suitable for outdoor use reduces the risk of electric shock. 6. WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. III. Personal safety Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. 1. Stay alert, watch what you are doing and use common sense when operating a power tool.
V. Battery tool use and care IV. Power tool use and care 1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 1. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 2. Do not use the power tool if the switch does not turn it on and off.
2. VII. Hedge trimmer safety warnings Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers. 1. To reduce the risk of electrocution, never use the extended-reach hedge trimmer near any electrical power lines. Contact with or use near power lines may cause serious injury or electric shock resulting in death. 2. Always use two hands when operating the extended-reach hedge trimmer.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal145-3134 145-3134 decal145-3136 145-3136 1.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Connect the attachment to the power head. No parts required – Install the harness. Connecting the Attachment to the Power Head 1. Install the square shaft of the attachment into the square shaft of the power head (A of Figure 3). 2. Align the locking button on the lower shaft with the slotted hole on the upper shaft and slide the 2 shafts together (B and C of Figure 3). 3.
Installing the Harness Connect the metal hook on the shoulder harness to the strap collar on the pole saw handle (Figure 4). g364485 Figure 4 1. Strap adjuster 3. Strap collar 2. Metal strap hook 4. Shoulder strap The strap length is adjustable; slide the strap adjuster up to decrease the length of the strap, or down to increase the length of the strap (Figure 4). If there is ever an emergency and you need to rapidly remove the harness, disconnect the quick-release buckle as follows: 1.
Specifications Product Overview Model 88713, attaches to 51832/51832T Cutting Length 406 mm (16 inches) Rated Voltage 60V DC maximum, 54 VDC nominal usage No-load Speed 3000 spm at 60 VDC max Cutting width 23 mm (9/10 inch) Weight (attached to powerhead without a battery) 4.8 kg (10.6 lbs) Charger Type 88610 (included with 51832), 88602, or 88605 Battery Type 88620 (included with 51832), 88625, 88640, 88650, 88660, or 88675* Appropriate Temperature Ranges g358713 Figure 6 1. Blades 4.
Rotating the Hedge Trimmer Head Operation Starting the Attachment 1. 2. The hedge trimmer head can rotate 90° for different cutting situations. Ensure that the vents on the attachment, power head, and battery are clear of any dust and debris. Align the cavity in the battery pack with the tongue on the handle housing (Figure 7). 1. Remove the battery pack; refer to Removing the Battery Pack from the Power Head (page 11). 2.
Operating Tips Shutting Off the Hedge Trimmer • Use the power tool for cutting in either direction in a slow, sweeping action from side to side. To shut off the hedge trimmer, release the run trigger (Figure 8). Allow at least 5 seconds for the cutting blade to stop moving. • When trimming new growth, use a wide sweeping action so that the stems are fed directly into the cutting blade.
Maintenance Storage Remove the battery pack before maintenance or cleaning work. Important: Store the tool, battery pack, and charger only in temperatures that are within the appropriate range; refer to Specifications (page 9). Use only the manufacturer’s recommended replacement parts and accessories. Important: If you are storing the battery pack for the off-season, charge it until 2 or 3 LED indicators turn green on the battery. Do not store a fully charged or fully depleted battery.
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem The tool does not start. Possible Cause Corrective Action 1. The battery is not fully installed in the tool. 1. Remove and then replace the battery into the tool, making sure that it is fully installed and latched. 2.
Notes:
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
