Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 74141TE

FormNo.3372-979RevA

ZMaster

RidingMower

with48inTURBOFORCE

SideDischargeMower

ModelNo.74141TE—SerialNo.312000001andUp

SetupInstructions

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Removepartsfromthecrate.

Nopartsrequired

–

Checkthetirepressure.

Rearwheels2Installtherearwheels.

RolloverProtectionSystemKit(ROPS)

InstalltheRolloverProtectionSystem

(ROPS).

Seat

Seatplate

Guard

Flangenuts(5/16inch)

Installtheseat.

Nopartsrequired

–

Checktheseatbelt.

Rightcontrollever1

Leftcontrollever

Bolt(3/8x1inch)(2areassembled)

Nut(3/8inch)(2areassembled)

Installthemotioncontrollevers.

Carriagebolt(3/8x1-1/2inches)

Flangenut(3/8inch)

Installtheliftassistpedal.

Aircleanercap1

Hoseclamp1

Installtheaircleanercap.

Nopartsrequired

–

Chargeandinstallthebattery.

Nopartsrequired

–

Checktheengineoillevel.

Nopartsrequired

–

Addfueltothemachine.

Number2generalpurposelithiumbase

ormolybdenumbasegrease.(Purchase

separately.)

1tube

Checkthemachineforgrease.

Nopartsrequired

–

Preparethesidedischargechute.

Nopartsrequired

–

Testthesafetyinterlocksystem.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (12 pages)

PAGE 1
Form No. 3372-979 Rev A Z Master® Riding Mower with 48in TURBO FORCE® Side Discharge Mower Model No. 74141TE—Serial No. 312000001 and Up Setup Instructions Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Use Qty. No parts required – Remove parts from the crate. No parts required – Check the tire pressure. Rear wheels 2 Install the rear wheels.
PAGE 2
Procedure Description Use Qty. 16 No parts required – Check the machine before delivery to the customer. 17 Operator's Manual Engine Owner's Manual Registration Card Operator training material Key 1 1 1 1 2 Delivering the machine to the customer.
PAGE 3
5 Installing the Seat Parts needed for this procedure: Figure 3 3. Remove the wheel nuts from both sides of the vehicle and remove the right angle retaining plate. Discard the screws and retaining plate. 1 Seat 1 Seat plate 2 Guard 8 Flange nuts (5/16 inch) Procedure 1. Remove the 4 nuts holding the seat plate to the machine. Discard these nuts, they are used for shipping only. 4. Mount the wheels with the valve stem to the outside and secure them with the wheel nuts previously removed. 5.
PAGE 4
6 g017995 Checking the Seat Belt No Parts Required Procedure Important: Ensure the bolt torque is set between 49 to 61 ft-lb (67 to 83 N-m). The seat belt angle and the seat belt bolt torque need to be checked before operating. 1. Check the angle of the seat belt compared to the bottom of the seat. The angle needs to be 47 degrees. See (Figure 8). Figure 6 2. If needed, set the seat belt to the correct angle. 3. Check and set the bolt torque between 49 to 61 ft-lb (67 to 83 N-m). 4.
PAGE 5
7 Installing the Motion Control Levers Parts needed for this procedure: 1 Right control lever 1 Left control lever Bolt (3/8 x 1 inch) (2 are assembled) Nut (3/8 inch)(2 are assembled) Procedure 1. Rotate the motion control levers to the upright position. 2. Loosely install the control levers on the outside of the posts, using 4 bolts and 4 nuts. Figure 10 Note: Install the control levers in the top and middle holes for the high position or the middle and bottom holes for the low position, as desired.
PAGE 6
1 2 g016346 3 Figure 12 Figure 11 1. Lift assist pedal 3. Carriage bolt (3/8 x 1-1/2 inches) 2. Remove the air cleaner cap from the machine. 2. Flange nut (3/8 inch) 3. Install the hose clamp onto the air cleaner cap. 9 Installing the Air Cleaner Cap Parts needed for this procedure: 1 Air cleaner cap 1 Hose clamp Figure 13 Procedure 4. Install the air cleaner cap onto the air cleaner and secure it with the hose clamp. Note: Not all units come with a heavy duty air cleaner.
PAGE 7
Figure 15 2. Install the battery. Refer to Installing the Battery in the Operator's Manual for instructions. 11 Figure 14 Checking the Engine Oil Level 10 No Parts Required Procedure Charging and Installing the Battery Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Servicing the Engine Oil Level in Operator's Manual.
PAGE 8
1 2 g017435 Figure 17 3 14 4 Checking the Side Discharge Chute No Parts Required G008942 Procedure Figure 16 If there are plastic ties holding the side discharge chute up, remove them and lower the chute into place. 13 WARNING An uncovered discharge opening could allow the lawn mower to throw objects in the operator's or bystander's direction and result in serious injury or death. Also, contact with the blade could occur.
PAGE 9
Figure 18 1. Grass Deflector 4. L end of spring, place behind deck edge before installing bolt 2. Spring 5. Deck edge 3. J hook end of spring 15 Testing the Safety Interlock System No Parts Required Procedure Before using the machine, test the safety interlock system; refer to the Safety Interlock System in Operator's Manual.
PAGE 10
16 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure. Check the level of the mower. Check the mower deck idler arm for grease Check the engine oil level. Check the hydraulic fluid level.
PAGE 11
17 Delivering the Machine to the Customer Parts needed for this procedure: 1 Operator's Manual 1 Engine Owner's Manual 1 Registration Card 1 Operator training material 2 Key Procedure At delivery, Fill in the model and serial number and complete the items listed in the following table and initial each when finished. Model No. Serial No.
PAGE 12
Dealer Initial Customer Initial Check Procedure Show the customer where the following features are located and how they function: • Hour meter/ Safety Interlock Symbols/ Battery indicator/Fuel Gauge • Fuel tank cap(s) • Oil fill cap/Oil dipstick • Spark plug(s) • Engine oil filter • Engine oil drain • Fuel filter(s) • Air filter • Radiator coolant (if applicable) • Hydraulic fluid reservoir • Hydraulic filter • Battery • Ignition switch • Throttle lever • Choke (if applicable)