Installation Instructions

ManualsBrandsToro ManualsSprayersEnclosed Boom Mount, Workman 200 Spray System

Form No. 3354-221 Rev A

Enclosed Boom Mount Kit

For Workman 200 Spray System

Model No. 41363 —Serial No. 260000001 and Up

Operator's Manual

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

No parts required

–

Prepare the machine.

Slotted bracket

Bolt (1/2 x 1-1/2 inches)

Lock nut (1/2 inch)

Install the slotted bracket.

Center boom mount assembly

Bolt (1/2 x 1-1/4 inches)

Lock nut (1/2 inch)

Install the center boom mount

assembly.

Bracket mount, ow meter

Bolt (1/2 x 1-1/4 inches)

Lock nut (1/2 inch)

Install the ow meter mount.

No parts required

–

Identify the actuator connectors.

Step

Preparing the Machine

No Parts Required

Procedure

1. P ark the spra yer on a ﬂat surface , lo w er the

booms , set the parking brak e (if installed), stop

the engine , and remo v e the k ey .

2. Empty the contents of the tank. R efer to the

Operator’ s Manual for more infor mation.

Chemicals ar e hazardous and can cause

per sonal injur y .

• R ead the dir ections on the chemical

la bels bef or e handling the chemicals

and f ollo w all man uf actur er

r ecommendations and pr ecautions.

• K eep chemicals a w ay fr om y our

skin. Should contact occur , w ash the

af fected ar ea thor oughl y with soap

and clean w ater .

• W ear go g g les and an y other pr otecti v e

equipment r ecommended by the

chemical man uf actur er .

3. Disconnect and remo v e any existing spra y

booms to pre pare the mac hine for the new

enclosed boom system. Disconnect the hoses

at the boom extensions , not the v alv es . R etain

all par ts and fasteners for later installation if

necessar y .

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Summary of content (4 pages)

PAGE 1
Enclosed Boom Mount Kit Form No. 3354-221 Rev A For Workman 200 Spray System Model No. 41363—Serial No. 260000001 and Up Operator's Manual Installation Loose Parts Use the chart below to verify that all parts have been shipped. Step 1 2 3 4 5 Description Qty.
PAGE 2
Step Step 2 3 Installing the Slotted Bracket Installing the Center Boom Mount Assembly Parts needed for this step: Parts needed for this step: 2 4 4 1 4 4 Slotted bracket Bolt (1/2 x 1-1/2 inches) Lock nut (1/2 inch) Center boom mount assembly Bolt (1/2 x 1-1/4 inches) Lock nut (1/2 inch) Procedure Procedure 1. Locate the slotted brackets in loose parts. Install a slotted bracket to each side of the frame (Figure 1).
PAGE 3
Step 4 Installing the Flow Meter Mount Parts needed for this step: 1 2 2 Bracket mount, ow meter Bolt (1/2 x 1-1/4 inches) Lock nut (1/2 inch) Procedure Figure 4 Install the ﬂow meter bracket to the top of the left boom frame upright using two bolts (1/2 x 1-1/4 inches) and two lock nut (1/2 inch) as shown in Figure 3. 1. 2. 3. Left boom frame Hose reel frame Flow meter bracket 4. 5.
PAGE 4