Quick Start Guide

ManualsBrandsToro ManualsRiding ProductsX30 GeoLink Precision Spray System Kit

FormNo.3397-442RevB

GeoLink

PrecisionSpraySystem

MultiPro

5800TurfSprayer

ModelNo.41623

QuickStartGuide

ContactToroNSNat1-844-GeoLink(1-844-436-5465)orNSNTech@toro.comforcustomerservice.

Note:Whenyouturnonthedisplayforthersttime,itisinstandardmode.Ensurethemachineisstoppedwhilechanging

thedisplayandconguration.

UsingtheTouchScreen

Sprayerinformationisaddedtothescreenwhenyoutouchandenabletheindividualicons.

•Selectanyicononthescreentodisplaywhatisshownonthescreen.

•Pressonanicontochangeit,andfurtheroptionswilldisplay.

•Selecttheoptionsasrequiredandconrmthenewdisplay(Figure1).

g032674

Figure1

g031287

16 15

Figure2

Easy-modescreen

1.System-informationicon

5.Inventory-managericon9.Job-menuicon

13.Screen-viewicon

2.Guidanceicon6.Setupicon

10.Field-menuicon

14.Center-mapview

3.Job-informationicon7.Sprayerdashboard

11.Job-assistanticon15.Boundary-selectionicon

4.Sprayer-controllericon

8.Master-switchicon

12.Zoom-functionicon

16.Boom-displayicon

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3397-442*B

Summary of content (4 pages)

PAGE 1
Form No. 3397-442 Rev B GeoLink® Precision Spray System Multi Pro® 5800 Turf Sprayer Model No. 41623 Quick Start Guide Contact Toro NSN at 1-844-GeoLink (1-844-436-5465) or NSNTech@toro.com for customer service. Note: When you turn on the display for the first time, it is in standard mode. Ensure the machine is stopped while changing the display and configuration. Using the Touch Screen Sprayer information is added to the screen when you touch and enable the individual icons.
PAGE 2
Entering a Product and Tank Volume 3 2 1 1. Select the sprayer-controller icon. 2. Expand the sprayer-controller panel. 3. Select the product title, finish the wizard for rate, and confirm (Figure 3). 2 g031480 Figure 4 1. Field-menu icon 2. New-field icon 3. Field name Creating New Field Boundaries in Standard Mode 1 3 Note: Ensure that the display is in standard mode to create boundaries. Note: Ensure the units are correct for your use.
PAGE 3
1 8. When finished spraying border, select the create boundary from coverage icon. 9. To only spray within the border, select the auto-section control icon and change the boundary limit to field boundaries. Naming and Categorizing a Field Boundary 1. After creating a boundary, hold your finger on the boundary line. 2. When the boundary line is highlighted, remove your finger from the screen and the properties menu will open. 3.
PAGE 4
3 1 1 2 g031485 g031494 4 3 Figure 9 2 1. Job-menu icon Figure 7 3. Select the job region 2. Configure-job regions icon 3. Decrease and increase icons 4. Sprayer-controller icon 1. Current rate 2. Preset-rate icons 10. Select the excluded regions that are not to be sprayed (bunkers, trees, hazards, etc.) 6. Select the job-menu icon in the upper right of the screen. Note: Refer to the standard mode videos for spraying a boundary inside another boundary. 7.