Form No. 3393-275 Rev A EU Compliance Kit 2015 and After Multi Pro® 1750 Turf Sprayer Model No. 41155—Serial No. 315000001 and Up Operator's Manual Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 illustrates the location of the model and serial numbers on the product.
Hand Sprayer Safety Chemical Safety • Do not aim the hand sprayer at any person or animal. WARNING Fluids under high pressure can penetrate skin and cause severe injury, possibly resulting in amputation or death. Hot liquids and chemicals can also cause burns or injury. If any part of the body comes in contact with the spray stream, immediately consult a physician familiar with injected fluid injuries.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 120-0687 120-0673 1. Boom spray 1. Valve, open 2. Valve, closed 3. Hand spray 2. Rinse Tank Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Use 1 No parts required – Prepare the machine.
Procedure 3 4 5 6 7 Description Qty.
Procedure 8 9 10 11 12 13 14 15 Description Use Qty. Inlet hose 2.5 x 66 cm (1 x 26 inch) Hose clamp 90° hub fitting Large O-ring T-Fitting (upper) Retainer Reducer hub Small O-ring Transfer hose 1.9 x 61 cm (3/4 x 24 inch) Hub connector Hose clamp Retainer Hose 1.9 x 76 cm (3/4 x 30 inch) Hose clamp Hose 1.9 x 61 cm (3/4 x 24 inch) Hose clamp Hose 1.9 x 48.3 cm (3/4 x 19 inch) Hose 1.9 x 61 cm (3/4 x 24 inch) Tee fitting Hose clamp Hose 1.
1 2 Preparing the Machine Installing the Rinse Tank No Parts Required Parts needed for this procedure: 2 Carriage bolt (5/16 x 1 inch) 1 Spray-gun bracket 2 Clamp 2 Flanged locknut (5/16 inch) 1 Carriage bolt (3/8 x 1 inch) 2 Carriage bolt (3/8 x 1-1/4 inch) 3 Flange locknut 1 Rinse tank 1 Filler cap 1 Bulkhead fitting 1 Plastic flange nut Chemicals are hazardous and can cause personal injury.
Note: Retain the bolt (3/8 x 5 inch), washers, and flanged locknut; discard the short carriage bolt and locknut holding the R-clamp in place. Figure 3 1. Fresh water tank 3. Flanged head bolts 2. Mounting bracket 3. Remove the tank from the machine (Figure 3). Figure 5 Note: Retain the fresh water tank and flanged head bolts for installation in Installing the Fresh Water Tank (page 10). 1. Locknut 2. R-clamp 5. Washer 6. Flanged locknut 3. Carriage bolt (short) 7. Right, front tank strap 4.
Installing the Tank 4. Install 1 carriage bolt (3/8 x 1-1/4 inch) in the upper-inboard holes of the right, front tank strap (Figure 6). 1. Install the bulkhead fitting into the rinse tank as follows: Note: Loosely thread a flanged locknuts (3/8 inch) onto the carriage bolt. A. Install the flanged seal onto the bulkhead fitting (Figure 8). 5. Install 1 carriage bolts (3/8 x 1-1/4 inch) in the lower-outboard holes of the right, front tank strap (Figure 6).
3 G014260 2 1 3 Figure 12 1. Retainer G014229 3. 90° barbed fitting 2. Bulkhead fitting 1 2 2. Release the 2 latches that secure the guard behind the seat to the chassis and remove the guard from the machine (Figure 13). Figure 10 3. Filler cap 1. Bulkhead fitting (wire attached) 2. Outlet (bottom of the tank) E. Move the bulkhead fitting into position making sure that the flanged gasket seats against the interior wall of the rinse tank (Figure 10) F.
Figure 14 1. Left tank bracket (slotted flange angled down from right to left) 3. Carriage bolt (3/8 x 1 inch) Figure 15 2. Flanged locknut (3/8 inch) 5. Align the left tank bracket onto the carriage bolt (3/8 x 1 inch) at the upper-inboard holes of the left, front strap (Figure 14). 1. Flanged locknut (3/8 inch) 4. Right tank bracket (slotted flange angled down from left to right) 2. Hose mount 5. Carriage bolt (3/8 x 1-1/4 inch) 3.
Installing the Nozzles 3 Note: Apply PTFE tape to the threads of the taper-threaded fittings used in the sprayer and rinse systems. 1. Assemble the 2 rinse nozzles as shown in Figure 17. Installing the Rinse Nozzles Parts needed for this procedure: 2 90° barbed fitting (3/4 inch NPT x 3/4 inch) 2 Plastic flange nut 2 Bulkhead fitting 2 Rinse nozzle 2 Bushing 2 Rinse vane 2 Shoulder bolt 1 2 3 4 Drilling the Main Tank 1. Open the tank lid and remove the strainer basket. 5 2.
2. Install 1 carriage bolt (3/8 x 1 inch) in the upper-inboard holes of the right, rear tank strap (Figure 20). 5. Install a 90° barbed fitting (3/4 inch NPT x 3/4 inch) onto each of the threaded openings of the rinse-nozzle bulkheads (Figure 19). 1 Note: Loosely thread a flanged locknuts (3/8 inch) onto the carriage bolt. 2 1 2 3 G022283 Figure 19 1. 90° barbed fitting (3/4 inch NPT x 3/4 inch) 1 2. Rinse-nozzle assembly 4 g024697 Figure 20 6.
3 2 1 8 7 g024704 Figure 21 1. Straight-barbed fitting (1/2 inch NPT x 1/2 inch) 1 3. Nipple (1/2 inch NPT x 1/2 inch) 5 6 g025042 Figure 23 2. Pressure filter 2. Assemble the pressure-filter assembly onto the rinse pump at the nipple (Figure 22). Note: When the nipple is tight, ensure that the filter and pump are aligned vertically. 1 3 4 2 2 1. Serrated-flange nut (1/4 inch) 5. Rinse-pump cover 2. Rinse-pump mounting bracket 3. Rinse pump 6. Hairpin 4. Bolt (1/4 x 1-3/4 inch) 8.
2. Insert 4 bolts (6 x 16 mm) and 4 washers (6 mm) into the slots of the 4-way valve (Figure 25).
1 2 3 g024700 Figure 27 1. Flange locknuts (5/16 inch) 3. Faceplate bracket Figure 28 2. Flange bolts (5/16 x 1 inch) 1. Prop rod (operator’s seat) 4. Carriage bolt 2. Flanged locknut 5. Positive battery cable 3. Positive battery terminal 6 2. Remove the flanged locknut, carriage bolt, and positive battery cable from the battery (Figure 28). 3. Locate the plug where you will install the rinse-tank switch at the left side of the console (Figure 29).
6. Remove the plastic tie that secures the rinse tank connector to the wiring bundle and route the connector to the opening that you made in the console. 7. Through the opening in the console, connect the 8-pin connector of the 3-position rocker switch into the 8-socket rinse tank connector (Figure 29). 8. Push the switch into the opening in the console until the switch snaps into position. Connecting the Rinse Pump Connector 1.
4 3 2 1 3 g024826 Figure 33 1. Bolt (5/16 x 5/8 inch) 3. Straight-barbed fitting (1-1/4 inch NPT x 3/4 inch) 2. Ball valve bracket 4. Ball valve 6. Install the ball valve and valve mount bracket to the machine with 2 hex-head bolts (6 x 16 mm) and 2 flange nuts (6 mm) (Figure 34). 1 2 Figure 32 1. Right-boom mount (supporting the center boom section) 5. 15.2 cm (6 inch) 2. Ball-valve bracket 6. Mounting plate (right frame channel) 3. Drill and 6.5 mm (1/4 inch) drill bit 4. Line 7.
8 Installing the Upper Tee Assembly Parts needed for this procedure: 1 Inlet hose 2.5 x 66 cm (1 x 26 inch) 2 Hose clamp 2 90° hub fitting 4 Large O-ring 1 T-Fitting (upper) 3 Retainer 1 Reducer hub 1 Small O-ring 1 Transfer hose 1.9 x 61 cm (3/4 x 24 inch) 1 Hub connector Removing the Inlet Hose 1. Remove the flange clamp, gasket, flanged elbow, and inlet hose from the pressure filter head (A of Figure 35). Figure 35 Note: Retain the gasket and flange clamp for installation later. 1.
Assembling the Upper T-fitting, Inlet Hose and Ball Valve Hose Note: To insert the barbed fitting into the hose more easily, apply a light coat of a non-petroleum-based lubricant, such as vegetable oil to the barbed end of the fitting. 1. Insert the flanged elbow that you removed in step 3 of Removing the Inlet Hose (page 18) into the inlet hose 2.5 x 66 cm (1 x 26 inch) and secure the fitting with the clamp that you retained (Figure 36) Figure 37 1. O-ring (large) 5. 90° hub fitting 2. Reducer hub 3.
Installing the Upper T-fitting and Inlet Hose 3. Install the upper T-fitting onto the hub connector and secure the fitting and connector with the retainer (Figure 39) that you removed in step 2 of Removing the Inlet Hose (page 18). 1. Install the 2 large O-rings into the O-ring grooves at either end of the hub connector (Figure 38) 4.
9 Installing the Hose between the Upper T-fitting and the Ball Valve Parts needed for this procedure: 1 Hose clamp 1 Retainer Figure 42 1. Transfer hose 1.9 x 61 cm (3/4 x 24 inch) 3. Straight-barbed fitting (ball valve) 2. Hose clamp Procedure Note: To insert the barbed fitting into the hose more easily, apply a light coat of a non-petroleum-based lubricant, such as vegetable oil to the barbed end of the fitting. 4. Secure the hose to the barbed fitting with a hose clamp (Figure 42). 1.
11 Installing the Hose Between the Pressure-Filter Assembly and the 4-Way Valve Parts needed for this procedure: Hose 1.9 x 61 cm (3/4 x 24 inch) 2 Hose clamp Procedure Figure 43 1. Straight-barbed fitting 1 Note: To insert the barbed fitting into the hose more easily, apply a light coat of a non-petroleum-based lubricant, such as vegetable oil to the barbed end of the fitting. 3. Hose 1.9 x 76 cm (3/4 x 30 inch) 2. Hose clamp 1. Assemble the hose 1.
12 Installing the Rinse Nozzle Hoses Parts needed for this procedure: 2 Hose 1.9 x 48.3 cm (3/4 x 19 inch) 1 Hose 1.9 x 61 cm (3/4 x 24 inch) 1 Tee fitting 6 Hose clamp Figure 46 Procedure Note: To insert the barbed fitting into the hose more easily, apply a light coat of a non-petroleum-based lubricant, such as vegetable oil to the barbed end of the fitting. 2. Hose clamp 4. Barbed T-fitting 2. Barbed T-fitting 4. Hose 1.9 x 61 cm (3/4 x 24 inch) 7.
13 Connecting the Spray Hose and Gun Parts needed for this procedure: 1 Hose 1.3 x 762 cm (1/2 x 300 inch) 1 Spray gun 2 Hose clamp 1 Spray gun barbed fitting Figure 48 1. Straight barbed-fitting 3. Hose 1.3 x 762 cm (1/2 x 300 inch) 2. Hose clamp Procedure Note: To insert the barbed fitting into the hose more easily, apply a light coat of a non-petroleum-based lubricant, such as vegetable oil to the barbed end of the fitting. 4.
15 Installing Decals Parts needed for this procedure: 3. Hose clamp 2. Straight-barbed fitting (tank rinse pump) 4. Hose 1.9 x 114 cm (3/4 x 45 inch) Decal (120-0673) 1 Decal (120–0687) Procedure Figure 49 1. Hose conduit 1 1. Thoroughly clean the surface of the 4-way valve bracket and ball valve bracket (Figure 51 and Figure 52). 3. Slip the hose conduit over the hose leaving about 30 cm (1 ft) of the free end of the hose exposed (Figure 49 and Figure 50). Figure 51 Figure 50 1.
Operation Tank Clean Rinse Kit Operation Using the Tank Clean Rinse Kit creates a rinsate; a diluted solution of residual chemicals. In many cases it is appropriate to apply the rinsate onto the treated areas. However, before doing so, check with the manufacturer of the chemical to ensure that the application of a diluted solution to the treated areas will not adversely affect the performance of the product.
• This is the boom configuration (Figure 55). Use this configuration to spray rinse water out of the booms. Important: Do not set the ball valve in this position when you operate the main chemical pump. Figure 55 4–way valve + Ball Valve Controls rinse tank contents into the main tank. During this time, the switch will stay in the up position. After 60 seconds, the pump stops running. The switch will remain in the up position until moved to the center or neutral position.
Maintenance Using the Rinse Cycle Using the rinse cycle allows the vehicle to be moving during the rinse processes. Inspecting the Rinse Pump Filter 1. Position the sprayer on a level surface, set the parking brake, stop the pump, stop the engine, and remove the ignition key. Service Interval: After the first 5 hours 2. Remove the rinse tank cap and fill the tank with approximately 66 L (17.5 US gallons) of clean water. Replace the cap Every 50 hours Check the filter for any signs of damage.
Notes: 29
Declaration of Incorporation Model No. 41155 Serial No. Product Description Invoice Description General Description Directive 315000001 and Up EU Compliance Kit, 2015 and After Multi Pro 1750 Turf Sprayer EU COMPLIANCE KIT MP1750 KZ VALVE Turf Sprayer 2006/42/EC, 2004/108/EC Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC.
International Distributor List Distributor: Country: Phone Number: Distributor: Phone Number: 57 1 236 4079 Colombia Japan 81 3 3252 2285 Czech Republic 420 255 704 220 420 255 704 Slovakia 220 Argentina 54 11 4 821 9999 Russia 7 495 411 61 20 Ecuador 593 4 239 6970 Finland 358 987 00733 Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation Hungary Hong Kong Korea 36 27 539 640 852 2155 2163 82 32 551 2076 Maquiver S.A. Maruyama Mfg. Co. Inc. Mountfield a.s.
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
