Software Guide

ManualsBrandsToro ManualsSprayersMulti Pro 1750 Turf Sprayer

Table Of Contents

FormNo.3409-678RevB

MultiPro

1750TurfSprayer

ModelNo.41188—SerialNo.400000000andUp

SoftwareGuide

Readthisinformationcarefullytolearnhowtooperateandmaintainyourproductproperlyandtoavoidinjury

andproductdamage.Youareresponsibleforoperatingtheproductproperlyandsafely.

Wheneveryouneedservice,genuineT oroparts,oradditionalinformation,contactanAuthorizedServiceDealer

orT oroCustomerServiceandhavethemodelandserialnumbersofyourproductready.

YoumaycontactT orodirectlyatwww.T oro.comforproductsafetyandoperationtrainingmaterials,accessory

information,helpndingadealer,ortoregisteryourproduct.

Introduction

Thisguideprovidesinformationforusingsprayer

systeminformationandcontrollingsprayersystem

functions.

Contents

Introduction...............................................................1

Setup........................................................................1

BeforeYouBeginSpraying.................................1

ProductOverview.....................................................2

Controls.............................................................2

Operation..................................................................4

BeforeOperation...................................................4

StartingtheInfoCenter........................................4

InfoCenterMainSubMenus...............................5

CalibratingtheSprayer......................................11

EnteringtheSprayT ankVolume........................11

DuringOperation.................................................12

InfoCenterSprayAreaScreens........................12

InfoCenterAdvisories.......................................13

Maintenance...........................................................14

ServiceScreens...............................................14

DiagnosticsScreens.........................................15

AboutScreens..................................................17

Setup

BeforeYouBeginSpraying

PreparingtheMachine

1.Fillthesprayertankandfreshwatertank;refer

tollingthespraytankandllingthefresh-water

tankproceduresintheOperator’sManual.

2.Calibratethemachine;refertotheMultiPro

1750TurfSprayerOperator’sManualfor

informationaboutcalibratingthemachine.

3.Enterthecorrectvolumeofliquidinthespray

tank;refertoEnteringtheSprayT ankVolume

(page11)

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3409-678*B

Summary of content (20 pages)

PAGE 1
Form No. 3409-678 Rev B Multi Pro® 1750 Turf Sprayer Model No. 41188—Serial No. 400000000 and Up Software Guide Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready.
PAGE 2
Product Overview • Middle selection button—use this button to scroll Controls • Right selection button—use this button to open InfoCenter Home Screen Note: The purpose of each button may change down menus. a menu where a right arrow indicated additional content. depending on what is required at the time. Each button has an icon displaying its current function. When you start the machine, the home screen appears, displaying the corresponding icons that apply (i.e.
PAGE 3
InfoCenter Icon Descriptions Icon Full spray tank Description Spray tank at half Information icon Next Tank level low Previous Empty spray tank Scroll down TURF units (1,000 ft²) or Enter Area sprayed Change the next value in the list Increase Volume sprayed Decrease Active screen Adjust tank volume Inactive screen Home screen Go to the home screen Clear active area Active home screen Clear all areas Save value Adjust digit Exit menu Select the next area for accumulation Hour meter
PAGE 4
Operation button to display the information context (Figure 4). Before Operation Starting the InfoCenter 1. Insert the key into the starter switch and rotate it to the ON position. The InfoCenter illuminates and displays the initialization screen, which displays voltmeter and hourmeter information (Figure 2). If you have the GeoLink system equipped, the initialization screen shows the GeoLink logo instead of the Toro logo (Figure 3).
PAGE 5
InfoCenter Main Sub Menus Service Using the Menus To access the InfoCenter menu system, press the menu access button while at the main screen. This will bring you to the main menu. Refer to the following tables for a synopsis of the options available from the menus: Menu Item Description Faults Displays the most recent faults and last cleared fault. Hours Lists the total number of hours for key on, machine run, and pump on. It also lists the service due hour and service reset.
PAGE 6
Calibration Setting the Hill Assist Function Note: Machines with the GeoLink system installed Hill assist is set to ON by default, but you can turn it off as follows: and enabled cannot access the Calibration sub menu. The calibration function is maintained by the GeoLink system. 1. To access the calibration settings, use the middle selection button to navigate to the CALIBRATION , then press the right button to enter into the calibration screen (Figure 5).
PAGE 7
(the button below the down arrow icon in the display) to move the selected option down to the Backlight or Contrast setting (Figure 10). Changing the Units of Measure 1. 2. To change the unit of measure, use the middle selection button to scroll to the UNITS option Figure 9. Press the right selection button to change the listed units of measure (Figure 9).
PAGE 8
4. Note: As you change the brightness or contrast • Press the center selection button (B of Figure value, the display changes the value of the selected level. 11) to increase the numerical value (0 to 9). • Press the right selection button (C of Figure 11) to move the cursor to the next numerical position to the right. Once the right-most value is set, press the right selection button. Press the left selection button to save your selection (Figure 10). 4.
PAGE 9
6. Wait until the InfoCenter displays the “value saved message” and the red indicator light illuminates. Setting the Protect Settings Important: Use this function to lock and unlock the application rate. Note: You must know the 4-digit PIN number to change settings for functions in the protected menus. 1. g028523 Figure 14 Press the center selection button to highlight the Protect Settings entry. 8.
PAGE 10
• L Boom—80 in • C Boom—60 in • R Boom—80 in 1. Use the middle selection button to navigate to the RESET DEFAULTS option. 2. Press the right selection button to enter into the Reset Defaults screen. 3. Press the center selection button for YES or the left selection button for NO. Note: Selecting YES will reset the settings listed above.
PAGE 11
Diagnostics Calibrating the Sprayer To access the Diagnostics screen, use the middle button to navigate to the DIAGNOSTICS option, then press the right button to enter into the Diagnostics screen (Figure 18). Refer to the Multi Pro 1750 Turf Sprayer Operator’s Manual for information on calibrating the sprayer. Entering the Spray Tank Volume Use the spray tank volume screen to enter the amount of water filled into the tank before you begin spraying. To access the spray tank volume screen: 1.
PAGE 12
3. Using the Sub-Area Screen Use the center selection button and right selection button to adjust the tank volume (Figure 21). The sub-area screen displays the area and the amount of product sprayed in sub-areas (Figure 23). • Use an individual sub-area for each sprayer job at your site. You can use up to 20 sub-areas to collect sprayer information for the sprayer jobs at the site.
PAGE 13
Note: The number shown in the box, located in the upper right corner of the screen, indicates the active sub-area where area and volume information are being collected. Advisories (cont'd.) Advisory Code Description InfoCenter Advisories 203 Start Prevented—Throttle pedal is not home 204 Start Prevented—Starter engage timeout Operator advisories automatically display on the InfoCenter screen when a machine function requires additional action.
PAGE 14
Maintenance Service Screens To access the Service screen, use the middle button to navigate to the SERVICE option, then press the right button to enter into the Service screen (Figure 25). g203637 Figure 27 1. Fault items The list below identifies the fault codes that are generated by the Toro Electronic Controller (TEC) to identify an electrical system malfunction that occurred during machine operation. Follow the steps listed above to view the faults.
PAGE 15
Viewing the Service Hours 1. Use the middle selection button to navigate to the HOURS option (Figure 28). g203665 Figure 30 FLOW CAL VALUE selected g202880 Figure 28 2. 2. Press the right selection button to enter into the Hours screen. 3. Use the counter information displayed on the screen (Figure 29) to determine the following: Press the right selection button to select the FLOW RATE , FLOW CAL VALUE, or SPEED CAL VALUE option.
PAGE 16
Pumps The Pumps screen identifies the requirements necessary to allow operation of the spray pump and the optional rinse pump. To navigate to the Pumps screen, use the middle selection button to highlight the PUMPS option, then press the right selection button to enter into the Pumps screen (Figure 32).
PAGE 17
About Screens Engine Run Parameters Table Inputs Qualifiers Outputs Key Start Neutral Switch OK RUN Key Run Seat Switch or Parking Brake Switch Starter Output Information in the About screen includes the model number, serial number, and the revision number of the software version. 1. Pump Switch OFF To access the about screen, use the middle button to navigate to the ABOUT option, then press the right button to enter into the About screen (Figure 36).
PAGE 18
Notes:
PAGE 19
Notes:
PAGE 20