Form No. 3358-557 Rev B Power Max® 826 OE Snowthrower Model No. 38629—Serial No. 280000001 and Up Operator's Manual Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product.
Safety Caution: Improper use may result in loss of fingers, hands, or feet. Before Operating ? ? Read and understand the contents of this manual before operating the snowthrower Become familiar with all controls and know how to stop the engine quickly . . There is a high-speed impeller close to the opening. Operator 's Position The low-speed auger has a moving pinch point close to the opening. Preparation This snowthrower meets or exceeds the ISO standard 8437 in effect at the time of production.
wear safety glasses or eye shields during operation or while performing an adjustment or repair. • Use only attachments and accessories approved by the manufacturer of snow thrower (such as wheel weights, counterweights, cabs, etc.). Operation • Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run. • Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.
• Do not wear loose-fitting clothing that could get caught in moving parts. container. Remove the key from the ignition switch before storing the snowthrower. • If a shield, safety device, or decal is damaged, illegible, or lost, repair or replace it before beginning operation. Also, tighten any loose fasteners. • Purchase only genuine Toro replacement parts and accessories. • Do not smoke while handling gasoline. Sound Pressure • Do not use the snowthrower on a roof.
112-6625 Reorder part no. 112-6629 1. Cutting/dismemberment hazard, impeller—do not place your hand in the chute; stop the engine before leaving the operator’s position, use the tool to clear the chute. 112-6626 1. Traction drive—squeeze the lever to 5. Thrown object hazard—keep 3. Cutting/dismemberment hazard, engage; release the lever to disengage. bystanders a safe distance from the impeller—do not place your hand in the snowthrower.
Briggs Part No. 277566 1. When starting a cold engine, close the choke and press the primer two times. 2. When starting a warm engine, open the choke and do not press the primer. Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1. 2. 3. 4. 5. 6. 7. Description Qty. Use Handle bolts Curved washers Locknuts 4 4 4 Install the upper handle. No parts required – Install the traction control linkage.
1. Installing the Upper Handle 4 Handle bolts 4 Curved washers 4 Locknuts 2. Installing the Traction Control Linkage Procedure 1. Remove the hairpin cotter and washer from the lower end of the speed control rod and insert the lower end of the rod into the lower link arm so that the bent end of the speed control rod faces rearward (Figure 5). Procedure Note: Do not remove the rubber band on the cables until you have installed the upper handle. 1.
cap down (but do not move the Quick Stick) and rotate the discharge chute until they do. 3. Align the flattened back end of the long chute control rod with the flattened front end of the short rod that extends from the control panel so that they nest together (Figure 9). Figure 7 6. Lift up on the speed control rod and insert the trunnion into the hole in the speed selector lever (Figure 6).
Note: Do not spill oil around the oil fill tube; oil could leak onto traction parts and cause the traction to slip. 5. Checking the Tire Pressure Procedure The tires are overinflated at the factory for shipping. Reduce the pressure equally in both tires to between 17 and 20 psi (116 and 137 kPa). Figure 11 1. Cable clip 2. Deflector cable 7. Hold the blue trigger cap down and rotate the Quick Stick in a circle to ensure that the chute and deflector operate smoothly. 6.
Product Overview The snowthrower should move rearward. If the snowthrower does not move or moves forward, complete the following: A. Release the traction lever and stop the engine. B. Disconnect the trunnion from the speed selector lever (Figure 6). C. Turn the trunnion downward (clockwise) on the speed control rod (Figure 6). D. Connect the trunnion to the speed selector lever (Figure 6). 4. Release the traction lever. 5. Move the speed selector to the Position 1; refer to Operating the Speed Selector. 6.
Figure 16 1. Snow cleanout tool (attached to the handle) Operation Note: Determine the left and right sides of the machine from the normal operating position. Filling the Fuel Tank Figure 17 1. 1-1/2 inch (3.8 cm) Gasoline is extremely flammable and explosive. A fire or explosion from gasoline can burn you and others. Starting the Engine • To prevent a static charge from igniting the gasoline, place the container and/or snowthrower on the ground before filling, not in a vehicle or on an object. 1.
Figure 21 6. Move the throttle to the Fast position (Figure 22). Figure 19 1. Ignition key 4. Firmly push in the primer with your thumb 2 times (15°F or -9°C or above) or 4 times (below 15°F or -9°C), holding the primer in for a second before releasing it each time (Figure 20). Figure 22 7. Start the snowthrower pulling the recoil starter or pressing the electric-starter button (Figure 23). Figure 20 Figure 23 1. Electric-starter button 2. Electric starter plug 5.
start it again). If the engine still does not start, take the snowthrower to an Authorized Service Dealer for service. 8. Disconnect the power cord from the power outlet first and then from the snowthrower (electric start only). 9. Allow the engine to warm up for several minutes, move the choke toward the Run position. Wait for the engine to run smoothly before each choke adjustment. Figure 25 5. Pull the recoil starter 3 or 4 times. This helps prevent the recoil starter from freezing up.
traction lever locks the auger/impeller lever down, freeing your right hand. To release both levers, simply release the left hand (traction) lever. 3. If the auger and impeller continue to rotate when you release the auger/impeller lever, do not operate the snowthrower. Check the auger/impeller cable (refer to Checking and Adjusting the Auger/Impeller Cable) and adjust it if necessary. Otherwise, take the snowthrower to an Authorized Dealer for service. Figure 26 2.
Unclogging the Discharge Chute If the auger/impeller is running but there is no snow coming out of the discharge chute, the discharge chute may be clogged. • To unclog the discharge chute, stay in the operating position and release the left hand (traction) lever. While running the auger/impeller, push down on the handles to raise the front of the snowthrower a few inches (centimeters) off the pavement. Then lift the handles quickly to bump the front of the snowthrower on the pavement.
Operating Tips When the snowthrower is in operation, the impeller and auger can rotate and cut off or injure hands and feet. • Before adjusting, cleaning, inspecting, troubleshooting, or repairing the snowthrower, stop the engine and wait for all moving parts to stop. Disconnect the wire from the spark plug and keep it away from the plug to prevent someone from accidentally starting the engine. • Remove an obstruction from the discharge chute; refer to Unclogging the Discharge Chute.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 2 hours • Inspect the traction cable and adjust it if necessary. • Inspect the auger/impeller cable and adjust it if necessary. After the first 5 hours • Change the engine oil. Before each use or daily • Check the engine oil level and add oil if necessary.
Checking and Adjusting the Skids and Scraper Checking and Adjusting the Traction Cable Service Interval: Yearly—Check the skids and the scraper and adjust them if necessary. Service Interval: After the first 2 hours—Inspect the traction cable and adjust it if necessary. Check the skids and the scraper to ensure that the auger does not contact the paved or gravel surface. Adjust the skids and the scraper as needed to compensate for wear.
Figure 35 1. Jam nut Figure 37 2. Turnbuckle 1. Tab 2. 1/16 inch (1.5 mm) Checking and Adjusting the Auger/Impeller Cable 4. If the auger/impeller cable is not properly adjusted, do the following steps: 5. Loosen the jam nut (Figure 38). Service Interval: After the first 2 hours—Inspect the auger/impeller cable and adjust it if necessary. Yearly—Inspect the auger/impeller cable and adjust or replace it if necessary. 1. Remove the 2 screws from the right side of the belt cover as shown. 2.
Checking the Auger Gearbox Oil Level Service Interval: Yearly—Check the auger gearbox oil and add oil if necessary. Figure 40 1. Move the snowthrower to a level surface. 1. Oil drain cap 2. Clean the area around the pipe plug (Figure 39). 2. Slide an oil drain pan under the drain extension and remove the oil drain cap. 3. Drain the oil. Note: Dispose of the used oil properly at a local recycling center. 4. Install the oil drain cap. 5. Fill the crankcase with oil.
4. Remove the bracket thumb screw and the bracket (Figure 44). Figure 42 1. Back cover 4. Move the speed selector lever to Position R2. 5. Dip your finger in automotive engine oil and lightly lubricate hex shaft. 6. Move the speed selector lever to Position 6. 7. Lubricate the other end of the hex shaft. 8. Move the speed selector lever forward and rearward a few times. 9. Install the back cover and return the snowthrower to the operating position. Figure 44 Replacing the Spark Plug 3. Thumb screw 1.
12. Align the tab on the choke control knob with the slot on the upper snow hood. 13. Connect the choke control knob to the choke shaft on the carburetor. Adjusting the Discharge Chute Latch If the discharge chute does not lock into the desired position or does not unlock so that you can move it to another position, adjust the discharge chute latch. Figure 48 1. Discharge chute latch 1.
Storage 16. Touch up chipped surfaces with paint available from an Authorized Service Dealer. Sand affected areas before painting, and use a rust preventative to prevent the metal parts from rusting. 17. Tighten all loose screws, bolts, and locknuts. Repair or replace any damaged parts. • Gasoline vapors can explode. • Do not store gasoline more than 30 days. 18. Cover the snowthrower and store it in a clean, dry place out of the reach of children.
Troubleshooting Problem Possible Cause Electric starter does not turn (electric-start models only) 1. The power cord is disconnected at the outlet or the snowthrower. 1. Connect the power cord to the outlet and/or the snowthrower. 2. The power cord is worn, corroded, or damaged. 3. The power outlet is not energized. 2. Replace the power cord. 1. The key is not in the ignition or is in the Stop position. 1. Insert the key into the ignition and turn it to the On position. 2.
Problem Possible Cause Corrective Action 7. The auger/impeller drive belt is worn or broken. 7. Replace the auger/impeller drive belt; refer to www.Toro.com for servicing information or take the snowthrower to an Authorized Service Dealer. Discharge chute either does not lock into place or does not move 1. The discharge chute latch is not properly adjusted. 1. Adjust the discharge chute latch. Snowthrower does not properly clear the snow off the surface 1.
Notes: 26
International Distributor List Distributor: Atlantis Su ve Sulama Sisstemleri Lt Balama Prima Engineering Equip B-Ray Corporation Casco Sales Company Ceres S.A CSSC Turf Equipment (pvt) Ltd Cyril Johnston & Co Equiver Femco S.A. G.Y.K. Company ltd. Geomechaniki of Athens Guandong Golden Star Hako Gorund and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Ibea S.p.A. Irriamc Jean Heybroek b.v. Lely (U.K.) Limited Maquiver S.A. Maruyama Mfg. Co. Inc. Metra Kft Mountfield a.s.
The Toro Warranty Conditions and Products Covered Instructions for Obtaining Warranty Service The Toro® Company and its afliate, Toro Warranty Company, pursuant to an agreement between them, jointly promises to the original purchaser* to repair any Toro Product used for normal residential purposes* if defective in materials or workmanship.
