Installation Instructions

ManualsBrandsToro ManualsAttachments67 Blower Mounting Kit, Groundsmaster 300 Series

1 67-005-2371 Toro Hydraulic Bracket 1

2 01-168-2018 Machinery Bushing 1(var)

3 01-168-2014 Machinery Bushing 2(var)

4 67-004-2671 PTO Adapter 1

5 67-004-1011 PTO Guard 1

6 95-0078 Mount - Upper WA 1

7 3253-6 Lock Washer 2

8 3256-6 Flat Washer 8

9 3217-8 Hex Nut 2

10 3217-9 Hex Nut 2

11 3272-11 Cotter Pin 2

12 3253-7 Lock Washer 2

13 323-13 Capscrew - Hex Hd. 1

14 01-506-0130 Decal - Danger 1

15 67-004-0401 Upper Support Hinge Rod 1

16 67-004-1512 Lower Lift Arm Bracket 1

17 98-6160 Bracket - Mount 2

18 325-5 Capscrew - Hex Hd. 4

19 58-6520 Decal - Grease 1

20 323-8 Capscrew - Hex Hd. 2

21 3256-4 Flat Washer 8

22 3253-5 Lock Washer 2

23 3217-7 Hex Nut 4

24 324-6 Capscrew - Hex Hd. 2

25 3256-5 Flat Washer 8

26 32153-5 Nut - Side Lock 4

27 92-4664 PTO - Female Half 1

PARTS LIST &

ASSEMBLY

INSTRUCTIONS

67 BLOWER MOUNTING KIT

for 300 SERIES GROUNDSMASTER

Note: This bracket must be

installed when mounting

blower to a 300 Series

Groundsmaster with an 88"

mowing deck.

NOTE: If you are mounting the blower on a unit that has a

72" Recycler deck, you will need to replace the short male

end of the PTO with the longer male end, part number

92-4663.

MODEL NO. 44535

FORM NO. 95-0118 Rev. D

MOUNTING KIT

67-006

Ref.

No.

Part No.

Description

No.

Used

Ref.

No.

Part No.

Description

No.

Used

The TORO Company - 1996

All Ri

ese

Summary of content (8 pages)

PAGE 1
FORM NO. 95-0118 Rev. D MODEL NO. 44535 PARTS LIST & ASSEMBLY INSTRUCTIONS 67 BLOWER MOUNTING KIT for 300 SERIES GROUNDSMASTER® Note: This bracket must be installed when mounting blower to a 300 Series Groundsmaster with an 88" mowing deck. MOUNTING KIT Ref. No. Part No.
PAGE 2
WEIGHT ASSEMBLY Ref. No. 1 2 3 2 Part No. Description 67-004-1521 Weight 323-11 Capscrew - Hex Hd. 3256-4 Flat Washer No. Used Ref. No. 1 2 2 4 5 Part No. 3253-5 3217-7 67-008 Description Lock Washer Hex Nut No.
PAGE 3
(Intentionaly Left Blank) Ref. No. Part No. Description No. Used Ref. No. Part No. Description No.
PAGE 4
ASSEMBLY INSTRUCTIONS 67 BLOWER MOUNTING KIT 1. Attach the lower lift arm bracket to the rear housing as shown in Fig. 1. Fasten with a 1/2" lock washers and nuts. Tighten all nuts. 12. Have a helper push down on the left push arm; then insert a 2" x 4" block of wood between the frame and the top of the push arm. 2. Attach the PTO adapter and machinery bushings to the fan shaft, lining up holes in each. 13. Pull down the right push arm until it is level with the left push arm.
PAGE 5
Lower Lift Arm Bracket Upper Support Hinge Rod Bracket - Mount PTO Adapter PTO Guard PTO Mount - Upper WA Figure 1 5
PAGE 6
NOTES 6
PAGE 7
NOTES 7
PAGE 8
MAINTENANCE RECORD Date