FORM NO. 3320-672 OPERATOR'S MANUAL ( MODEL NO. 38171 & UP MODEL NO. 38176 & UP m CCR POWERLITE®* SNOW THROWER J INSTRUCTIONS To assure maximum safety, best performance, and to gain knowledge of the product, { k read and understand the contents of this manual before the motor Is ever started. Pay particular attention to the safety alert symbol £l which means CAUTION, WARNING OR DANGER “personal safety Instruction.” Read and understand the Instruction because it has to do with safety.
A\ SAFETY INSTRUCTIONS 21. Use extreme caution when crossing or operating snow thrower on walks or roads. It is not recommended that snowblower be used on graver or crushed rock drives. Stay alert for hidden hazards or traffic. Refer to Operating Instructions, page 8, item § for comet operating procedure. 22.
TABLE OF CONTENTS Page Assembly Instructions . 8 Before Operating .. Starting/Stopping Instructions . Operating Instructions Maintenance Draining Gasoline . . Replacing Gator Blades gringos Replacing Scraper Replacing Drive Belt Replacing Spark Pius . .8 Adjusting Carburetor . . .10 Storing Snow thrower .10 Toto Service Support Product Identification . 10 ASSEMBLY INSTRUCTIONS Note: Determine left and right sides of snow thrower by standing in the normal operating position. INSTALL DISCHARGE CHUTE (Fig.
BEFORE OPERATING A\ WARNING DANGER: Gasoline is extremely flammable and explosive under certain conditions. Do not smoke when handling fuel and keep fuel far away from open flames and sparks. Never buy more than a 30 day supply of gasoline. Store it In an approved container. Keep gasoline out of the reach of children. Refuel outdoors and only when engine is cold. Do not fill tank full. Fill tank to Just below bottom of filler neck, not into filler neck. This space Is for expansion of fuel.
STARTING/STOPPING INSTRUCTIONS STARTING/STOPPING ENGINE (Fig. 4) 1. CONTROLS ~ Key switch, primer, electric start butane, and recoil starker are located on the control panel. The choke lever is just below the lower left comer of the control panel. 2. Tum key 10 ON and move choke lever to ON (far right position). 3.
OPERATING INSTRUCTIONS solid. After engine is shut off, wipe ice and snow off entire unit. IMPORTANT: STORE SNOW THROWER IN OPERATING POSITION ON ITS WHEELS OR HANG ON A WALL BY ITS HANDLE. TIPPING OR STORING UNIT FORWARD ONTO FRONT HOUSING MAY CAUSE HARD STARTING. FOLDING SNOW THROWER (Fig. 6) The CCR POWERLITE® folds compactly for easy transporting or storage. To fold up snow thrower, follow hes instructions: Figure 5 . Chute handle . Chute deflector handle . Detector mounting nuts GN 4.
MAINTENANCE GENERAL MAINTENANCE Keep snow thrower in safe operating condition by cleaning the unit. Check and tighten any loose nuts, bolts, knobs, and screws. The scraper, drive belt, rotor blades, and spark plug should be checked once a year. DRAINING GASOLINE 1. Stop engine. Remove key from switch. 2. Remove cap from fuel tank and use a pump type siphon to drain tel into a clean, approved fuel container. 3. Afire fuel is drained, start engine and let it run until all tel is consumed and engine stops.
MAINTENANCE 4. INSTALLING NEW BLADE The rotor blades are made of laminated rubber, Examine the edge of a blade to see the difference in layer thicknesses (Fig. 8). Both blades must be installed with the thick layer on the Inside of the curve, and the wear indicator holes must be on the drive belt cover side (Fig. 8).
MAINTENANCE Figure 12 1. Rotor pulley 3, tidier putative 2. Drive pulley 4. Drive bat 4. INSTALLING BELT (Fig. 13) —Loop belt around drive pulley. While holding bat with right hand, slip belt onto rotor pulley and rotate rotor with left hand unit belt is completely on rotor pulley. Make sure long end of idler spring is hooked in housing notch and round end of spring is hooked on pin on back of tidier pulley. Lift up tidier pulley amm assembly, squeeze belt together, and route belt under idler pulley. 5.
MAINTENANCE 3. INSTALL SPARK PLUG — Set air gap (Fig. 16} between electrodes at .030” {76 mm). Install plug and tighten to 15 ft-In (20.4 N.m). If torque wrench is not used, tighten plug firmly with wrench by hand; 0O NOT OVER TIGHTEN. Push wire onto spark plug and reinstall control panel. ©.080" (.76 mm) Figure 16 ADJUSTING CARBURETOR The carburetor has been factory set, and no adjustment is required.
Consumer Products THE TOR TOTAL COVERAGE GUARANTEE A Full Two-Year Warranty (Limited Warranty for Commercial Use) What Is Covered By This Express Warranty? “The Toto Company promises to repair any TOR Product used for residential purposes if defective in materials or workmanship for a period of two years from the date of purchase. The cost of parts and (arbor are included, but the customer pays the transportation costs.
