FORM NO. 01-502-1680 OPERATOR'S MANUAL THATCHING REEL 87 ATTACHMENT FOR TURF SWEEPER 6500 MODEL NQ.
FOREWORD Thank you for buying a high quality Toto turf care product. To get the best performance from this machine, operate and maintain it according to the instructions in this manual. Taro also wants to stress the importance of safety. You and anyone else using or maintaining this machine are strongly urged to read this manual, especially all the safety instructions. DANGER, WARNING and CAUTION, used with the triangular safety alert symbol, highlight safety messages.
TABLE OF CONTENTS Page Page SAFETY INSTRUCTIONS .. 3 LUBRICATION 11 SAFETY AND INSTRUCTION DECALS. 4 STORAGE ..o, 11 SPECIFICATIONS 5 PARTS ORDERING 1 SET UP INSTRUCTIONS .. 8-10 THE COMPROMISE .. .. Back Cover OPERATING INSTRUCTIONS 10 SAFETY INSTRUCTION The safety alert symbol means CAUTION, WARNING or DANGER “personal safety instruction, Read and understand the instruction because it has to do with safety. Failure to comply with the instruction may resulting personal injury. BEFORE OPERATING 1.
SAFETY AND INSTRUCTION DECALS The following safety and instruction decals are installed on the unit. Replace any decals that becomes damaged or illegible. Part numbers for decals are listed below and in your Parts Catalog. Order replacements from your Authorized Toto Distributor. (263 CAUSE TIBERIUS :PERSONAL-INJURY QLB LN iR ON CHAIN GUARD (Part No. (1-506-0050) EACH SIDE BLADE GUARD {Part No.
SPECIFICATIONS THATCHING WIDTH: 60" MOUNTING REQUIREMENTS: Model 65 Sweeper OPERATION: PTO powered, chain driven. ROTATION DIRECTION: Forward RAISE/LOWER MECHANISM: Screw jack BLADES: {19) 12 pt., centers. DRIVE CHAINS: #80 chain BEARINGS: All self-aligning, re-lube type. DIVERSIONS: Height 20" Width 69" Length 24" SHIPPING WEIGHT: 310 Ibs.
SET UP INSTRUCTIONS NOTE:This unit is heavy and the blades are capable of causing serious injury. Iris recommended that two men mount this unit and that caution be exercised during this mounting procedure. 1. Take note of the parts already assembled on your thatcher and familiarize yourself with the hardware and parts needed to complete the assembly of the thatcher. (F1G. 1) With two or more men, lift the Blade Support to the Reel Housing assembly.
SET UP INSTRUCTIONS {Cont.) 3. (FIG. 2} install the Screw Jack assembly as 4. (FIG. 3} Remove the gearbox guard and the shown in the illustration. A hole for the caste nut existing PTO from the tractor. Attach the drive must be drilled for a cotter pin to secure its position. shaft, the U-joint and the bearing. The spade lug, is an adjustment for the bearing and will be adjusted later.
SET UP INSTRUCTIONS (Cont.) 4) Assemble the gear train of the thatcher. Note the relative positions of the gears and chains, item A {sprocket} has a grease zero which must go to the outside. After the gears are placed on the shafts with the keys, a 3/16" hole must be drilled in the shafts to accommodate cotter pins (item BJ. Space machinery bushings out t©o the hole to keep the sprocket from moving outward, MACH.
SET UP INSTRUCTIONS {Cont.) 8. (FIG. 5 Attach the PTO extension shaft (item A} and U-joint (item B), along with the mounting angle (tem C), bearing lite: DY and the blade guard {item E} to the gearbox as shown in the illustrated parts. Hook up the tractor PTO to the PTO extension. NOTE:Be sure that when raising the thatcher, the blades do not come in contact with the blade guard (item E). Adjust the jack so the blades will stop short of the guard. 9. Test the operation of the unit in the raised position.
SET UP INSTRUCTIONS (Cont.) 10. {FIG. 6} Install the thatcher guards according Reinstall the gearbox guard, The unit should now to the illustration, using the hardware shown, be ready to field test. Figure @ OPERATING INSTRUCTIONS 1. This unit is capable of thatching dead grass, 3. Choose a test patch of ground to experiment for debris, etc., or if dowered into the ground, aerating the right depth to achieve satisfactory results. several inches deep. 2.
LUBRICATION BEARINGS The thatcher has self sealing bearings thalamus DRIVE CHAIN 1. Always maintain a heavy coat of grease on the lubricated with a No. 2 Lithium based grease. drive chain. IMPORTANT: Lubricate the bearings to maintain a slight leakage on the seals. Too much grease can cause overheating. STORAGE 1. Thoroughly clean the thatcher. The blade area should be free of dirt, leaves and debris, 2. Check the condition of the blades. Replace any worn or broken blades. 3.
L. The Moro Promise A ONE YEAR LIMITED WARRANTY The Toto Company promises to repair your TOR Product if defective in materials or workmanship. Commercial Products . The following time periods from the wade of purchase apply: The costs of parts and labor are included, but the customer pays the transportation costs on walk rotary mowers with cutting widths of less than 25" If you feel your TOR products defective and wish 1o rely on The Toto Premise, the following procedure is recommended: .
