Installation Instructions

ManualsBrandsToro ManualsSprayersRear Work Light Kit, Multi Pro Turf Sprayer Vehicle

FormNo.3401-380RevB

RearWorkLightKit

MultiPro

TurfSprayerVehicle

ModelNo.41010

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparetoinstalltherearworklightkit.

LEDlight2

Light-mountbracket2

Nut2

AssembletheLEDlightstothebrackets.

Switchbracket

Rockerswitch2

Wireharness1

Assembletheswitchesandthewire

harness.

Nopartsrequired

–

Removetheleftfender(MultiPro1750).

Cabletie

6Routethewireharness.

Fuseblock1

10Afuse

Connectthewireharnesstothefuse

block.

Nopartsrequired

–

Installtheleftfender(MultiPro1750).

Nopartsrequired

–

Finishtherearworklightkitinstallation.

Nopartsrequired

–

ChecktheLEDlights

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3401-380*B

Summary of content (12 pages)

PAGE 1
Form No. 3401-380 Rev B Rear Work Light Kit Multi Pro® Turf Sprayer Vehicle Model No. 41010 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 6 7 8 9 10 © 2016—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Qty.
PAGE 2
WARNING 1 Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. Preparing to Install the Rear Work Light Kit • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable. No Parts Required • Always connect the positive (red) battery cable before connecting the negative (black) cable. Procedure 1.
PAGE 3
4 Assembling the Switches and the Wire Harness Removing the Left Seat Base and Fender (Multi Pro 1750) Parts needed for this procedure: No Parts Required 1 Switch bracket 2 Rocker switch 1 Wire harness Procedure 1. Remove the 3 bolts (5/16 x 1 inch) and 3 washers (5/16 inch) that secure the left seat base and fender to the chassis of the machine (Figure 3). Procedure 1. Align the rocker switch to the opening in the switch bracket (Figure 2).
PAGE 4
Note: Release the parking brake handle if necessary to provide clearance for the seat base; set the parking brake after the seat base and fender are removed from the machine. Figure 5 1. Flange locknut (3/8 inch) 5. Back of the machine 2. LED light and bracket 6. Mount (fresh-water tank) 3. U-bolt (3/8 x 3-1/2 x 2-13/16 inches)—rear work light kit 7. U-bolt (3-1/2 inches)—fresh water-tank mount 4. ROPS tube Figure 4 2.
PAGE 5
Assembling the Lights to the 4-Post ROPS Frame (Multi-Pro WM) 2. Repeat step 1 for the LED light and bracket at the other side of the ROPS tube. 3. Torque the locknuts to 37 to 45 N∙m (27 to 33 ft-lb). 1. Assemble the LED light and bracket to the rear ROPS tube with the U-bolt (3/8 x 3-1/2 x 2-13/16 inches) and flange locknut (3/8 inch) as shown in Figure 7. Note: Use the diagonal-mounting holes in the light bracket. Figure 7 1. Flange locknut (3/8 inch) 3. Light-mount bracket 2.
PAGE 6
Figure 11 1. Engine sprocket and belt 5. Cable tie 2. Front of the machine 6. Upper front-frame tube (left side) 3. Clearance between the wire harness and engine sprocket and belt 7. Top of the machine 4. Wire harness (rear work light kit) Figure 10 1. ROPS tube 3. Wire harness (rear work light kit) 2. Cable tie 4. Back of the machine 2. At the light switches, route the branch of the wire harness with the socket terminal and ring terminal down and forward as shown in Figure 11 and Figure 12.
PAGE 7
Multi Pro 5800 Machine 1. At the switches, route the branch of the wire harness with the 2-socket connector up and across the back of the horizontal ROPS tube as shown in Figure 13. Figure 13 1. Cable tie 2. Wire harness (rear work light kit) Figure 14 3. ROPS tube 4. Back or the machine 1. Wire harness (rear work light kit) 3. Cable tie 2. Back or the machine 4. ROPS tube and plate 2.
PAGE 8
Multi Pro WM Machine 1. At the switches, route the branch of the wire harness with the 2-socket connector up and across the back of the horizontal ROPS tube as shown in Figure 16. Figure 18 1. Wire harness (sprayer) 4. Secure the wire harness for the rear work light kit to the wire harness for the sprayer with cable ties as shown in Figure 16 and Figure 17. Figure 16 1. Wire harness (rear work light kit) 3. ROPS tube 2. Cable tie 4.
PAGE 9
7 Connecting the Wire Harness to the Fuse Block Parts needed for this procedure: 1 Fuse block 1 10A fuse Figure 21 Procedure 3. Install the fuse (10A ) into the fuse-block socket for the LED lights (Figure 22). 1. Connect the wire harness to the fuse block and grounding wire to the grounding block (Figure 20). Note: Multi Pro 1750 and Multi Pro 5800 machines: The fuse block and grounding block are located under the seat of the machine.
PAGE 10
Multi Pro 5800: Rotate the operator’s seat back and down until it is align to the seat box of the chassis; refer to the Operator’s Manual for the Multi Pro 5800 machine. 4. Assemble seat base to the chassis of the machine with the 3 bolts (5/16 x 1 inch) and 2 washers (5/16 inch) that you removed in step 1 of 4 Removing the Left Seat Base and Fender (Multi Pro 1750) (page 3) 5. Torque the bolts to 1017 to 1355 N∙m (90 to 120 in-lb). 10 6. If you released the parking brake, set the parking brake.
PAGE 11
switches; refer to Figure 2 of 2 Assembling the LED Lights to the Brackets (page 2). E. Connect the battery; refer to 9 Finishing the Rear Work Light Kit Installation (page 10). 4. Press the rocker switches up to the ON position to illuminate the LED lights. 5. Press the rocker switches down to the OFF position to shut off the LED lights.
PAGE 12