Operator’s Manual & Parts List MODEL 891 POLYMER INJECTOR PUB. NO. 0970 THIS COMPANY RESERVES THE RIGHT TO DISCONTINUE ANY MODEL OR PRODUCT, ADD IMPROVEMENTS TO, OR CHANGE THE DESIGN AT ANY TIME WITHOUT OBLIGATION TO IMPROVE EXISTING MACHINES, EITHER BY CHANGING THE DESIGN OR ADDING NEW PARTS. . RECORD IN THE SPACE PROVIDED BELOW THE MODEL NUMBER AND THE SERIAL NUMBER OF THIS UNIT, PLEASE RETAIN THESE NUMBERS FOR FUTURE i REFERENCE, MODEL NUMBER SERIAL NUMBER THIS MANUAL COVERS MODELS WITH SERIAL NC.
PERFORMANCE GUARANTEE LOATHE MANUFACTURING, INC. of Lathe, Kansas, provides warranty to the original purchaser of a new Lathe product, that the same is free from defects in workmanship or material that may cause performance failures, subject to the conditions sated herein. ‘The warranty is limited to a period of one (1) year from the date of purchase, If used for rental purposes, the period of time is one hundred eighty (180) days. Lathe Manufacturing, Inc.
TABLE OF CONTENTS GENERAL INFORMATION SPECIFICATIONS 1. oiiitinimtti i et magician e e SETUP INSTRUCTIONS . 5 OPERATING CAUTIONS Lott in it annals 5 OPERATING INSTRUCTIONS SOFT SURFACE . OPERATING INSTRUCTIONS HARD SURFACE PREVENTIVE MAINTENANCE & LUBRICATION .. ILLUSTRATED PARTS: MAINFRAME ASSEMBLY HAND NOZZLE & HOSE CONNECTION . HARD SURFACE NOZZLE.
GENERAL INFORMATION The hand held Model 891 Polymer Injector makes it feasible and practical to utilize long-lasting water absorbing polymers in the root system of plants, shrubs, and trees. The polymer forms a water reservoir, with the plant roots growing through it absorbing water as needed.
SET UP INSTRUCTIONS ‘Upon delivery of the unit, please inspect for any damages that may have occurred during shipment, or for any pans that may have been lost in shipment. Also check all bolts and fasteners for tightness. Please make any claim immediately upon inspection to the carrier. ‘The Model 891 is shipped fully assembled. Go through the Owners Manual and check all tolerances and familiarize yourself with the machine. Read the engine manual carefully and service accordingly.
5. Slowly pull the trigger back while pushing downward into the soil until desired depth is achieved. Hold handle back until the appropriate amount of polymer is in the ground. The solution is being pumped at a rate of nine (9) gallons per minute. 6. Let the injector gun remain in the sol a few seconds before pulling it out. This releases all the solution out of the gun and prevents it from spraying the operator. OPERATING INSTRUCTIONS HARD SURFACE 1.
PREVENTIVE MAINTENANCE Regular maintenance will result in a smoother running, more efficient, longer lasting machine. If wom or damaged parts are found in your inspection, replace them immediately, Remember .. . . any machine, regardless of design or type will perform only in reflation to the service it receives. 1. Change oil in the Briggs engine after the first five hours of operation. Thereafter change the il every S0 hours of operation under normal operating conditions. 2.
MAIN FRAME ASSEMBLY ITEM PART PART NAME ary. NO. NUMBER AND DESCRIPTION L -290. TANK 110gal. . 1 2 01-270-2580 ENGINE, 5 HP Briggs & Castration 1 1.368.001 Tie DOWN KIT, Ratchet (Not Sh 1 3. 913050720 PUMP 011780510 HAS, 5167 18X 1.1 4 8 01-165-0500 FLAT WASHER, 5/16° . 2 & 01-166-0510 LOCK WASHER, /16 4 7. 01-188-0518 HEX NUT 6/16*18 4 8 89-105-0012 MAIN FRAME . 1 9. GROMMET 89-105-0051 SKID BRACKET .
HAND NOZZLE & HOSE CONNECTION ITEM PART PART NAME Arty. NO. NUMBER ARD DESCRIPTION 1 01-455-0070 ELBOW, 01-217-0110 RC NIMBLE, 1* 3 01-202-0080 CLAMP . 1 01-312-1800 HOSE, 1" x4 5. 014500170 SEDUCER, 1 & 01-217-0210 KC NIPPLE, /4" 7.
