Form No. 3443-905 Rev A Operator's Manual FieldCombo 770 Model No. 46420—Serial No. 321000001 and Up Register at www.Toro.com/bullseye.
WARNING Model No. CALIFORNIA Proposition 65 Warning Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Serial No. This manual identifies potential hazards and has safety messages identified by the safety-alert symbol (Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions. Introduction g000502 Figure 2 1.
Safety and Instructional Decals Safety General Safety Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. This product is capable of causing personal injury. Always follow all safety instructions to avoid serious personal injury. • Read and understand the contents of both this Operator’s Manual and the operator’s manual of the traction unit before using this machine.
Setup Removing the Attachment from the Pallet The attachment is shipped vertically on the pallet. Use the following instructions to remove it from the pallet. DANGER g340175 The attachment is unstable and could swing when lifted, injuring anyone beneath it or around it. Figure 3 1. Adjustable leg • Refer to the lifting machine operator’s manual to ensure that it is rated to lift the attachment. • Ensure the lift height is kept to a minimum and only high enough to remove the shipping material.
Attaching the Brushes Checking the Ballast Requirements 1. Remove the 4 cable ties securing the brush assembly to the frame. 2. Use the 4 chains to attach the brush assembly to the frame. WARNING Mounting the machine to the rear of the traction unit decreases the weight on its front axle. Failure to add required ballast may result in an accident and severe injury or death. • To ensure adequate steering control and stability, you may need to add ballast to the front of the traction unit.
Attachments/Accessories Product Overview A selection of Bullseye approved attachments and accessories may be available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or authorized Bullseye distributor or go to www.Toro.com/Bullseye for a list of all approved attachments and accessories. To ensure optimum performance and continued safety certification of the machine, use only genuine Bullseye replacement parts and accessories.
Connecting to a 3-Point Hitch Operation Before Operation Connecting the Lower Link Arms Before Operation Safety • Never allow children or untrained people to operate or service the machine. Local regulations may restrict the age of the operator. The owner is responsible for training all operators and mechanics. 1. Ensure that the attachment is positioned on a level surface. 2. Remove the hairpin cotters and hitch pins from the attachment.
5. Secure the right and left lower link arms to the frame using the hitch pins. 3. Rotate the upper link to shorten the link. Adjust it until the attachment is flat on the ground. 4. Tighten the jam nut to secure the upper link into position. 5. Start the traction unit and lift the attachment off the ground. 6. Raise the adjustable leg. g348396 g340159 Figure 8 1. Lower link arm (2) 6. Figure 10 2. Hitch pin and hairpin cotter (2) 1.
4. • Slow down and use caution when making turns Verify the working depth while the attachment is stationary. and crossing roads and sidewalks with the machine. Always yield the right-of-way. • Reduce speed on rough roads and surfaces. • When the attachment is connected to a traction Transporting the Attachment unit and in the raised position, the weight of it affects stability, braking, and steering. Exercise caution when transporting between working areas.
After Operation Tall grass can hide obstructions. Uneven terrain could overturn the machine. • Be aware that operating the machine on wet After Operation Safety grass, across slopes, or downhill may cause the machine to lose traction. Loss of traction to the drive wheels may result in sliding and a loss of braking and steering.
4. 9. Lower the adjustable leg and lock it with the pin and hairpin cotter. 10. Remove the upper link. Remove the lower link arms. Important: Ensure that the attachment does not slide off the traction unit and cannot roll away. g340175 Figure 13 1. Adjustable leg 2. Pin 5. Lower the attachment to the ground. 6. Loosen the upper link jam nut and rotate the upper link. g348396 Figure 15 1. Lower link arm (2) 11. g348397 Figure 14 1. Upper link 3. Hairpin cotter 2. Jam nut 4. Link pin 7.
. Install the hitch pins to the attachment and secure them with the hairpin cotters. g348398 Figure 16 1. Hairpin cotter (3) 2. Hitch pin (3) Important: When storing the attachment, do not allow the spring pins or brush to touch the ground or other objects to avoid bending the pins or bristles.
Maintenance CAUTION If you leave the key in the switch, someone could accidently start the engine and seriously injure you or bystanders. Remove the key from the traction unit switch before you perform any maintenance. Maintenance Safety Replacing the Spring Pins • Before adjusting, cleaning, servicing, or leaving As you use the attachment, the spring pins will wear. Replace worn spring pins. the machine, do the following: – Position the machine on a level surface. 1.
g351040 Figure 18 1. Nut 2. Spring pin 5. Remove the existing pin and insert a new pin. 6. Tighten the nut. 7. Thread the rope through the spring pin loops and tie a knot to secure it to the pin on the end as shown in Figure 17.
Troubleshooting Problem The attachment loosened too little material. The appearance of the field is poor. Possible Cause Corrective Action 1. The working depth is set too shallow. 1. Increase the working depth. 2. The infill material is too compacted. 2. Drive multiple passes over the turf, each with a deeper setting. 1. The working depth is set too deep. 1. Decrease the working depth. 2. The drag brush does not drag over the ground. 2.
Notes:
Notes:
Notes:
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
Warranty Statement One-Year Limited Warranty Conditions and Products Covered Parts Your Bullseye product (“Product”) is warranted to be free from defects in materials or workmanship for 1 year. Where a warrantable condition exists, we will repair the Product at no cost to you including diagnostics, labor, parts, and transportation. This warranty begins on the date the Product is delivered to the original retail purchaser.
