Form No. 3323–292 Compact Series Z150 with 44I SFS Side Discharge Mower Model No.
Introduction Thank you for purchasing a Toro product. All of us at Toro want you to be completely satisfied with your new product, so feel free to contact your local Authorized Service Dealer for help with service, genuine replacement parts, or other information you may require. Whenever you contact your Authorized Service Dealer or the factory, always know the model and serial numbers of your product.
Contents Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safe Operating Practices . . . . . . . . . . . . . . Toro Mower Safety . . . . . . . . . . . . . . . . . . Slope Chart . . . . . . . . . . . . . . . . . . . . . . . . . Safety and Instruction Decals . . . . . . . . . . Gasoline and Oil . . . . . . . . . . . . . . . . . . . . . . . . Recommended Gasoline . . . . . . . . . . . . . . Using Stabilizer/Conditioner . . . . . . . . . . . Filling the Fuel Tank . . . . . . . . . . . .
Contents Mercury Tilt Switch . . . . . . . . . . . . . . . . . . Mercury Tilt Switch Disposal . . . . . . . . . . Wiring Diagram . . . . . . . . . . . . . . . . . . . . . 59 59 60 Cleaning and Storage . . . . . . . . . . . . . . . . . 61 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 62 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety This machine meets or exceeds CPSC blade safety requirements for rotary mowers and the B71.4 1999 specifications of the American National Standards Institute, in effect at time of production. Note: The addition of certain attachments that do not meet American National Standards Institute certification will cause noncertification of this machine. Improper use or maintenance by the operator or owner can result in injury.
Safety Operation • Never run an engine in an enclosed area. • Only operate in good light, keeping away from holes and hidden hazards. • Be sure all drives are in neutral and parking brake is engaged before starting engine. Only start engine from the operator’s position. Use seat belts if provided. • Slow down and use extra care on hillsides. Be sure to travel in the recommended direction on hillsides. Turf conditions can affect the machine’s stability. Use caution while operating near drop–offs.
Safety • Use care when checking blades. Wrap the blade(s) or wear gloves, and use caution when servicing them. Only replace blades. Never straighten or weld them. • Keep hands and feet away from moving parts. If possible, do not make adjustments with the engine running. • Charge batteries in an open well ventilated area, away from spark and flames. Unplug charger before connecting or disconnecting from battery. Wear protective clothing and use insulated tools.
Safety • Before operating a machine with ROPS (roll over protection) be certain the seat belts are attached to prevent the seat from pivoting forward. Slope Operation • When operating a machine with ROPS (roll over protection) always use seat belt. • Be certain that the seat belt can be released quickly if the machine is driven or rolls into ponds or water. • Check carefully for overhead clearances (i.e. branches, doorways, electrical wires) before driving under any objects and do not contact them.
Safety • Check brake operation frequently. Adjust and service as required. • Battery acid is poisonous and can cause burns. Avoid contact with skin, eyes and clothing. Protect your face, eyes and clothing when working with a battery. • Battery gases can explode. Keep cigarettes, sparks and flames away from battery. • Hydraulic fluid escaping under pressure can penetrate the skin and cause injury. Use cardboard or paper to find hydraulic leaks.
Safety 8
Safety Slope Chart Read all safety instructions on pages 5–7.
10
Safety Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. TOP OF CONSOLE UNDER SEAT (Part No. E513747) ON RIGHT SIDE OF HEIGHT OF CUT PLATE (Part No E653140) BELOW CENTER OF CONSOLE (Part No. E633346) ON FRAME UNDER SEAT (Part No. E603845) ON LEFT SIDE OF HEIGHT–OF–CUT PLATE (Part No E653147) ON TOP OF HYDRAULIC RESERVOIR (Part No.
Safety UNDER FOOTREST (Part No. 99–3924) ON FRAME NEAR MUFFLER (Part No. 65–2690) LOWER LEFT OF CONSOLE (Part No. 98–4387) ON TOP LEFT SIDE OF FRAME (Part No. E633818) YEA RLY ON CONTROL PANEL (Part No.
Safety ON RIGHT SIDE OF MOWER (Part No. 66-1340) UNDER DEFLECTOR (Part No. 66-6380) ON DEFLECTOR (Part No. 54-9220) ON LEFT SIDE OF MOWER (Part No. 43-8480) UNDER BELT COVER (3) UNDER FOOT REST (1) (Part No. 98Ć5954) (2) ON BELT COVERS (Part No. 67-5360) ON TOP OF MOWER IN CENTER (Part No. 98-3798) ON TOP CENTER OF MOWER (Part No. 99-3943) ON LEFT FRONT OF MOWER (Part No.
Gasoline and Oil Recommended Gasoline Use UNLEADED Regular Gasoline suitable for automotive use (85 pump octane minimum). Leaded regular gasoline may be used if unleaded regular is not available. IMPORTANT: Never use methanol, gasoline containing methanol, or gasohol containing more than 10% ethanol because the fuel system could be damaged. Do not mix oil with gasoline. POTENTIAL HAZARD • In certain conditions gasoline is extremely flammable and highly explosive.
Gasoline and Oil Filling the Fuel Tank POTENTIAL HAZARD • Gasoline is harmful or fatal if swallowed. Long–term eposure to vapors has caused cancer to laboratory animals. 1. Shut the engine off and set the parking brake. 2. Clean around each fuel tank cap and remove the cap. Add unleaded regular gasoline to both fuel tanks, until the level is 1/4 to 1/2 inch (6 mm to 13 mm) below the bottom of the filler neck. This space in the tank allows gasoline to expand. Do not fill the fuel tanks completely full.
Assembly Loose Parts Note: Use the chart below to verify all parts have been shipped. DESCRIPTION QTY.
Assembly Install Drive Wheels Install Seat Retaining Rod 1. Uncrate mower. 4. 1. Remove wheel bolts or nuts from rear wheel hubs. Tilt seat up. Remove 5/16” (8mm) locknut from bolt attaching seat retaining rod to seat frame (Fig. 2). 5. 2. Align holes. Mount drive wheels with the valve stem to the outside of the traction unit. 3. Secure using wheel bolts or nuts provided. Torque to 95ft–lbs (128 NSM).
Assembly Install Motion Control Levers 1. Remove the (4) 3/8–16 x 1” (26 mm) bolts and (4) 3/8” spring washers which attach the motion control levers to the control arm shafts for shipping (Fig. 3). 2. Place the levers (with the mounting plate towards the rear) on the outside of the control arm shaft and secure with (4) 3/8–16 x 1” (26 mm) bolts and (4) 3/8” spring washers (Fig. 3). 3. Position the lever so the bolts are in the center of the slots on the lever mounting plate and tighten until snug.
Assembly Activate the Battery 3. Bulk electrolyte with 1.260 specific gravity must be purchased from a local battery supply outlet. Remove filler caps from the battery. Slowly pour electrolyte into each cell until the electrolyte level is up to the lower part of the tube (Fig. 5). 1 1. Remove the battery from the machine. IMPORTANT: Be careful not to damage the long vent tube when removing the battery box.
Assembly Install Battery 1. Position battery in tray with terminal posts toward the engine (Fig. 7). WHAT CAN HAPPEN • Battery gasses can explode. 2. First, install the positive (red) battery cable to positive (+) battery terminal. HOW TO AVOID THE HAZARD • Keep cigarettes, sparks and flames away from battery. 3. Then install negative battery cable and ground wire to the negative (–) battery terminal. 4. Secure cables with (2) 1/4 x 3/4” (19 mm) bolts 1/4” washers and 1/4” locknuts (Fig. 7). 5.
Assembly Hydraulic System 1 Checking the Hydraulic Fluid Check the hydraulic fluid level before engine is first started. 2 3 Fluid Type: Mobil 1 15W–50 synthetic motor oil. IMPORTANT: Use only oil specified. Other fluids could cause system damage. Figure 8 Hydraulic System Oil Capacity: 2.1 qt. (2.0 l) 1. Cap 2. Baffle 3. Fluid level-Full 1. Position machine on a level surface and set the parking brake. 2. Clean area around filler neck of hydraulic tank (Fig. NO TAG). 3.
Assembly Greasing the Bearings Check Engine Oil Level Make sure cutting unit spindles are full of grease before engine is first started. Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking Oil Level, page 42. Grease with No. 2 general purpose lithium base or molybdenum base grease. 1. Grease the fittings on the three spindle bearings. Grease until it comes out lower seals (Fig. 9). 1 M-4269 Figure 9 1.
Operation Think Safety First Controls Please carefully read all the safety instructions on pages 3–13. Knowing this information could help you, your family, pets or bystanders avoid injury. Become familiar with all the controls (Fig. 1) before you start the engine and operate the machine. 1 8 8 2 2 POTENTIAL HAZARD • Loud sound can cause ear damage and loss of hearing. WHAT CAN HAPPEN • Ear damge or hearing loss may occur. HOW TO AVOID THE HAZARD • Wear ear protection when operating this machine.
Operation Parking Brake Always set the parking brake when you stop the machine or leave it unattended. Releasing the Parking Brake 1. Push forward and down on the parking brake lever to release the parking brake (Fig. 2). The parking brake is “DISENGAGED”. IMPORTANT: Do not park on slopes unless wheels are chocked or blocked. 1 Setting the Parking Brake 1. 2. Move the motion control levers (Fig. 1) out to the neutral lock position.
Operation Starting and Stopping the Engine 2 1 Starting 2 1. Sit down on the seat and move the motion controls to neutral locked position. 2. Set the parking brake; refer to Setting the Parking Brake, page 24. 3. Move the PTO (power take off) to “OFF” (Fig. 4). 4. Move the choke control to “ON” position before starting a cold engine (Fig. 5). Note: 5. 6. m–4201 Figure 4 m–2719 Figure 5 1. PTO-On 2. PTO-Off A warm or hot engine may require choking.
Operation 1. Move the throttle lever to “SLOW” (Fig. 6). Operating the Power Take Off (PTO) 2. Move the PTO (power take off) to “OFF” (Fig. 4). The power take off (PTO) switch engages and disengages power to the electric clutch. 3. Turn the ignition key to “OFF” (Fig. 7). Stopping Note: If the engine has been working hard or is hot, let it idle for a minute before turning the ignition key “OFF.” This helps cool the engine before it is stopped.
Operation The Safety Interlock System Understanding the Safety Interlock System The safety interlock system is designed to prevent the engine from starting unless: • You are sitting on the seat • The parking brake is on “ENGAGED” • The power take off (PTO) is disengaged “OFF” • The motion control levers are in neutral lock position The safety interlock system also is designed to stop the engine when the traction controls are moved with the parking brake on “ENGAGED” or if you rise from the seat whe
Operation Driving Forward or Backward The throttle control regulates the engine speed as measured in rpm (revolutions per minute). Place the throttle control in the “FAST” position for best performance. Always operate in the full throttle position The farther you move the traction control levers in either direction, the faster the machine will move in that direction. To stop pull the motion control levers to neutral.
Operation Fuel Tanks POTENTIAL HAZARD • Someone could move or attempt to operate the tractor while it is unattended. WHAT CAN HAPPEN • Children or bystanders may be injured if they use the tractor. HOW TO AVOID THE HAZARD • Always remove the ignition key and set the parking brake when leaving the machine, even if just for a few minutes. The unit has two fuel tanks, one located on the left and on the right side. Each tank connects to the fuel shut off valve in the control panel.
Operation Adjusting Height-of-Cut Adjusting Anti-Scalp Rollers The height-of-cut is adjusted from 1-1/2” to 4-1/2” (38 to 114 mm) in 1/4” (6 mm) increments by relocating clevis pin in different hole locations. Whenever you change the height-of-cut it is recommended to adjust the height of the anti-scalp rollers. 1. Raise the height-of-cut lever to the transport position (also the 4-1/2” (114 mm) cutting height position) (Fig. 12). 2.
Operation Positioning the Seat Center Rollers 1. Disengage the power take off (PTO) and turn the ignition key to “OFF”. Move controllers to neutral locked position and apply parking brake. 1. After adjusting height-of-cut, remove bolt and nut (Fig. 14). 2. Select hole so gage wheel is positioned to the nearest corresponding height-of-cut desired (Fig. 14). Note: 3. The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable. 1.
Operation Pushing the Machine by Hand Side Discharge IMPORTANT: Always push the machine by hand. Never tow the machine because hydraulic damage may occur. The mower has a hinged grass deflector that disperses clippings to the side and down toward the turf. To Push the Machine 1. Disengage the power take off (PTO) and turn the ignition key to “OFF” to stop the engine. 2. Rotate the by-pass valves counterclockwise 1 turn to push.
Operation Transporting Machines Loading Machines Use a heavy–duty trailer or truck to transport the machine. Ensure that the trailer or truck has all necessary lighting and marking as required by law. Please carefully read all the safety instructions on pages 3–13. Knowing this information could help you, your family, pets or bystanders avoid injury. Use extreme caution when loading units on trailers or trucks.
Operation POTENTIAL HAZARD • Loading a unit on a trailer or truck increases the possibility of backward tip–over. WHAT CAN HAPPEN • Backward tip–over of the unit could cause serious injury or death. HOW TO AVOID THE HAZARD • Use extreme caution when operating a unit on a ramp. • Use only a single, full width ramp; DO NOT use individual ramps for each side of the unit. • If individual ramps must be used, use enough ramps to create an unbroken ramp surface wider than the unit.
Operation Tips for Mowing Grass Fast Throttle Setting Cutting Speed To improve cut quality, use a slower ground speed. For best mowing and maximum air circulation, operate the engine at “FAST.” Air is required to thoroughly cut grass clippings, so do not set the height-of-cut so low as to totally surround the mower by uncut grass. Always try to have one side of the mower free from uncut grass, which allows air to be drawn into the mower.
Maintenance Service Interval Chart Service Operation Each Use 8 Hours 25 Hours Hydraulic fluid–check level Initial Initial X Oil—check level 50 Hours 100 Hours X Initial X Oil Filter–change (200 hours or every other oil change) Hydraulic filter–change Storage Service X X Oil—change* Safety System—check 200 Hours Initial X X X X X X X Chassis—grease* X X Linkage bushings—oil* X X Foam Air Cleaner—service* X X Paper Air Cleaner—service* X X Paper Air Cleaner—replace* X
Maintenance POTENTIAL HAZARD • If you leave the key in the ignition switch, someone could start the engine. WHAT CAN HAPPEN • Accidental starting of the engine could seriously injure you or other bystanders. HOW TO AVOID THE HAZARD • Remove the key from the ignition switch and pull the wire(s) off the spark plug(s) before you do any maintenance. Also push the wire(s) aside so it does not accidentally contact the spark plug(s).
Maintenance Inspecting the Blades Checking for Bent Blades 1. 1. Stop the engine, set the parking brake, remove the key and disconnect the spark plug wire(s) from the spark plug(s). 2. Rotate the blades until the ends face forward and backward (Fig. 18). Measure from a level surface to the cutting edge of the blades (Fig. 19). Note this dimension. 2. Inspect the cutting edges (Fig 17). If the edges are not sharp or have nicks, remove and sharpen the blades.
Maintenance Sharpening the Blades 1. POTENTIAL HAZARD • A blade that is bent or damaged could break apart and pieces could be thrown at bystanders or at you as you use the mower. Use a file to sharpen the cutting edge at both ends of the blade (Fig. 21). Maintain the original angle. The blade retains its balance if the same amount of material is removed from both cutting edges. WHAT CAN HAPPEN • Pieces of blade that may be thrown could seriously injure or kill you or bystanders.
Maintenance Air Cleaner 3. Carefully slide the foam element off the paper element (Fig. 23). Foam Element: Clean and re-oil after every 25 operating hours. 4. Unscrew the cover nut and remove the cover and paper element (Fig. 23). Paper Element: Replace after every 100 operating hours. Note: Cleaning the Foam and Paper Elements Service the air cleaner more frequently (every few hours) if operating conditions are extremely dusty or sandy. Removing the Foam and Paper Elements 1. 2. 1.
Maintenance 2. Paper Element Engine Oil A. Lightly tap the element on a flat surface to remove dust and dirt (Fig. 25). Change oil: B. Inspect the element for tears, an oily film, and damage to the rubber seal. IMPORTANT: Never clean the paper element with pressurized air or liquids, such as solvent, gas, or kerosene. Replace the paper element if it is damaged or cannot be cleaned thoroughly. • After the first 5 operating hours. • After every 100 operating hours.
Maintenance Checking Oil Level Changing/Draining Oil 1. 1. Start the engine and let it run five minutes. This warms the oil so it drains better. 2. Park the machine so that the drain side is slightly lower than the opposite side to assure the oil drains completely. Then disengage the power take off (PTO), set the parking brake, and turn the ignition key to “OFF” to stop the engine. Remove the key. 3. Place a pan below the oil drain. Remove the oil drain cap (Fig. 27). 4.
Maintenance Spark Plug Change Oil Filter Replace the oil filter every 200 hours or every other oil change. Note: 1. Change oil filter more frequently when operating conditions are extremely dusty or sandy. Drain the oil from the engine; refer to Changing/Draining Oil, page 42. 2. Remove the old filter and wipe the filter adapter (Fig. 28) gasket surface. 3. Pour new oil of the proper type in through the center hole. Stop pouring when the oil reaches the bottom of the threads.
Maintenance Fuel Filter Checking the Spark Plug 1. Look at the center of the spark plug(s) (Fig. 30). If you see light brown or gray on the insulator, the engine is operating properly. A black coating on the insulator usually means the air cleaner is dirty. IMPORTANT: Never clean the spark plug(s). Always replace the spark plug(s) when it has a black coating, worn electrodes, an oily film, or cracks. 2. Check the gap between the center and side electrodes (Fig. 30). Bend the side electrode (Fig.
Maintenance Fuel Tank Draining The Fuel Tank 4. Pull the fuel line off fuel filter (Fig. 32). 5. Open fuel shut-off valve for left and right tanks. Allow gasoline to drain into a gas can or drain pan. (Fig. 32). Note: POTENTIAL HAZARD • In certain conditions gasoline is extremely flammable and highly explosive. 6. Now is the best time to install a new fuel filter because the fuel tank is empty. Install the fuel line onto the fuel filter.
Maintenance Greasing and Lubrication Lubricate the machine when shown on the CHECK SERVICE REFERENCE AID decal (Fig. 33). Grease more frequently when operating conditions are extremely dusty or sandy. Grease with No. 2 general purpose lithium base or molybdenum base grease. How to Grease 1. Disengage the power take off (PTO) and turn the ignition key to “OFF” to stop the engine. Remove the key. 2. Clean the grease fittings with a rag. Make sure to scrape any paint off the front of the fitting(s). 3.
Maintenance Greasing the Bearings Hydraulic System The cutting unit must be lubricated regularly. Refer to the Service Interval Chart on page 36. Grease with No. 2 general purpose lithium base or molybdenum base grease. Checking the Hydraulic Fluid • Before engine is first started. 1. Stop the engine, set the parking brake, remove the key and disconnect the spark plug wire(s) from the spark plug(s). • After first 8 operating hours. • After 25 operating hours. 2.
Maintenance Replacing the Hydraulic Filter 1 Change the hydraulic filter: 2 3 • After the first 8 operating hours. • After every 200 operating hours. 1. Position machine on a level surface, stop the engine, and remove key from ignition switch. IMPORTANT: Do not substitute automotive oil filter or severe hydraulic system damage may result. Figure 35 1. Cap 2. Baffle 3. Fluid level-Full 2.
Maintenance Check Hydraulic Lines 1 After every 100 operating hours, check hydraulic lines and hoses for leaks, loose fittings, kinked lines, loose mounting supports, wear, weather and chemical deterioration. Make necessary repairs before operating. 3 2 m–1256 Figure 37 1. Hydraulic filter 2. Gasket 3. Adapter 7. Clean up any spilled fluid. 8. Start engine and let run for about two minutes to purge air from the system. Stop the engine and check for leaks.
Maintenance Wheel Hub Slotted Nut 1 Check after every 500 operating hours. The slotted nut needs to be torqued to 125 ft–lbs (169.5 NSm). m–1872 1. Stop the engine, set the parking brake, remove the key and disconnect the spark plug wire(s) from the spark plug(s). 2. Remove cotter pin. 3. Torque slotted nut to 125 ft–lbs (169.5 NSm) (Fig. 40). 4. Check the distance from bottom of slot in nut to inside edge of hole. Two threads or less should be showing (Fig. 40). 5.
Maintenance Mower Leveling Note: 1. Position mower on a flat surface. Stop the engine, set the parking brake, remove the key and disconnect the spark plug wire(s) from the spark plug(s). 2. Check tire pressure of all four (4) tires. If needed, adjust to 13 psi (90 kPa) 3. Set anti–scalp rollers to top holes or remove them completely for this adjustment. 8. When hardware is loose, deck will rotate the lift handle up out of position.
Maintenance 12. Raise deck to 3 inch height of cut and measure actual height from blade tips to ground. Height of cut for the front blade tips should be 3.00 ±.125 (76mm ± 3mm). Height of cut for rear blade tips should be 3.25±.125 (83mm± 3mm).Readjust if needed. Note: When checking blade tip heights make sure blades are not bent and check blade pointing front to rear. 13. Install anti–scalp rollers for proper height-of-cut and tighten securely. See Adjusting Anti Scalp Rollers on page 30.
Maintenance Throttle Lever Adjustment Clean Under Deck The tension can be adjusted by adjusting the tightness of lever pivot bolt. Do this when needed. Remove grass build up under deck daily. 1. Stop engine, remove ignition key. 2. Remove console from machine to gain access to throttle lever. 3. Tighten nut and bolt. Test lever to your desired tension (Fig. 44). 1 3 4 2 5 6 1. Position mower on a flat surface.
Maintenance Replacing the Deck Belt Squealing when the belt is rotating, blades slipping when cutting grass, frayed belt edges, burn marks and cracks are signs of a worn deck belt. Replace the deck belt if any of these conditions are evident. 1. POTENTIAL HAZARD • Spring is under tension when installed. WHAT CAN HAPPEN • Stored spring energy can cause personal injury. Stop the engine, set the parking brake, remove the key and disconnect the spark plug wire(s) from the spark plug(s). 2.
Maintenance Replacing the Pump Drive Belt Replacing the Grass Deflector Check pump drive belt for wear after every 50 hours of operation. 1. Stop the engine, set the parking brake, remove the key and disconnect the spark plug wire(s) from the spark plug(s). 2. Remove the locknuts, bolts and springs holding the deflector mounts to the pivot brackets (Fig. 48). 3.
Maintenance Adjusting Motion Controls 5. Apply slight rearward pressure on the motion control lever, turn the head of the adjustment bolt in the appropriate direction until lever is centered in neutral lock position (keeping rearward pressure on the lever will keep the pin at the end of the slot and allow the adjustment bolt to move the lever to the appropriate position (Fig. 50). 6. Tighten nut and jam nut. 7. Repeat on opposite side of unit.
Maintenance Adjusting Hydraulic Pump Neutral Note: 1. Note: Motion control lever must be in neutral while making any adjustments. Adjust handle neutral first. That has to be correct before the following adjustment can be made. 8. Open throttle to fast. Make sure wheel remains stopped or slightly creeps in reverse, re-adjust if necessary. This adjustment must be made with drive wheels turning. First raise the frame and block up so drive wheels can rotate freely. 9. Repeat on opposite side of unit.
Maintenance Adjustment Parking Brake Fuse Check parking brake for proper adjustment. Service Interval/Specification 1. Disengage brake lever (lever down). 2. Measure the length of the spring. Measurement should be 2.75” (74 mm) between washers (Fig. 51). The electrical system is protected by fuses. It requires no maintenance: however, if a fuse blows check component/circuit for malfunction or short. 3.
Maintenance Battery Adding Water to the Battery Check the electrolyte level in the battery every 25 hours. Always keep the battery clean and fully charged. Use a paper towel to clean the battery case. If the battery terminals are corroded, clean them with a solution of four parts water and one part baking soda. Apply a light coating of grease to the battery terminals to prevent corrosion. The best time to add distilled water to the battery is just before you operate the machine.
Maintenance Waste Disposal Mercury Tilt Switch Disposal Engine oil, hydraulic oil and engine coolant are pollutants to the environment. Dispose of these according to your state and local regulations. Several states have passed laws concerning the disposal of devices containing mercury. In all the remaining states it is advisable to follow similar procedures.
Maintenance Wiring Diagram 61
Maintenance Cleaning and Storage 1. 2. Disengage the power take off (PTO), set the parking brake and turn the ignition key to “OFF” to stop the engine. Remove the key. Remove grass clippings, dirt, and grime from the external parts of the entire machine, especially the engine. Clean dirt and chaff from the outside of the engine’s cylinder head fins and blower housing. IMPORTANT: You can wash the machine with mild detergent and water. Do not pressure wash the machine.
Troubleshooting PROBLEM Starter does not crank Engine will not start, starts hard, or fails to keep running. Engine g loses power. POSSIBLE CAUSES CORRECTIVE ACTION 1. Blade control (PTO) is ENGAGED. 1. Move blade control (PTO) to DISENGAGED. 2. Parking brake is not on. 2. Set parking brake. 3. Operator is not seated. 3. Sit on the seat. 4. Battery is dead. 4. Charge the battery. 5. Electrical connections are corroded or loose. 5. Check electrical connections for good contact. 6.
Troubleshooting PROBLEM Engine g overheats. Abnormal vibration. Machine does not drive. Abnormal vibration. 64 POSSIBLE CAUSES CORRECTIVE ACTION 1. Engine load is excessive. 1. Reduce ground speed. 2. Oil level in crankcase is low. 2. Add oil to crankcase. 3. Cooling fins and air passages under engine blower housing are plugged. 3. Remove obstruction from cooling fins and air passages. 1. Engine mounting bolts are loose. 1. Tighten engine mounting bolts. 2.
Troubleshooting PROBLEM Uneven cutting g height. g Blades do not rotate. POSSIBLE CAUSES CORRECTIVE ACTION 1. Blade(s) not sharp. 1. Sharpen blade(s). 2. Cutting blade(s) is/are bent. 2. Install new cutting blade(s). 3. Mower is not level. 3. Level mower from side-to-side and front-to-rear. 4. Gage wheel not set correctly. 4. Adjust gage wheel height. 5. Underside of mower is dirty. 5. Clean the underside of the mower. 6. Tire pressure is incorrect. 6. Adjust tire pressure. 7.
A OneĆYear Limited Warranty (A TwoĆYear Full Warranty for Residential Use) LCE What Is Covered By This Express Warranty? The Toro Company promises to repair any TORO Product used for commercial, institutional, or rental purposes if defective in materials or workmanship. The following time frames apply from the date of purchase: Product Warranty Period All Products . . . . . . . . . . . . . . . . . . 1 year All Spindles . . . . . . . . . . . . . . . . . . .
