Installation Instructions

ManualsBrandsToro ManualsAttachmentsAccessory Control Kit, Groundsmaster 3200 or 3300 Series Traction Unit

FormNo.3439-411RevA

AccessoryControlKit

Groundsmaster

3200or3300SeriesTractionUnit

ModelNo.31994

InstallationInstructions

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea

ofpotentialdanger.Replaceanydecalthatisdamagedormissing.

decal140-1587

140-1587

1.Horn—15A4.Worklights—10A

2.Headlights—10A

5.ReadtheOperator’s

Manualforfuse

information.

3.Beacon—10A

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Switchmount

Clip(1/4inch)

Speednut

Fusemountplate1

U-typespeednut4

Fuseblock1

Screw(#10x3/4inch)

Installtheclips,speednuts,andfuse

block.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3439-411*A

Summary of content (8 pages)

PAGE 1
Form No. 3439-411 Rev A Accessory Control Kit Groundsmaster® 3200 or 3300 Series Traction Unit Model No. 31994 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal140-1587 140-1587 1. Horn—15 A 4. Work lights—10 A 2. Headlights—10 A 5. Read the Operator’s Manual for fuse information. 3.
PAGE 2
Procedure Description Qty. Use 3 Mount bracket Carriage bolt (1/4 x 2 inches) Locknut (1/4 inch) Hex-head screw (1/4 x 3/4 inch) Flange nut (1/4 inch) Flasher Relay Wire harness Cable tie Fuse cover Thumb screw Push nut Decal Screw (#10 x 3/8 inch) Multi-function switch Hole plug Rocker switch Control cover Hex-head screw (1/4 x 3/4 inch) Switch clip Push rivet 2 4 2 2 2 1 1 1 2 1 2 2 1 2 1 3 1 1 6 2 2 Install the switch mount. 4 No parts required – Route the wire harness.
PAGE 3
2. 2 Install the U-type speed nuts to the fuse-mount plate (Figure 2). Installing the Clips, Speed Nuts, and Fuse Block Parts needed for this procedure: 1 Switch mount 6 Clip (1/4 inch) 2 Speed nut 1 Fuse mount plate 4 U-type speed nut 1 Fuse block 2 Screw (#10 x 3/4 inch) g304335 Figure 2 Procedure 1. 1. U-type speed nuts Install the 6 clips and 2 speed nuts to the switch mount (Figure 1). 3. 2.
PAGE 4
Procedure 3 1. Installing the Switch Mount Loosely install the switch mount around the steering column using 4 carriage bolts (1/4 x 2 inches), 2 mounting brackets, fuse-mount plate, and 4 locknuts (1/4 inch) as shown in Figure 4. Parts needed for this procedure: 2 Mount bracket 4 Carriage bolt (1/4 x 2 inches) 2 Locknut (1/4 inch) 2 Hex-head screw (1/4 x 3/4 inch) 2 Flange nut (1/4 inch) 1 Flasher 1 Relay 1 Wire harness 2 Cable tie 1 Fuse cover 2 Thumb screw 2 Push nut 1.
PAGE 5
2. Install the multi-function switch to the switch mount and secure it using the switch clips under the hole for the switch (Figure 5). 4. Install the flasher and relay to the fuse-mount plate using 2 screws (#10 x 3/8 inch) as shown in Figure 7. g319854 Figure 5 1. Switch clips 2. Multi-function switch g319853 3. Figure 7 Install the rocker switch and hole plugs into the switch mount (Figure 6). 1. Relay 2. Screw (#10 x 3/8 inch) g319855 Figure 6 1. Rocker switch 2. Hole plug 5 3.
PAGE 6
5. Secure the flasher using a cable tie (Figure 8). 6. Plug the harness into the rocker switch and multi-function switch (Figure 8). 8. If the machine is used in North America, connect the bullet connectors as shown in Figure 9. Note: Do not connect the bullet connectors is the machine is used outside of North America. g319849 Figure 9 1. Not connected—for non-North America machines 9. 2. Connected—for North America machines Apply the decal to the fuse cover as shown in Figure 10.
PAGE 7
4 Routing the Wire Harness No Parts Required Procedure 1. Loosen the bolts around the steering-column base (Figure 13) 2. Raise the base up and drill a 22 mm (7/8 inch) hole as shown in Figure 13. g304295 Figure 11 1. Push nut 2. Fuse cover 3. Thumb screw 11. Adjust the control assembly so that the switches are accessible. 12. Tighten all the fasteners. 13. Install the control cover to the switch mount using 2 push rivets and 6 hex-head screws (1/4 x 3/4 inch) as shown in Figure 12.
PAGE 8
g304318 Figure 14 1. Wire harness 6. Route the control wire-harness connector (P05) to the right side of the machine. 7. Connect the control wire-harness connector (P05) to the machine wire-harness connector (P103) on the right side, near the roll bar (Figure 15). 2. Horn connection g304373 Figure 15 1. P05 (control wire-harness connector) 8. 8 2. P103 (machine wire-harness connector) Connect the battery; refer to your machine Operator’s Manual.