Installation Instructions

ManualsBrandsToro ManualsAttachmentsAccessory Control Kit, Groundsmaster 3200 or 3300 Series Traction Unit

FormNo.3439-411RevB

AccessoryControlKit

Groundsmaster

3200or3300SeriesTractionUnit

ModelNo.31994

InstallationInstructions

Note:Models31900,31901,31902,and31907requiretheadditionalPowerHarnessKit(PartNo.140-1559).

ModelswithcabsdonotusethePowerHarnessKit.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea

ofpotentialdanger.Replaceanydecalthatisdamagedormissing.

decal140-1587

140-1587

1.Horn—15A4.Worklights—10A

2.Headlights—10A

5.ReadtheOperator’s

Manualforfuse

information.

3.Beacon—10A

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Switchmount

Clip(1/4inch)

Speednut

Fusemountplate1

U-typespeednut4

Fuseblock1

Screw(#10x3/4inch)

Installtheclips,speednuts,andfuse

block.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3439-411*

Summary of content (12 pages)

PAGE 1
Form No. 3439-411 Rev B Accessory Control Kit Groundsmaster® 3200 or 3300 Series Traction Unit Model No. 31994 Installation Instructions Note: Models 31900, 31901, 31902, and 31907 require the additional Power Harness Kit (Part No. 140-1559). Models with cabs do not use the Power Harness Kit. Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing.
PAGE 2
Procedure Description Qty. Use 3 Mount bracket Carriage bolt (1/4 x 2 inches) Locknut (1/4 inch) Hex-head screw (1/4 x 3/4 inch) Flange nut (1/4 inch) Flasher Relay Wire harness Cable tie Fuse cover Thumb screw Push nut Decal Screw (#10 x 3/8 inch) Multi-function switch Hole plug Rocker switch Control cover Hex-head screw (1/4 x 3/4 inch) Switch clip Push rivet 2 4 2 2 2 1 1 1 2 1 2 2 1 2 1 3 1 1 6 2 2 Install the switch mount. 4 No parts required – Route the wire harness.
PAGE 3
2. 2 Install the U-type speed nuts to the fuse-mount plate (Figure 2). Installing the Clips, Speed Nuts, and Fuse Block Parts needed for this procedure: 1 Switch mount 6 Clip (1/4 inch) 2 Speed nut 1 Fuse mount plate 4 U-type speed nut 1 Fuse block 2 Screw (#10 x 3/4 inch) g304335 Figure 2 Procedure 1. 1. U-type speed nuts Install the 6 clips and 2 speed nuts to the switch mount (Figure 1). 3. 2.
PAGE 4
Procedure 3 1. Installing the Switch Mount Loosely install the switch mount around the steering column using 4 carriage bolts (1/4 x 2 inches), 2 mounting brackets, fuse-mount plate, and 4 locknuts (1/4 inch) as shown in Figure 4. Parts needed for this procedure: 2 Mount bracket 4 Carriage bolt (1/4 x 2 inches) 2 Locknut (1/4 inch) 2 Hex-head screw (1/4 x 3/4 inch) 2 Flange nut (1/4 inch) 1 Flasher 1 Relay 1 Wire harness 2 Cable tie 1 Fuse cover 2 Thumb screw 2 Push nut 1.
PAGE 5
2. Install the multi-function switch to the switch mount and secure it using the switch clips under the hole for the switch (Figure 5). 3. Install the rocker switch and hole plugs into the switch mount (Figure 6). g319855 Figure 6 g319854 Figure 5 1. Switch clips 1. Rocker switch 2. Multi-function switch 5 2.
PAGE 6
4. Install the flasher and relay to the fuse-mount plate using 2 screws (#10 x 3/8 inch) as shown in Figure 7. 5. Secure the flasher using a cable tie (Figure 8). 6. Plug the harness into the rocker switch and multi-function switch (Figure 8). g319853 Figure 7 1. Relay 3. Flasher 2. Screw (#10 x 3/8 inch) g319850 Figure 8 1. Rocker switch connector 2. Relay connector 4. Switch connector 5. Cable tie 3. Flasher connector 7. Plug the wire harness into the relay and flasher (Figure 8). 8.
PAGE 7
This connection sets the flasher rate required for North America vs. non-North America road regulations. g319849 Figure 9 1. Not connected—for non-North America machines 9. 2. Connected—for North America machines g304295 Figure 11 1. Push nut 2. Fuse cover Apply the decal to the fuse cover as shown in Figure 10. 3. Thumb screw 11. Adjust the control assembly so that the switches are accessible. 12. Tighten all the fasteners. 13.
PAGE 8
4. 4 5. Route the control wire-harness connector (P05) to the right side of the machine (Figure 14). Connect the harness. A. Routing the Wire Harness For cab units: Connect the control wire-harness connector labeled TO POWER HARNESS (P05) to the cab wire-harness connector labeled POD CONTROL HARNESS (P04); refer to Figure 15. No Parts Required B. Procedure For ROPs units: 1. Loosen the bolts around the steering-column base (Figure 13) Note: Ensure the additional power harness 2.
PAGE 9
g350514 Figure 14 1. Wire harness 2. Horn connection g304373 Figure 15 1. P05 (control wire-harness connector) 7. 2. P04 (pod control harness connector) Connect the battery; refer to your machine Operator’s Manual.
PAGE 10
Notes:
PAGE 11
Notes:
PAGE 12